Effects of Compounded Curing Agents on Properties and Performance of Urea Formaldehyde Resin

The effects of three compounded curing agents on the properties and performance of the urea-formaldehyde (UF) resin were investigated in this study. The compounded curing agents were prepared by mixing ammonium chloride with hexamethylenetetramine, citric acid, and oxalic acid respectively at a ratio of 1:1, named N-H, N–CA, and N–OA, respectively. The curing process, crystallinity, and physical properties were measured, and the three-ply plywood was fabricated to measure its prepress strength, wet shear strength, and formaldehyde emission. Results showed that the compounded curing agents N–CA and N–OA enhanced the initial viscosity, crosslinking density and thermal stability of UF resin. Additionally, the prepress strength of the plywood bonded by UF resin with N–CA and N–OA increased by 82 and 111% respectively compared to the UF resin with NH₄Cl, and the wet shear strength increased by 14 and 16%, the formaldehyde emission decreased by 19 and 42% respectively. However, owing to the short pot-life of these curing agent limited their storage time, the curing agents N–CA and N–OA should be applied to fabricate plywood in winter for obtaining a better bond strength and a lower formaldehyde emission. While the UF resin with N–HT showed a suitable pot-life, so it could be applied to fabricate plywood in summer for long time storage and avoiding procuring problem.     

Production of Curdlan Grown on Cassava Starch Waste Hydrolysates

Cassava starch waste hydrolysates (CSWHs) with different degrees of polymerisation, i.e., CSWHs-1, CSWHs-2 and CSWHs-3, were prepared through the hydrolysis of cassava starch waste with thermostable a-amylase from Thermococcus sp. HJ21. The prepared CSWHs were then used as a carbon source for curdlan production with Alcaligenes faecalis ATCC 31749. The amount of curdlan produced and the glucosyltransferase activity during curdlan synthesis increased more obviously when CSWHs-2 was used as the carbon source than when glucose was used. Using both carbon sources, the maximum curdlan production was observed at day 5, and the maximum glucosyltransferase activity was observed at day 4. Glucosyltransferase activity decreased thereafter, and biomass continued to increase until the end of the experiment (day 6). Results indicated that the enhanced curdlan production with CSWHs as the carbon source was highly correlated with glucosyltransferase activity.     

A panel study on the relationship between biofuels production and sustainable development

Biomass is one of the renewable energy sources on which policy makers are greatly dependent on since it is a flexible feedstock capable of conversion into electricity, transport liquid fuels and heat by chemical and biological processes on demand. Though numerous publications have examined the relationship of economic growth with renewable energy and other parameters, biomass energy has never been included in these studies. Then, this study examines the causal relationship within a multivariate panel cointegration/error correction framework which combines the cross-section and time series data while allowing for heterogeneity across different provinces. After employing panel data regression model ranging from 2003 through 2012 to examine the relationships of biofuels production with sustainable development in China, the paper concludes that the development of biofuel energy production integrated with the consideration of the improvement of income per capita, and the attraction of more capital investment, does make a significant contribution to economic growth. However, some negative side effects including the increase of greenhouse emissions and the decrease of marginal land still coexist with the economic development. Of course, the importance of these findings lies on their implications and their adoption on strategic policies.     

Highly efficient conversion of sugarcane bagasse pretreated with liquid hot water into ethanol at high solid loading

Liquid hot water (LHW), an environmental-friendly physico-chemical treatment, was applied to pretreat the sugarcane bagasse (SCB). Tween80, a non-ionic surfactant, was used to enhance the enzymatic hydrolysis of the pretreated SCB. It found that 0.125 mL Tween80 /g dry matter could make the maximum increase (33.2%) of the glycan conversion of the LHW-pretreated SCB. A self-designed laboratory facility with a plate-and-frame impeller was applied to conduct batch hydrolysis, fed-batch hydrolysis, and the process of high-temperature (50°C) fed-batch hydrolysis following low-temperature (30°C) simultaneous saccharification and fermentation (SSF) which was adopted to overcome the incompatible optimum temperature of saccharification and fermentation in the SSF process. After hydrolyzing LHW-pretreated SCB for 120 h with commercial cellulase, the total sugar concentration and glycan conversion obtained from fed-batch hydrolysis were 91.6 g/L and 68.3%, respectively, which were 9.7 g/L and 7.3% higher than those obtained from batch hydrolysis. With Saccharomyces cerevisiae Y2034 fermenting under the non-sterile condition, the ethanol production and theoretical yield obtained from the process of SSF after fed-batch hydrolysis were 55.4 g/L and 88.3% for 72h, respectively, which were 15.5 g/L and 24.7% higher than those from separate fed-batch hydrolysis and fermentation. The result of this work was superior to the reported results obtained from the LHW-pretreated SCB.     

Current status and historical variations of phthalate ester (PAE) contamination in the sediments from a large Chinese lake (Lake Chaohu)

The residual levels of phthalate esters (PAEs) in the surface and two core sediments from Lake Chaohu were measured with a gas chromatograph–mass spectrometer (GC–MS). The temporal–spatial distributions, compositions of PAEs, and their effecting factors were investigated. The results indicated that di-n-butyl phthalate (DnBP), diisobutyl phthalate (DIBP), and di(2-ethylhexyl) phthalate (DEHP) were three dominant PAE components in both the surface and core sediments. The residual level of total detected PAEs (∑PAEs) in the surface sediments (2.146?±?2.255 μg/g dw) was lower than that in the western core sediments (10.615?±?9.733 μg/g) and in the eastern core sediments (5.109?±?4.741 μg/g). The average content of ∑PAEs in the surface sediments from the inflow rivers (4.128?±?1.738 μg/g dw) was an order of magnitude higher than those from the lake (0.323?±?0.093 μg/g dw), and there were similar PAE compositions between the lake and inflow rivers. This finding means that there were important effects of PAE input from the inflow rivers on the compositions and distributions of PAEs in the surface sediments. An increasing trend was found for the residual levels of ΣPAEs, DnBP, and DIBP from the bottom to the surface in both the western and eastern core sediments. Increasing PAE usage with the population growth, urbanization, and industrial and agricultural development in Lake Chaohu watershed would result in the increasing production of PAEs and their resulting presence in the sediments. The significant positive relationships were also found between the PAE contents and the percentage of sand particles, as well as TOC contents in the sediment cores.     

Increasing the recovery of heavy metal ions using two microbial fuel cells operating in parallel with no power output

The present study aimed to improve the performance of microbial fuel cells (MFCs) by using an intermittent connection period without power output. Connecting two MFCs in parallel improved the voltage output of both MFCs until the voltage stabilized. Electric energy was accumulated in two MFCs containing heavy metal ions copper, zinc, and cadmium as electron acceptors by connection in parallel for several hours. The system was then switched to discharge mode with single MFCs with a 1000-Ω resistor connected between anode and cathode. This method successfully achieved highly efficient removal of heavy metal ions. Even when the anolyte was run in sequencing batch mode, the insufficient voltage and power needed to recover heavy metals from the cathode of MFCs can be complemented by the developed method. The average removal ratio of heavy metal ions in sequencing batch mode was 67 % after 10 h. When the discharge time was 20 h, the removal ratios of zinc, copper, and cadmium were 91.5, 86.7, and 83.57 %, respectively; the average removal ratio of these ions after 20 h was only 52.1 % for the control group. Therefore, the average removal efficiency of heavy metal ions increased by 1.75 times using the electrons stored from the bacteria under the open-circuit conditions in parallel mode. Electrochemical impedance data showed that the anode had lower solution resistance and polarization resistance in the parallel stage than as a single MFC, and capacitance increased with the length of time in parallel.

     

Efficacy of Si fertilization to modulate the heavy metals absorption by barley (Hordeum vulgare L.) and pea (Pisum sativum L.)

Silicon-based fertilizers and soil amendments can have direct and indirect positive influences on cultivated plants. The solid forms of Si-based substances, the most widespread in use, are efficient only at high application rates due to their low level of solubility. Several types of Si-based substances such as fumed silica, slags from the iron and steel industry, modified slags, and a Si-rich product were tested using barley and pea as silicon accumulative and non-accumulative plants, respectively, at two application rates. The plants were grown under toxic concentrations of heavy metals in a greenhouse. Si-rich materials high in water-soluble Si had a positive effect at both the low and high application rates, and for both plant species. This type of substance can be regarded as Si fertilizer, demonstrating greater efficiency at a low application rate and lessened efficiency at a high application rate for protection of the cultivated plants against accumulation of the heavy metals.