Acceleration of floc-water separation and floc reduction with magnetic nanoparticles during demulsification of complex waste cutting emulsions

Waste cutting emulsions are difficult to treat efficiently owing to their complex composition and stable emulsified structure. As an important treatment method for emulsions, chemical demulsification is faced with challenges such as low flocs–water separation rates and high sludge production. Hence, in this study, Fe₃O₄ magnetic nanoparticles (MNPs) were used to enhance chemical demulsification performance for treating waste cutting emulsions under a magnetic field. The addition of MNPs significantly decreased the time required to attain sludge–water separation and sludge compression equilibrium, from 210 to 20 min. In addition, the volume percentage of sludge produced at the equilibrium state was reduced from 45% to 10%. This excellent flocculation–separation performance was stable over a pH range of 3–11. The magnetization of the flocculants and oil droplets to form a flocculant–MNP–oil droplet composite, and the magnetic transfer of the composite were two key processes that enhanced the separation of cutting emulsions. Specifically, the interactions among MNPs, flocculants, and oil droplets were important in the magnetization process, which was controlled by the structures and properties of the three components. Under the magnetic field, the magnetized flocculant–MNP–oil droplet composites were considerably accelerated and separated from water, and the sludge was simultaneously compressed. Thus, this study expands the applicability of magnetic separation techniques in the treatment of complex waste cutting emulsions.     

干湿法结合工艺回收废弃SCR脱硝催化剂中的钛、钒和钨

利用干湿法结合工艺实现废弃SCR脱硝催化剂中Ti、V和W元素的高效分离和浸出,提出成套废弃SCR脱硝催化剂中Ti、V和W的回收技术。以废弃SCR脱硝催化剂为研究对象,优选Ti、V和W元素最佳浸出工况,研究硫酸溶解法回收TiO₂和有机萃取法回收V₂O₅和WO₃的回收率与纯度。结果表明:酸浸还原浸钒最优工艺条件为温度140℃,液固比30∶1;钠化焙烧浸钨最优工艺条件为煅烧温度750℃,反应物与Na₂CO₃配比（质量比）为1∶1.5,在以上条件下V、W浸出率分别达到97.6%、93.6%。利用硫酸溶解法回收得到的TiO₂产物主要以锐钛矿晶型存在形式,在最佳焙烧温度750℃下,TiO₂回收率达到97.17%,纯度为95.35%。利用有机萃取法回收得到的V₂O₅和WO₃产物的回收率和纯度分别为72.47%、75.43%和93.25%、78.26%。     

预处理对园林垃圾混合物料联合厌氧发酵的影响

采用超声、微波及碱热预处理技术强化园林垃圾、厨余垃圾与果蔬垃圾联合厌氧发酵产气性能,并以未进行预处理的实验组作为对照。结果表明:4组实验pH值在2 d内迅速降低至7.24~7.45,反应后期可稳定在7.7~8.0,表明厌氧消化系统有较强的稳定性。挥发性脂肪酸（volatile fatty acids,VFA）浓度在第2~4天内达到最大值。乙酸和丙酸是4组实验中VFA的主要成分,两者比例之和在70%以上。VFA浓度在第13天后降低到500 mg/L以下,且以乙酸为主。氨氮（TAN）浓度在前4 d内出现一定波动,随后逐渐升高至2190~2410 mg/L。游离氨氮（FAN）浓度呈先降低后增加趋势,并在第13天后逐渐趋于稳定,为144~209 mg/L。沼气中甲烷比例在第2天后均超过50%,并在第11~12天时达到最大值61.4%~63.8%。修正的Gomperts模型模拟结果表明:预处理技术可缩短反应体系厌氧产沼的适应时间,提高前期产气速率。除此之外,超声预处理与碱热预处理可显著提高基质甲烷产率,由未处理时的396 mL/g分别提高到601,536 mL/g,而微波预处理使得反应体系甲烷产量略有降低。     

核桃壳生物炭对土壤中镉的钝化修复

通过室内模拟试验,研究了核桃壳生物炭（BC400、BC500、BC600）对人工Cd污染土壤（20 mg/kg）pH、Cd赋存形态分布的影响,并探究可能的修复机理。结果显示:经56 d修复后,与空白对照组相比,10%添加量的核桃壳生物炭BC400、BC500、BC600分别使土壤pH升高了1.07、1.31、1.38,弱酸可提取态Cd含量减少了17.02%、20.20%、24.53%,可还原态Cd含量减少了8.9%、19.1%、38.2%,可氧化态Cd含量增加了44.83%、78.45%、100%,残渣态Cd含量增加了66.03%、71.43%、89.21%。同时,土壤pH与土壤中弱酸可提取态Cd含量呈显著负相关（P<0.01）。综上,核桃壳生物炭能够对Cd污染土壤起到钝化修复作用。     

Development of a static test apparatus for evaluating the performance of three PM2.5 separators commonly used in China

PM_(2.5) separator directly affects the accuracy of PM_(2.5) sampling.The specification testing and evaluation for PM_(2.5) separator is particularly important,especially under China's wide variation of terrain and climate.In this study,first a static test apparatus based on polydisperse aerosol was established and calibrated to evaluate the performance of the PM_(2.5) separators.A uniform mixing chamber was developed to make particles mix completely.The aerosol concentration relative standard deviations of three test points at the same horizontal chamber position were less than 0.57%,and the particle size distribution obeyed logarithmic normal distribution with an R~2 of 0.996.The flow rate deviation between the measurement and the set point flow rate agreed to within ± 1.0% in the range of -40 to 50℃.Secondly,the separation,flow and loading characteristics of three cyclone separators(VSCC-A,SCC-A and SCC112) were evaluated using this system.The results showed that the 50% cutoff sizes(D_(50)) of the three cyclones were 2.48,2.47 and 2.44 μm when worked at the manufacturer's recommended flow rates,respectively.The geometric standard deviation(GSD) of the capture efficiency of VSCCA was 1.23,showed a slightly sharper than SCC-A(GSD = 1.27),while the SCC112 did not meet the relevant indicator(GSD = 1.2 ± 0.1) with a GSD = 1.44.The flow rate and loading test had a great effect on D_(50),while the GSD remained almost the same as before.In addition,the maintenance frequency under different air pollution conditions of the cyclones was summarized according to the loading test.     

底泥原位洗脱过程中氮磷含量与形态变化特征

随着城市化进程的不断推进,城市河流底泥中内源氮磷污染问题日益突出.为研究原位洗脱技术对污染底泥中氮、磷物质和成分的作用效果,以北京市凉水河作为研究对象,分别比较了现场试验洗脱与对照组0~30 cm分层底泥以及实验室模拟洗脱处理前后0~10 cm底泥中pH、E_h（氧化还原电位）、容重、含水率、OM（有机质）、TN、TP和氮、磷形态分布的变化特征.结果表明:①现场洗脱对0~5 cm厚度底泥的处理和模拟洗脱处理均对底泥中pH、E_h、含水率的改变以及其中TN、TP的去除效果表现显著,其中,现场试验洗脱组0~5 cm范围底泥中w（TN）、w（TP）分别较对照组降低了66.4%±17.4%、40.8%±24.4%,模拟洗脱处理对底泥中OM、TN、TP的去除率分别达70.1%±4.8%、66.8%±2.0%、43.1%±3.1%.②原位洗脱技术对底泥中TN的去除主要通过对PON（颗粒态有机氮）的去除来实现,现场和模拟试验过程中PON对TN去除的贡献率分别达55.0%和73.6%.③原位洗脱对底泥中TP的去除主要通过对Al-P（铝结合态磷）、OP（有机磷）的去除来实现,现场和模拟试验中Al-P、OP对TP去除的贡献率分别达37.0%、66.2%和31.3%、43.7%.研究显示,原位洗脱技术可有效去除城市河流底泥处理层中的氮磷物质,并以有机氮、磷物质的去除为主.      

精神活性物质在北京市某污水处理厂中的污染特征与生态风险

为了解污水处理厂对精神活性物质的去除特征及总出水对受纳水体的生态风险,采用固相萃取-高效液相色谱-串联质谱法调查了北京市某污水处理厂中13种精神活性物质的浓度水平与负荷量变化,并运用RQ（risk quotient,风险熵）对总出水中精神活性物质进行风险评估.结果表明:①13种精神活性物质在总进水与总出水中均能检出,总质量浓度平均值分别为2 395.10和63.59 ng/L,其中ρ（EPH）（EPH表示麻黄碱）占比分别为93.9%和67.9%,其次为COD（可待因）与METH（甲基苯丙胺）.污水处理厂上游地表水中ρ（EPH）、ρ（METH）与ρ（KET）（KET为氯胺酮）均高于总出水及其下游地表水,说明上游沿河可能有新的污染源输入.②污水处理厂对NK（去甲氯胺酮）、BE（苯甲酰爱康宁）和MTD（美沙酮）均呈负去除,其他精神活性物质的去除主要发生在二级生物处理与三级处理（超滤膜与UV消毒）阶段.③污水处理厂服务区域内精神活性物质的周内负荷量存在一定波动,AMP（苯丙胺）、METH、MDA（3,4-亚甲二氧基苯丙胺）、MDMA（3,4-亚甲二氧基甲基苯丙胺）、KET与HER（海洛因）的负荷量均在周末升高.④污水处理厂总出水中精神活性物质的生态风险均较低（RQ < 0.10）.研究显示,污水处理厂不能完全去除污水中的精神活性物质,总出水中残留精神活性物质对受纳河流生态系统产生的长期混合效应不容忽视.      

不同浓度锌处理下水稻幼苗对镉的累积效应

为探究锌（Zn）对水稻镉（Cd）累积的影响及其根表铁膜所发挥的作用,选取Cd高累积型水稻品种中9优547（简称"Z547"）和Cd低累积型水稻品种金优402（简称"J402"）,采用温室水培试验,研究0、2、5、10、15和20 μmol/L等6个Zn浓度下水稻幼苗对Cd的累积效应,以及不同浓度Zn处理对根表铁膜生成量的影响.结果表明:①随着c（Zn）的增加,Z547和J402水稻幼苗生物量均呈先增后减的趋势,分别在c（Zn）为2和10 μmol/L时达到最大值.②Z547和J402水稻幼苗中w（Cd）均呈先降后增的趋势,分别在c（Zn）为5和2 μmol/L时达到最小值;当水稻幼苗中w（Cd）达到最小值时,Z547根和地上部中w（Cd）分别为31.65和11.47 mg/kg,J402根和地上部中w（Cd）分别为22.58和14.36 mg/kg.③不同浓度Zn处理下水稻幼苗各部位中w（Cd）均与根表铁膜中w（Mn）、w（Fe）、w（Fe+Mn）呈显著正相关,高铁膜处理水稻幼苗中w（Cd）显著高于低铁膜处理,表明根表铁膜生成量的增加会促进Cd在水稻幼苗中的累积.研究显示,当c（Zn）较低时,c（Zn）的增加会抑制水稻幼苗对Cd的累积;当c（Zn）较高时,c（Zn）的增加会促进水稻幼苗对Cd的累积,而Zn可通过控制根表铁膜的生成来影响水稻幼苗对Cd的累积.      

基于边介数的省域生态廊道构建方法优化

我国城市建设和生态保护工作均对土地资源有大量需求,二者之间的矛盾在经济优先发展区表现尤为明显.为了有效地改善生态环境,管控土地利用并引导其变化发展,需要建设具备不可替代特征的省域生态廊道.最小累积阻力模型（minimum cumulative resistance,MCR）是识别生态廊道最常用、有效的模型,但在应用于省域尺度时,MCR模型识别的潜在廊道路由存在冗余的问题.因此,通过引入网络科学中的边介数指数（edge-betweenness）对MCR模型进行优化,计算潜在廊道路由的边介数指数值,选取出其中最为重要和简明的结构来连通生态源地,即提取潜在路由中的骨干路由（backbone route）和关键战略点（key strategic point）作为不可替代的结构来指导省域生态廊道建设.将优化后的MCR模型应用于广东省,构建了全长5 493 km的省域生态廊道,其中包含生态源地20处,关键战略点11个,骨干生态廊道29条.骨干路由与关键战略点构成的不可替代省域生态廊道（irreplaceable provincial corridor）能够实现"廊道数量和占地面积最少、连通性基本不变"的目标.研究显示,边介数能够对潜在路由进行优化筛选,识别出维护省域生态安全的关键结构;不可替代生态廊道能够指导省域生态规划和土地空间的发展利用,并为更高水平的生态安全环境提供了演进的基础;同时也为土地资源紧张的地区提供了建设生态廊道的参考与依据.      

Analytical methods and environmental processes of nanoplastics

The degradation of plastic debris may result in the generation of nanoplastics (NPs). Their high specific surface area for the sorption of organic pollutions and toxic heavy metals and possible transfer between organisms at different nutrient levels make the study of NPs an urgent priority. However, there is very limited understanding on the occurrence, distribution, abundant, and fate of NPs in the environment, partially due to the lack of suitable techniques for the separation and identification of NPs from complex environmental matrices. In this review, we first overviewed the state-of-the-art methods for the extraction, separation, identification and quantification of NPs in the environment. Some of them have been successfully applied for the field determination of NPs, while some are borrowed from the detection of microplastics or engineered nanomaterials. Then the possible fate and transport of NPs in the environment are thoroughly described. Although great efforts have been made during the recent years, large knowledge gaps still exist, such as the relatively high detection limit of existing method failing to detect ultralow masses of NPs in the environment, and spherical polystyrene NP models failing to represent the various compositions of NPs with different irregular shapes, which needs further investigation.