Comprehensive temperature monitoring in an in-vessel forced-aeration static-bed composting process

Comprehensive temperature monitoring was done in an in-vessel forced-aeration static-bed composting process using sewage sludge. The three layers that divided the compost pile horizontally showed different temperature distributions. The temperature of the top layer appeared not to be influenced by the ambient temperature. The temperature of the center area of the top layer was taken to be the representative temperature for evaluating composting start-up performance. The temperature of the bottom layer was strongly influenced by the ambient temperature, and the temperature of the center area of the bottom layer was taken to be the representative temperature for pathogen control as it was the minimum temperature in the reactor. Composting start-up performance was influenced by several factors when the ambient temperature was either below or above 20°C. When the ambient temperature was below 20°C, the time taken to reach 65°C (T ₆₅) was influenced by the temperature of inflowing air, but when the temperature was higher than 20°C, it was influenced by the ratio of sewage sludge to seed compost (F/S). T ₆₅ was least when F/S was 1–2. Received: January 9, 2001 / Accepted: October 10, 2001     

Inactivation of fungi associated with barley grain by gaseous ozone

The use of gaseous ozone as a fungicide to preserve stored barley was studied. The effects of the following operating parameters on the fungicidal efficacy of ozone were examined: 1) the applied ozone dose, 2) ozonation time, 3) water activity of barley, and 4) temperature of barley. The effect of ozonation on germination of barley was also investigated. The experimental results showed that ozone was very effective in inactivation of fungi associated with the barley regardless of whether the fungi were in the forms of spores or mycelia. However, the mycelia were less resistant to ozone. With 5 minutes of ozonation, 96% of inactivation were achieved for spores as well as for mixtures of spores and small amount of mycelia by applying 0.16 and 0.10 mg of ozone/(g barley) x min, respectively. In addition, for sealed storage silos, inactivation of fungi continued when the ozone-containing gas was held inside the silos following a continuous ozone supply. The experimental results also revealed that increases in water activity and temperature of barley enhanced the fungicidal efficacy of ozone. Results of this study also indicated that the inactivation processes could be controlled by simply monitoring the exit ozone from the reactor instead of performing the time-consuming microbial examination. This finding would make the application of ozone in the preservation of cereal grains easier, simpler, and more practically applicable. The experimental results demonstrated that although ozonation above certain strength may reduce barley germination, inactivation of fungi was achieved with ozonation strengths far below the critical point.     

A novel sigma coordinate system to simulate abrupt changes of underwater terrain in a hydrodynamic model: application to Lake Mead,USA

The sigma (SIG) coordinate system in ocean circulation simulation models results inevitably in horizontal pressure gradient error. This problem also emerges in models of deep lakes or reservoirs with the same characteristics of underwater terrain mutation. SIG coordinates reflect vertical relative stratification but cannot be used to calculate horizontal pressure gradient force in places with drastic topographic changes; this results in vertical water temperature and circulation errors. In deep lakes or reservoirs, differences in water density caused by the temperature difference between upper and lower water bodies is the primary cause of thermal stratification phenomena. Lake Mead was used as a case study on steep topography based on Environmental Fluid Dynamics Code (EFDC) model in this study. SIG coordinates result in close agreement between the calibrated temperature time series at the top and middle water layers, but disparity in the bottom water layer. The error emerges in the horizontal pressure gradient error due to the SIG coordinate transformation. Neither increasing the vertical resolution nor adjusting the horizontal viscosity coefficient resolve this error. We test the sigma-zed (SGZ) coordinate which combines Z coordinate and SIG coordinate as a replacement for the SIG coordinate to find that they effectively reduce the model’s runtime and simulation efficiency. The vertical temperature distribution in SGZ coordinate mode is more accurate than the distribution in SIG coordinate mode. The Navier-Stokes horizontal gradient and advection diffusion equation results under SIG coordinates are very sensitive to the pressure gradient. The replacement also enhances resolution near the thermocline, facilitates reclosing of the water bottom and the equal sigma surface, lends significant advantages in terms of vertical temperature in the simulation for local deep water with steep terrain, and shortens runtime for 0.14 h. SGZ mixed coordinates are recommended in the simulation of deep lakes or reservoirs wherein the underwater topography is large (with abundant continuous deep trenches or reefs).

     

Toxic cyanobacteria and microcystin dynamics in a tropical reservoir: assessing the influence of environmental variables

Environmental Science and Pollution Research - Toxic cyanobacterial blooms (TCBs) have become a growing concern worldwide. The present study investigated the dynamic of toxic cyanobacteria and...     

Status of water use and potential of rainwater harvesting for replacing centralized supply system in remote mountainous areas: a case study

Environmental Science and Pollution Research - The failure of the centralized water supply system forced XY community to become more dependent on uncertain and unstable water sources. The results...     

Assessment of total concentrations of heavy metals in industrial sludges from the North of Vietnam and their potential impact on the ecosystem

Environmental Science and Pollution Research - Industrial sludges from wastewater treatment plants of industrial parks and a drinking water treatment plant in northern Vietnam were investigated in...     

Plastic waste as a valuable resource: strategy to remove heavy metals from wastewater in bench scale application

Environmental Science and Pollution Research - Single-use plastic waste is gradually considered a potential material for circular economy. Ion exchange resin obtained from polystyrene waste by...     

Esterification of sugarcane bagasse by citric acid for Pb2+ adsorption: effect of different chemical pretreatment methods

In this study, different pretreatment strategies of sugarcane bagasse prior to citric acid modification were investigated in terms of Pb²⁺ adsorption capacity. Pretreatment strategies included the use of NaOH, HCl, and C₂H₅OH in various concentrations. In order to fundamentally understand how these pretreatment methods affect the modification of sugarcane bagasse by citric acid as well as the Pb²⁺ adsorption capacity of sugarcane bagasse, three main components of sugarcane bagasse namely cellulose, hemicellulose, and lignin were isolated and esterified by citric acid under the same conditions. ATR-FTIR, XPS, SEM, and an analysis of the number of carboxylic acid groups were used to investigate the physicochemical and chemical properties of the materials. These three components were proved to participate in adsorption and induce the esterification with citric acid. Hence, pretreatment with ethanol and 0.01 M NaOH which could retain cellulose, hemicellulose, and lignin in sugarcane bagasse achieved a high Pb²⁺ adsorption capacity, i.e., 122.4 and 97 mg/g after the esterification with citric acid. In contrast, pretreatment with 0.5 M NaOH and 0.1 M HCl removed lignin and hemicellulose, leading to the lowest value of approximately 45 mg/g for citric acid esterified-pretreated sugarcane bagasse. XPS analysis and number of carboxylic group measurement confirmed the esterification between bagasse and citric acid. To understand the adsorption mechanism of adsorbent, two kinetic models including pseudo-first-order model and pseudo-second-order model were applied. The experimental data were well described by the pseudo-second-order model. The adsorption isotherm data were fitted Langmuir and Freundlich.

     

Citrulline in amniotic fluid and the prenatal diagnosis of citrullinemia

We report relatively high citrulline concentration in amniotic fluid of a citrullinemic fetus suggesting that prenatal detection of this condition could be done on this basis in conjunction with a direct or an indirect determination of argininosuccinate synthetase activity in amniotic fluid cells.