中国近岸海域优势藻种吸收利用磷的过程

通过现场采样和室内培养实验分析了藻类植物的生长状况和细胞结合态磷对磷酸盐浓度的响应.现场调查结果发现,在水华区域藻类植物的细胞磷库分布特点与非水华区域明显不同.室内培养结果发现,中肋骨条藻和东海原甲藻的最大磷酸盐吸收速率为7.71,2.39μmol/（L·d）,最大比生长率分别为0.517,0.262d^-1,磷酸盐吸收同化率为5.9×10^-8,4.7×10^-7μmol/cell,前者具有更快的磷酸盐吸收能力,更高的比生长率和较低的磷酸盐吸收同化率.2种藻细胞内结合态磷通常占细胞总磷库的50%以上,是细胞磷库主要存在形式.中肋骨条藻种群可以通过藻细胞数量增长来吸收环境中的磷源,而东海原甲藻则会优先满足细胞自身的磷储存后进行细胞增殖.在高浓度磷环境中,东海原甲藻种群的细胞不同结合态磷的质量浓度会达到饱和.磷匮乏时,中肋骨条藻和东海原甲藻的细胞内结合态磷的质量浓度与零时刻相比分别降低了45%和66%,前者明显低于后者.培养过程中,中肋骨条藻单个细胞的细胞表面吸附态磷库（95%）比细胞内磷库（50%）的降低幅度更大,东海原甲藻则与之相反.     

光合细菌强化SBR系统处理垃圾渗滤液及生物群落结构分析

从垃圾渗滤液中分离得到一株具有脱氮除磷能力的光合细菌R1,经鉴定为沼泽红假单胞菌（Rhodopseudomonas palustris）,将其投加到SBR系统中,研究对其强化处理垃圾渗滤液的效果,并解析反应器中的菌群构成。结果表明:添加了光合细菌的实验组SBR反应器对COD、NH₄+-N和TP去除率分别达到76.895%、65.964%和94.036%,且污泥产量明显少于对照组。高通量测序结果表明:变形菌门、绿弯菌门、厚壁菌门、酸杆菌门和拟杆菌门为主要优势菌门。在Caldilineaceae、Acinetobacter、Pseudomonas等共同作用下,R1不仅能够稳定存在于活性污泥中,还能够有效改善活性污泥中微生物群落结构,提升其脱氮除磷的性能。     

北方湖库沉积物重金属区域特征及生态风险评价

以白洋淀、衡水湖、于桥水库、松花湖、大伙房水库和小兴凯湖沉积作为研究对象,通过对北方六湖库沉积物中Cu、Zn、Pb、Cr、Ni等重金属元素进行分析,并与国内外其他水域重金属污染情况进行多因素比较,探讨了六湖库主要重金属污染源的差异性,区域分布特征以及与国内外其他水域污染的相似性和区别.结果表明,六湖库沉积物重金属污染处于中等偏下水平.六湖库之间主要重金属污染源存在差别.沉积物重金属含量未出现明显上升的趋势.其中Zn、Pb存在富集现象,但Pb含量与历史数据相比出现下降,Zn的含量与其他地区相比整体偏高.大伙房水库沉积物重金属污染较重,Cu、Zn、Pb、Cr、Ni含量平均值分别为56.28,142.3,17.44,97.9,44.44mg/kg.小兴凯湖沉积物重金属含量最低,Cu、Zn、Pb、Cr、Ni含量平均值分别为2.41,63.90,13.37,56.36,26.09mg/kg.六湖库综合风险评价结果为大伙房水库>于桥水库>白洋淀>衡水湖>松花湖>小兴凯湖,重金属整体潜在生态风险指数为低.     

除Cd (Ⅱ)重金属吸附剂——巯基乙酰化玉米秸秆的制备

以玉米秸秆（CS）、巯基乙酸（TGA）为原料,通过化学反应制备出重金属吸附剂——巯基乙酰化玉米秸秆（MACS）,考察MACS对水样中Cd （Ⅱ）的去除性能,采用单因素实验法对MACS的制备条件进行优化研究。结果表明,MACS的优化制备条件为:CS粒径为0.20 mm （80目）,m（催化剂NHS）:m（EDC·HCl）为0.5:1,m（CS）:V（TGA）为1:5,反应介质pH值为5.0,反应温度25℃,反应时间2 h。在此条件下制备的MACS对水样中Cd （Ⅱ）的吸附效率可达到61.57%。红外分析表明,CS分子链中成功引入了巯基。     

基于在线监测+模型的海绵城市建设径流水量控制效果研究

以青岛市海绵城市典型项目区为研究区,通过收集、整理和概化汇水区资料,构建了研究区降雨径流模型——SWMM模型。利用2018年雨季的降雨-径流实时监测数据,进行了模型关键参数的率定和模型验证,研究了海绵城市建设在削减径流量、增加入渗与滞蓄雨量方面的定量效果。结果显示:海绵改造后,不同降雨强度下形成径流的雨量占总雨量的平均比例由56%下降至29%;下渗雨水的平均比例由40%增加至60%,滞蓄深度由0.63 mm增加至5 mm。海绵改造前后研究区场降雨径流总量控制率变化显著,当以1~10年一遇的短历时（120 min）设计降雨作为模型边界条件进行模拟时,海绵化改造后场次降雨径流总量控制率提高了26%~34%,认为研究区基本达到了海绵城市关于水量控制的建设要求。     

雨水管道沉积物中典型无机氮的干期粒径分布

以南京江北新区分流制雨水管道沉积物为研究对象,考察不同粒径沉积物中铵态氮（NH₃-N）和硝态氮（NO₃^--N）干期分布特征,分析其随干期长度的变化关系,并探讨沉积物理化性质及微生物菌群结构对NH₃-N和NO₃^--N干期分布的影响.结果表明：粒径≤0.075mm的沉积物中NH₃-N占比最高（交通区30.8%,商业区36.7%）;交通区粒径≤0.075mm的沉积物中NO₃^--N占比最高（33.0%）,而商业区粒径0.075~0.15mm沉积物中NO₃^--N占比最高（34.4%）;干期长度与交通区0.075~0.15mm粒径段的沉积物中NO₃^--N含量及商业区粒径≥0.3mm的沉积物中NH₃-N含量之间的相关性均最显著;雨水管道沉积物中NH₃-N和NO₃^--N的干期分布与O-H和N-H等官能团、表面极性和亲水性、微观形貌等有一定关联;交通区雨水管道沉积物中Gemmobacter等反硝化优势菌种（相对丰度总和为20.15%）对NO₃^--N干期分布影响更显著.     

Acceleration of floc-water separation and floc reduction with magnetic nanoparticles during demulsification of complex waste cutting emulsions

Waste cutting emulsions are difficult to treat efficiently owing to their complex composition and stable emulsified structure. As an important treatment method for emulsions, chemical demulsification is faced with challenges such as low flocs–water separation rates and high sludge production. Hence, in this study, Fe₃O₄ magnetic nanoparticles (MNPs) were used to enhance chemical demulsification performance for treating waste cutting emulsions under a magnetic field. The addition of MNPs significantly decreased the time required to attain sludge–water separation and sludge compression equilibrium, from 210 to 20 min. In addition, the volume percentage of sludge produced at the equilibrium state was reduced from 45% to 10%. This excellent flocculation–separation performance was stable over a pH range of 3–11. The magnetization of the flocculants and oil droplets to form a flocculant–MNP–oil droplet composite, and the magnetic transfer of the composite were two key processes that enhanced the separation of cutting emulsions. Specifically, the interactions among MNPs, flocculants, and oil droplets were important in the magnetization process, which was controlled by the structures and properties of the three components. Under the magnetic field, the magnetized flocculant–MNP–oil droplet composites were considerably accelerated and separated from water, and the sludge was simultaneously compressed. Thus, this study expands the applicability of magnetic separation techniques in the treatment of complex waste cutting emulsions.     

干湿法结合工艺回收废弃SCR脱硝催化剂中的钛、钒和钨

利用干湿法结合工艺实现废弃SCR脱硝催化剂中Ti、V和W元素的高效分离和浸出,提出成套废弃SCR脱硝催化剂中Ti、V和W的回收技术。以废弃SCR脱硝催化剂为研究对象,优选Ti、V和W元素最佳浸出工况,研究硫酸溶解法回收TiO₂和有机萃取法回收V₂O₅和WO₃的回收率与纯度。结果表明:酸浸还原浸钒最优工艺条件为温度140℃,液固比30∶1;钠化焙烧浸钨最优工艺条件为煅烧温度750℃,反应物与Na₂CO₃配比（质量比）为1∶1.5,在以上条件下V、W浸出率分别达到97.6%、93.6%。利用硫酸溶解法回收得到的TiO₂产物主要以锐钛矿晶型存在形式,在最佳焙烧温度750℃下,TiO₂回收率达到97.17%,纯度为95.35%。利用有机萃取法回收得到的V₂O₅和WO₃产物的回收率和纯度分别为72.47%、75.43%和93.25%、78.26%。     

预处理对园林垃圾混合物料联合厌氧发酵的影响

采用超声、微波及碱热预处理技术强化园林垃圾、厨余垃圾与果蔬垃圾联合厌氧发酵产气性能,并以未进行预处理的实验组作为对照。结果表明:4组实验pH值在2 d内迅速降低至7.24~7.45,反应后期可稳定在7.7~8.0,表明厌氧消化系统有较强的稳定性。挥发性脂肪酸（volatile fatty acids,VFA）浓度在第2~4天内达到最大值。乙酸和丙酸是4组实验中VFA的主要成分,两者比例之和在70%以上。VFA浓度在第13天后降低到500 mg/L以下,且以乙酸为主。氨氮（TAN）浓度在前4 d内出现一定波动,随后逐渐升高至2190~2410 mg/L。游离氨氮（FAN）浓度呈先降低后增加趋势,并在第13天后逐渐趋于稳定,为144~209 mg/L。沼气中甲烷比例在第2天后均超过50%,并在第11~12天时达到最大值61.4%~63.8%。修正的Gomperts模型模拟结果表明:预处理技术可缩短反应体系厌氧产沼的适应时间,提高前期产气速率。除此之外,超声预处理与碱热预处理可显著提高基质甲烷产率,由未处理时的396 mL/g分别提高到601,536 mL/g,而微波预处理使得反应体系甲烷产量略有降低。     

Development of a static test apparatus for evaluating the performance of three PM2.5 separators commonly used in China

PM_(2.5) separator directly affects the accuracy of PM_(2.5) sampling.The specification testing and evaluation for PM_(2.5) separator is particularly important,especially under China's wide variation of terrain and climate.In this study,first a static test apparatus based on polydisperse aerosol was established and calibrated to evaluate the performance of the PM_(2.5) separators.A uniform mixing chamber was developed to make particles mix completely.The aerosol concentration relative standard deviations of three test points at the same horizontal chamber position were less than 0.57%,and the particle size distribution obeyed logarithmic normal distribution with an R~2 of 0.996.The flow rate deviation between the measurement and the set point flow rate agreed to within ± 1.0% in the range of -40 to 50℃.Secondly,the separation,flow and loading characteristics of three cyclone separators(VSCC-A,SCC-A and SCC112) were evaluated using this system.The results showed that the 50% cutoff sizes(D_(50)) of the three cyclones were 2.48,2.47 and 2.44 μm when worked at the manufacturer's recommended flow rates,respectively.The geometric standard deviation(GSD) of the capture efficiency of VSCCA was 1.23,showed a slightly sharper than SCC-A(GSD = 1.27),while the SCC112 did not meet the relevant indicator(GSD = 1.2 ± 0.1) with a GSD = 1.44.The flow rate and loading test had a great effect on D_(50),while the GSD remained almost the same as before.In addition,the maintenance frequency under different air pollution conditions of the cyclones was summarized according to the loading test.