Study of fluxing in Al refining process by rotary and crucible furnaces

The process used to obtain recycled Al alloys depends on the scrap quality. Rotary furnaces are normally used in Europe as they allow a great productivity and they can process low quality scrap using a salt flux to protect the molten metal from oxidation. In this article, the effect of the quantity of salt on the metal recovery has been experimentally investigated by melting several types of scrap under a mixture of NaCl–KCl–Na₃AlF₆ salts. The quantity of salt has been related to the salt factor (SF), which is the ratio between the non-metallic content in the scrap and the quantity of salt required. The same levels of salt factor have been tested by melting the scrap in rotary and crucible furnaces. The metal recovery increases with the salt content for both furnaces. The results obtained with the different melting processes are comparable because the yield difference is similar considering different salt factors. Crucible furnace gives greater metal recovery but it cannot replace rotary furnace in Al refining industry due to lower melting capacity. However, the results highlight that the optimisation of the Al refining process can be supported by preliminary tests through crucible furnaces reducing the time and material consumptions.     

Challenges in assessing the environmental consequences of dietary changes

Tom et al. (Environ Syst Decis 1–12, 2015) compared the energy requirements, water footprint, and greenhouse gas emissions of diet regimens recently recommended by the US Department of Agriculture. This editorial comments on a number of challenges related to the use of the results of life-cycle assessment studies to quantify the environmental impacts of dietary shifts.     

TG, FT-IR and NMR characterization of n-C16H34 contaminated alumina and silica after mechanochemical treatment

This paper deals with the application of mechanochemistry to model systems composed of alumina or silica artificially contaminated with n-C16H34. The mechanochemical treatment was carried out by means of a ring mill for times ranging from 10 to 40h. Thermogravimetry and infrared and nuclear magnetic resonance spectroscopies were used for the characterization of the mechanochemical products. The results have indicated that, in the case of alumina, almost all the contaminant n-C16H34 undergoes a complex oxidative reaction path whose end products are strongly held on the surface. These end products are most likely made of crosslinked, partially oxidized hydrocarbon chains bond to the solid surface via COO(-) groups. In the case of silica, the hydrocarbon undergoes a different, equally complex reaction path, but to a lower extent. In this case the end products are most probably carbonylic compounds and graphitic carbon. Then, for both solid matrices, the mechanochemical treatment promotes significant modification of the chemical nature of the polluting hydrocarbon with end products much more difficult to remove from the surface. As the systems studied are models of sites contaminated by aliphatic hydrocarbon, the results are worthy of consideration in relation to the mobility of the contaminants in the environment.     

Identification of stationary sources of air pollutants by concentration statistical analysis

The atmospheric concentrations of benzene, toluene, ethylbenzene and isomeric xylenes (BTEX) in a medium-sized town (S. Maria Capua Vetere, about 32000 inhabitants, Southern Italy) have been determined during working days and weekends in 2006. The procedure used was 24h passive adsorption by samplers distributed throughout the town followed by GC/MS analysis. On a yearly base, the arithmetic mean benzene concentrations were above the limit required by the 2000/69/CE European Directive. The Pearson correlation coefficients of the 24h geometric mean BTEX concentrations were indicative of stationary sources of toluene located in a well circumscribed area of the urban territory, active only during the working days and not officially recognized. The results highlight the effectiveness of the statistical approach used in this study for the identification of pollutant sources.     

Environmental and biological monitoring of iridium in the city of Rome

The use of iridium in the latest catalytic converters to further reduce nitrogen oxide emission in the exhaust of lean-burn engines could result in increased atmospheric levels of this element in high-density vehicle traffic areas. The objective of this study is to assess environmental Ir pollution and its urinary levels in workers and an urban control group. Environmental monitoring inside a tram consisted in air samplings of total suspended particles (TSP), PM10 and PM2.5 carried out during November 2005. Urinary Ir levels were evaluated in 64 municipal tram drivers and in 58 administrative employees as controls. Quantification of Ir in air samples and urine was performed by means of Sector Field Inductively Coupled Plasma Mass Spectrometry. Means+/-standard deviation of Ir levels in TSP, in PM10 and PM2.5 fractions were 1.43+/-1.66, 0.44+/-0.27 and 0.36+/-0.19 pg m(-3), respectively. No statistically significant differences were observed among urinary Ir values in the exposed subjects and control group. The Ir levels in Rome air are still sufficiently low, even if the increased use of new Ir-based catalysts could be of some concern in the near future. The results of our study are of interest as they are a first attempt to explore airborne levels and urinary concentrations of Ir in an urban context at medium-high density of vehicle traffic. Particular attention should be given to the fact that Ir was found in the finest dust particles as the effects of fine particles containing Ir have not yet been studied.     

Remote sensing water observation for supporting Lake Victoria weed management

This paper aims to assess the suitability of remote sensing for enhancing the management of water body resources and for providing an inexpensive way to gather, on a wide area, weed infestation extent and optical parameter linked to the water body status. Remotely sensed satellite images and ancillary ground true data were used to produce land cover maps, trough classification techniques, and water compounds maps, applying radiative transfer models. The study proposed within the framework of the cooperation between Italian Foreign Affair Ministry (through the University of Rome) and Kenyan Authorities has been carried out on the Kenyan part of the Lake Victoria. This lake is one of the largest freshwater bodies of the world where, over the last few years environmental challenges and human impact have perturbed the ecological balance affecting the biodiversity. The objective of this research study is to define the thematic products, retrievable from satellite images, like weed abundance maps and water compound concentrations. These products, if provided with an appropriate time frequency, are useful to identify the preconditions for the occurrence of hazard events like abnormal macrophyte proliferation and to develop an up-to-date decision support system devoted to an apprised territory, environment and resource management.     

Environmental release and mass flux partitioning of PCDD/Fs during normal and transient operation of full scale waste to energy plants

The paper reports on global release and mass partitioning in the flux of residues of PCDD/Fs, evaluated with dedicated field campaigns at a municipal solid waste incineration plant during normal and transient operation. Results are compared with those obtained in other installations equipped with furnaces, energy recovery options and flue gas treatment technologies representative of most of the European incineration plants currently in operation. Levels of the pollutants of interest were determined in all the solid, liquid and gaseous residues produced by every single facility, and the results analysed in terms of the effects arising from the fed waste and the configuration of the plant. PCDD/Fs total release between 1.5 and 45 microg I-TEQ per ton of burned waste was evaluated, with lower values resulting from the adoption of catalytic conversion process for flue gas treatment. Most of the mass flux emitted is associated with solid residues deriving from activated carbon PCCD/F dry removal options, with significant contributions also from fly ash produced by particulate removal devices located immediately downstream the boiler and from scrubber blowdowns treatment sludge. During transient operating conditions the dioxin total release may increase by 50% with comparison to steady-state functioning.     

Decontamination of soil containing POPs by the combined action of solid Fenton-like reagents and microwaves

The effect on halogenated aromatics of solid, non-toxic oxidants such as sodium percarbonate and the urea/hydrogen peroxide complex (Fenton-like reagents) was investigated. A microwaves-assisted, solvent-free method for soil decontamination is presented. It marks a considerable advance in the search of more efficient, environment-friendly procedures for the degradative oxidation of persistent organic pollutants. Residual pollutants in treated soil samples were determined by GC/MS analysis after solvent extraction or direct thermal desorption. Results showed that 4-chloronaphthol, 2,4-dichlorophenoxyacetic acid and p-nonylphenol had been degraded completely, 2,4-dibromophenol to a large extent.