建筑安全风险因素分级排序的风险矩阵法

为减少风险分级排序时产生的风险结,在引入施工安全事故频率的基础上,采用单元格细化和Borda序值法改进原有的风险矩阵法。改进后的方法使得风险等级数量增加,风险结数量减少。将该方法应用于脚手架工程的风险因素的分级与排序,风险等级分为6级,且实现了12个因素的明确排序。     

基于VR技术的机场应急救援虚拟演练平台

为解决机场实地应急演练中存在的成本消耗高、不安全、扩展性差等问题,研发基于VR技术的机场应急救援虚拟演练平台。平台采用模块化设计方案,并通过定义平台操作流程支持虚拟演练操作。采取分细节度的场景构建方法,运用细节层次模型以3层不同细节度模型方案将虚拟灾害场景划分为3类,同时利用Unity3D粒子系统控制机制实现火灾及灭火粒子特效的模拟,运用双顶层本体模型构建机场应急预案本体模型（AERPO）,并利用XML Spy建立存储模型,且支持基于典型场景模型编辑形成整个灾害场景。结果表明:平台模块设置科学、场景效果合理,有助于提升演练人员应急处置能力。     

单芯铜线过电流故障电弧熔痕的微观特征研究*

为准确认定电气火灾中过电流故障,模拟4~7倍额定电流（Ie）条件下单芯铜导线过电流故障,利用光学显微镜和扫描电子显微镜（SEM）分析过电流故障电弧熔痕的组织特征,并结合Image-Pro Plus软件测定晶粒直径、周长和面积,探究金相组织的量化判据和变化规律。结果表明:当I＝4Ie时,过电流故障电弧熔痕的金相组织主要为方向性较强的树枝晶;当I＝5Ie,6Ie时,金相组织内树枝晶占比减小,胞状晶占比升高;当I＝7Ie时,方向性较弱的胞状晶占主导。随着电流增加,晶粒的平均直径、周长和面积均呈增长趋势。通过火灾案例分析可知,实验结果与现场的电弧熔痕组织特征基本相符,验证火灾事故原因为过电流故障。     

基于非线性技术锅炉故障分析*

为预测和判断锅炉故障的发生,完善锅炉故障检测技术,基于锅炉运转具有非线性特点,提出将非线性评价指标应用于锅炉故障诊断。研究特征信号的非线性特性,通过确定延迟时间和嵌入维数来重构相空间;采用混沌分形理论研究非线性评价指标;提取最大Lyapunov指数和关联维数,并为收集的每种特征信号选择最合适的非线性指标。结果表明:蒸汽压力的非线性特征指标应选择关联维数,烟气温度1、烟气温度2、水管温度1和水管温度2的非线性特征指标应当选择最大Lyapunov指数。     

煤矿水害风险量化评价方法

为提高煤矿防治水管理水平,预防和消除矿井水害,在层次分析法的基础上建立中性值作为参照对象对矿井水害风险进行实时评判的方法。根据《煤矿防治水细则》建立以矿井水文地质类型、矿井涌水量标准分数、突水预兆、采掘面位置、探水结果为准则层的层次结构模型,并对各评价指标赋权。依据制定的水害风险评价指标的评分细则和监测监控数据并结合其权重得到水害评价总得分。通过总得分与中性参照分数比较得出预测结果:水害评价总得分大于中性参照分数,证明水害的威胁小,分数越高越安全;反之则水害的威胁较大,分数越低越危险,这时需要加强防治水的力度,令评价分数管控大于中性参照分数。这种方法依赖于井下监测监控数据进行量化评价,能实时、客观、全面且准确地反映煤矿水害的风险情况。     

大气降水对金属材料环境适应性能影响研究

考察了大气降水环境下(酸雨)对镀锌钢丝的环境适应性能的影响。结果表明,随着盐雾腐蚀时间的延长,钢丝表面腐蚀深度逐渐增加,盐雾腐蚀时间的延长会使得腐蚀更加严重;盐雾腐蚀时间为40天前表示表面镀锌层发生腐蚀的阶段,而盐雾腐蚀时间超过40天时则为钢丝基体的腐蚀;镀锌层的腐蚀速率要高于钢丝基体。随着腐蚀时间从10天延长至120天,钢丝表面腐蚀坑深度呈现逐渐增加的趋势;镀锌钢丝的点蚀与腐蚀时间的预测模型为:■,■。     

Diffusive gradients in thin films using molecularly imprinted polymer binding gels for in situ measurements of antibiotics in urban wastewaters

• Selective molecularly imprinted polymer (MIP) binding gel was prepared. • MIP-DGT showed excellent uptake performance for antibiotics. • In situ measurement of antibiotics in wastewaters via MIP-DGT was developed. • The MIP-DGT method was robust, reliable, and highly sensitive. Urban wastewater is one of main sources for the introduction of antibiotics into the environment. Monitoring the concentrations of antibiotics in wastewater is necessary for estimating the amount of antibiotics discharged into the environment through urban wastewater treatment systems. In this study, we report a novel diffusive gradient in thin films (DGT) method based on molecularly imprinted polymers (MIPs) for in situ measurement of two typical antibiotics, fluoroquinolones (FQs) and sulfonamides (SAs) in urban wastewater. MIPs show specific adsorption toward their templates and their structural analogs, resulting in the selective uptake of the two target antibiotics during MIP-DGT deployment. The uptake performance of the MIP-DGTs was evaluated in the laboratory and was relatively independent of solution pH (4.0–9.0), ionic strength (1–750 mmol/L), and dissolved organic matter (DOM, 0–20 mg/L). MIP-DGT samplers were tested in the effluent of an urban wastewater treatment plant for field trials, where three SA (sulfamethoxazole, sulfapyridine, and trimethoprim) and one FQ (ofloxacin) antibiotics were detected, with concentrations ranging from 25.50 to 117.58 ng/L, which are consistent with the results measured by grab sampling. The total removal efficiency of the antibiotics was 80.1% by the treatment plant. This study demonstrates that MIP-DGT is an effective tool for in situ monitoring of trace antibiotics in complex urban wastewaters.     

Manganese-modified biochar for highly efficient sorption of cadmium

Environmental Science and Pollution Research - In this study, corn stalk was modified by manganese (Mn) before (MBC1) and after (MBC2) pyrolysis at different temperatures (400~600 °C)...     

Magnetic nanoparticles incorporation into different substrates for dyes and heavy metals removal—A Review

Environmental Science and Pollution Research - Substantial discharge of hazardous substances, especially dyes and heavy metal ions to the environment, has become a global concern due to...