生物质废弃物快速热解制取富氢气体的实验研究

采用管式炉对红松锯屑快速热解制取富氢气体进行了实验研究,分析了反应器温度、物料粒径和催化剂对热解产物组成的影响.结果表明高温能加快生物质快速热解进程,减少炭和焦油生成量,利于富氢气体的生成,800℃时气态产物比例可达56.9 wt.%,气态产物中H2体积分数由4.3%(500℃下)上升至17.2%,H2 CO体积分数达68.3%.小粒径能增大热解气态产物的比例,但对气态产物组成的影响很小,这可能与红松锯屑本身质地疏松有关.以与生物质直接混合方式添加的煅烧白云石能使热解产物中H2含量增加,但造成产气过程变缓,炭生成量增多,富氢气体总产量未能得到提高.     

以膨润土为辅助添加剂固化/稳定化污泥的试验研究

针对传统以水泥固化污泥,带来的水泥用量大与固化体的浸出液pH过高等问题,提出了以膨润土为添加剂辅助水泥固化/稳定化污泥的思路.通过开展无侧限抗压强度试验、毒性浸出试验,测量掺入膨润土后污泥固化体的强度、重金属浸出率、浸出液COD及pH值,研究该固化/稳定化方法的效果.结果表明,膨润土的掺入极大地提高了固化体的抗压强度,将掺入量为0.4(相对污泥的质量比)的水泥一半用膨润土替代时,固化体的强度提高了6左右.体积安定性也能够满足要求.随膨润土掺入量增加,固化体中锌、铅的浸出率与浸出液的pH值呈现不断减小的趋势,锌与铅的浸出率分别由6.9%下降至0.25%,9.6%下降至5%,pH值由12.3下降至12.1.在强碱条件下及烘干或风干条件下,铜会随着有机物的分解而析出,从而增加铜的浸出率,而膨润土的加入能弥补水泥造成的强碱环境及风干或烘干过程对固化污泥中铜的稳定产生的不利影响.     

Ensuring the continued success of a mulch biowall at a trichloroethylene-contaminated superfund site: Lessons learned

Trichloroethylene (TCE) is a toxic organic compound, which can adversely affect human health. The chemical is one of the most frequently found contaminants in groundwater in the United States and around the world. A landfill in Maryland contaminated with high levels of TCE decades ago was added to the U.S. Environmental Protection Agency's National Priority List (NPL) in 1994. A biowall was installed on the site in 2013 to promote the bioremediation of TCE and subsequently of its degradation products. Six-year monitoring data indicated a steady removal of >99% groundwater TCE at the wall since installation. However, a concurrent buildup of intermediate byproducts was observed downgradient of the wall. An examination of the entire system was necessary to find the reason behind the inefficiency of the biowall. In this study, the background of the site, remediation plan, and installation were assessed. Monitoring data, including the concentration of TCE and its degradation byproducts, and geochemical and physical characteristics were evaluated to understand the conditions and challenges facing decision-makers of this project and possible options to improve biowall efficacy.     

Growth factors, kinetics and biodegradation mechanism associated with Pseudomonas nitroreducens TX1 grown on octylphenol polyethoxylates

The growth properties and biodegradation mechanism of a Gram-negative bacterium, Pseudomonas nitroreducens TX1 that was able to grow on branched octylphenol polyethoxylates (OPEO(n), average n=9.5) as the sole carbon source over a wide concentration range (1-100,000 mgl(-1)) were studied. Analysis of growth factors indicated the highest specific growth rate (micro) of 0.53 h(-1) was obtained at an initial concentration of 5,000 mgl(-1) OPEO(n). An optimal C/N ratio of 12 was obtained for (NH(4))(2)SO(4) as the nitrogen source in a cultivated medium at pH 7. The kinetic analysis demonstrated that bacterial growth and OPEO(n) degradation followed the Monod equation and were based on a substrate concentration inhibition model and pseudo-first-order reaction, respectively. The substrate inhibition coefficient was over 18,000 mgl(-1) and this indicates that the strain has an ability to sustain growth at high concentrations of OPEO(n) and use it as the sole carbon source under such a stress condition. Furthermore, LC-MS analysis showed that the biodegradation mechanism of dodecyl octaethoxylate (AEO8) by P. nitroreducens TX1 was the sequential cleavage of the ethoxylate chain.     

Why Won’t They Come? Stakeholder Perspectives on Collaborative National Forest Planning by Participation Level

Collaboration has taken root in national forest planning, providing expanded opportunities for stakeholder participation in decision-making, but are these processes considered meaningful by key stakeholders? Do the processes result in increased participation by key stakeholders? We present results of a study of stakeholder perspectives of a collaborative planning process on the Grand Mesa, Uncompahgre, and Gunnison National Forests in Western Colorado, U.S.A. The stakeholders were stratified by participation levels in order to explore a possible relationship between participation and perceptions of the collaborative process. We used a Q-methodology approach to compare and contrast perspectives across participant levels in the North Fork Valley Landscape Working Group process. The results demonstrate four distinct perspectives on the collaborative process: 1) The collaborative process is valued by the Forest Service and will directly influence planning decisions; 2) The Forest Service, the collaborative process, and other stakeholders are not to be trusted; 3) The collaborative process is most effective when emphasizing place-specific dialogue that primarily involves stakeholders educating the Forest Service about issues; and 4) Forest planning involves issues requiring the application of scientific knowledge and expertise rather than collaboration. These perspectives were not strongly associated with participation levels, with time constraint being the primary mediating factor affecting participation. There are several possible actions policymakers and planners can take to enhance participation and overcome high rates of nonparticipation.     

再生聚丙烯的洁净化和高质化应用

聚丙烯以其优异的机械性能、高的性价比和多重改性方式成为重要的通用树脂之一,这些产品废弃后产生了种类繁多和数量巨大的再生聚丙烯.通过将再生聚丙烯根据性能和来源进行分类,然后分类阐述各再生聚丙烯物料特点,结合再生聚丙烯改性方式,为高质化应用提出方向.     

含锌废物综合利用项目环境影响评价工程探索

工业生产的废物当中包含多种重金属,例如钢铁厂的粉尘当中就含有锌。含锌粉尘不仅会在高炉内循环和富集,影响高炉的运行,还会造成环境污染。基于此,本文主要分析含锌废物综合利用,对该项目进行环境评价,探讨有效的对策,以提高含锌废物综合利用的科学性,提高环境保护等级。     

Stratification effects on hydrodynamics and mixing at a river confluence with discordant bed

Environmental Fluid Mechanics - Stratification effects induced by density differences between the incoming flows are investigated at a medium-size stream confluence with a highly discordant bed....     

Utilization of MSWI fly ash as partial cement or sand substitute with focus on cementing efficiency and health risk assessment

• Washed MSWI fly ash was used as partial cement or sand substitute. • Sand replacing is beneficial for strength, while cement replacement reduces strength. • Cementing efficiency factor and mortar pore structure explain the strength results. • Health risk assessment was conducted for MSWI fly ash blended cement mortar. • CR and HI contributed by different exposures and heavy metals were analyzed. The strength of cement substituted mortar decreases with the increase in fly ash amount, whereas the strength increases when the fly ash is blended as sand substitute. A mortar with highest strength (compressive strength= 30.2 Mpa; flexural strength= 7.0 Mpa) was obtained when the sand replacement ratio was 0.75%. The k value (cementing efficiency) of fly ash varied between 0.36 and 0.15 for the fly ash fraction in binder between 5% and 25%. The k values of fly ash used for sand replacement were all significantly above that used for cement substitution. The macropores assigned to the gaps between particles decreased when the fly ash was used as sand replacement, providing an explanation for the strength enhancement. The waste-extraction procedure (toxicity-sulphuric acid and nitric acid method (HJ/T 299-2007)) was used to evaluate metal leaching, indicating the reuse possibility of fly ash blended mortar. For the mortar with the mass ratio of fly ash to binder of 0.5%, the carcinogenic risks (CR) and non-carcinogenic hazard quotient (HQ) in sensitive scenario for blended mortar utilization were 9.66 × 10^-7 and 0.06, respectively; these results were both lower than the threshold values, showing an acceptable health risk. The CR (9.89 × 10^-5) and HQ (3.89) of the non-sensitive scenario for fly ash treatment exceeded the acceptable threshold values, indicating health risks to onsite workers. The main contributor to the carcinogenic and non-carcinogenic risk is Cr and Cd, respectively. The CR and HQ from inhalation was the main route of heavy metal exposure.     

A review of measurement methods for peracetic acid (PAA)

• Physical and chemical properties and application of peracetic acid solution. • Determination method of high concentration peracetic acid. • Determination method of residual peracetic acid (low concentration). Peroxyacetic acid has been widely used in food, medical, and synthetic chemical fields for the past several decades. Recently, peroxyacetic acid has gradually become an effective alternative disinfectant in wastewater disinfection and has strong redox capacity for removing micro-pollutants from drinking water. However, commercial peroxyacetic acid solutions are primarily multi-component mixtures of peroxyacetic acid, acetic acid, hydrogen peroxide, and water. During the process of water treatment, peroxyacetic acid and hydrogen peroxide (H₂O₂) often coexist, which limits further investigation on the properties of peroxyacetic acid. Therefore, analytical methods need to achieve a certain level of selectivity, particularly when peroxyacetic acid and hydrogen peroxide coexist. This review summarizes the measurement and detection methods of peroxyacetic acid, comparing the principle, adaptability, and relative merits of these methods.