生物接触氧化—复合人工湿地组合工艺对工业园区污水的处理效果研究

根据广州从化市玮思工业园排放的综合污水的特点,设计了生物接触氧化—复合人工湿地组合工艺对其进行处理,考察了该工艺运行一年来对COD、BOD5、TP、NH4+ -N、TN的去除效果.结果表明,该组合工艺对工业园区综合污水中的COD、BOD5、TP、NH4+ -N和TN都有较好的去除效果,出水COD、BOD5、TP、NH4+ -N、TN的平均去除率分别为86.07％、74.91％、60.73％、89.62％、46.01％;该组合工艺对各污染物的去除效果明显优于单一的生物接触氧化池和单一的复合人工湿地的去除效果,生物接触氧化池对COD、BOD5和NH4+ -N的去除贡献较大,但对TP和TN的去除能力有限;采用该组合工艺处理工业园区综合污水,具有运行费用低、处理效果好、操作方便、管理简单、景观效果良好等优点.     

Mo-N-TiO_2光催化剂的制备、表征及其活性提高机制

以钼酸铵和氨水分别为钼源和氮源,采用溶胶-凝胶法制备了Mo-N-TiO2光催化剂,并对其进行了XRD、XPS和UV-visDRS表征。XRD结果表明,Mo、N共掺杂有效抑制了TiO2晶粒的生长,提高了TiO2由锐钛矿向金红石相的转变温度。UV-vis表明,Mo-N-TiO2光催化剂可见光吸收能力增强,吸收带边明显＂红移＂,且钼酸铵添加量（相对TiO2）为0.5%的样品＂红移＂程度最大,最大吸收带边为550 nm。XPS分析结果表明,Mo取代了TiO2晶格中的部分Ti4＋,以Mo6＋形式存在的,而N以Ti—N及N—Ti—O形式存在。以罗丹明B为模型污染物,重点考察了钼酸铵添加量与焙烧温度对Mo-N-TiO2光催剂性能的影响。结果表明,400℃焙烧下、钼酸铵添加量为0.5%的样品催化活性最好。模拟太阳光下光照120min对罗丹明B的降解率达到96.8%,是纯TiO2的2.42倍。     

Carbonyl emissions from vehicular exhausts sources in Hong Kong

Vehicular emission (VE) is one of the important anthropogenic sources for airborne carbonyls in urban area. Six types of VE-dominated samples were collected at representative locations in Hong Kong where polluted by a particular fueled type of vehicles, including (i) a gas refilling taxis station (liquefied petroleum gas [LPG] emission); (ii) a light-duty passenger car park (gasoline emission); (iii) a minibus station (diesel emission); (iv) a single-deck-bus depot (diesel emission); (v) a double-deck-bus depot (diesel emission); and (vi) a whole-food market entrance for light- and heavy-duty vehicles (diesel emission). A total of 15 carbonyls in the samples were quantified. Formaldehyde was the most abundant carbonyl among the VE-dominated samples, and its contribution to the total quantified amount on a molar basis ranged from 54.8% to 60.8%. Acetaldehyde and acetone were the next two abundant carbonyls. The carbonyls were quantified at three roadside locations in Hong Kong. The highest concentrations of formaldehyde and acetaldehyde, 22.7 +/- 8.4 and 6.0 +/- 2.8 microg/m3, respectively, were determined in the samples collected at a main transportation gate for goods between Hong Kong and Mainland China. The total quantified carbonyl concentration, 37.9 +/- 9.3 microg/m3, was the highest at an entrance of a cross-harbor tunnel in downtown area. The theoretical carbonyls compositions of the three roadside locations were estimated according to the VE-dominated sample profiles and the statistics on vehicle numbers and types during the sampling period. The measured compositions of formaldehyde were much higher than the theoretical compositions in summer, demonstrating that photochemical reactions significantly contributed to the formaldehyde production in the roadsides.     

Second-order chlorine decay and trihalomethanes formation in a pilot-scale water distribution systems

It is well known that model-building of chlorine decay in real water distribution systems is difficult because chlorine decay is influenced by many factors (e.g., bulk water demand, pipe-wall demand, piping material, flow velocity, and residence time). In this paper, experiments were run to investigate the kinetic model of chlorine decay and the formation model of trihalomethanes (THMs) in pilot-scale water distribution systems. Experimental results show that the rate constants of chlorine decay, including wall decay and bulk decay, increasing with temperature. Moreover, the kinetic model of chlorine decay and the formation model of THMs describe experiment data of pilot-scale water distribution systems. The effect of different piping material on chlorine decay and THMs formation were also investigated. The rate constants of chlorine decay are ranked in order: stainless steel pipe, ductile iron pipe, and last, polyethelene pipe because wall decay is the largest in stainless steel pipe than that in other piping material. Correspondingly, the rate of THMs formation follows the order of stainless steel pipe, ductile iron pipe, and last, polyethelene pipe because of less chlorine in bulk water reacting with the trihalomethane formation potential (THMFP).     

改性酚醛基炭泡沫的表面结构及脱硫脱硝

采用前驱体改性的方法,以CuCl2、FeCl2和MgCl2为改性剂,制备出改性酚醛泡沫,经炭化/活化得到改性酚醛基炭泡沫。研究了不同金属对酚醛基炭泡沫表面物理与化学特性的影响,并进行同时脱硫脱硝实验研究。通过研究发现,添加CuCl2的样品比添加FeCl2、MgCl2的样品的中孔孔容大接近10倍;比表面积和孔容是CFCu>CF0>CFFe>CFMg;金属改性剂主要以金属和金属氧化物的形式存在于酚醛基炭泡沫中,而表面其他官能团大体结构不变。经CuCl2、FeCl2和MgCl2改性后,脱硫效率分别提高了39%、11%和13%,脱硝效率分别提高了19%、10%和4%,其中以CuCl2改性的酚醛基炭泡沫的效率最高。     

Mo-N-TiO2光催化剂的制备、表征及其活性提高机制

以钼酸铵和氨水分别为钼源和氮源,采用溶胶-凝胶法制备了Mo-N-TiO2光催化剂,并对其进行了XRD、XPS和UV-visDRS表征。XRD结果表明,Mo、N共掺杂有效抑制了TiO2晶粒的生长,提高了TiO2由锐钛矿向金红石相的转变温度。UV-vis表明,Mo-N-TiO2光催化剂可见光吸收能力增强,吸收带边明显"红移",且钼酸铵添加量(相对TiO2)为0.5%的样品"红移"程度最大,最大吸收带边为550 nm。XPS分析结果表明,Mo取代了TiO2晶格中的部分Ti4+,以Mo6+形式存在的,而N以Ti—N及N—Ti—O形式存在。以罗丹明B为模型污染物,重点考察了钼酸铵添加量与焙烧温度对Mo-N-TiO2光催剂性能的影响。结果表明,400℃焙烧下、钼酸铵添加量为0.5%的样品催化活性最好。模拟太阳光下光照120min对罗丹明B的降解率达到96.8%,是纯TiO2的2.42倍。     

磁性海泡石吸附Cr(VI)特性及动力学

采用化学共沉淀法合成磁性海泡石,通过静态吸附实验研究磁性海泡石对Cr(Ⅵ)的吸附特性及其动力学。结果表明,磁性海泡石对Cr(Ⅵ)的吸附在90 min内即可达到平衡;体系的初始pH是影响磁性海泡石吸附Cr(Ⅵ)性能的重要因素;当废水中Cr(Ⅵ)的初始浓度为50 mg/L时,磁性海泡石的适宜投加量为10 g/L;随反应温度的升高,磁性海泡石对Cr(Ⅵ)的吸附量增加;温度为25、35和45℃时,磁性海泡石对Cr(Ⅵ)的饱和吸附量分别为3.32、3.72、4.08 mg/g;吸附动力学曲线可以用拟二级反应动力学模型拟合;内扩散和液膜扩散联合控制Cr(Ⅵ)在磁性海泡石上的吸附过程,其中内扩散的控速作用大于液膜扩散。     

有机酸土柱淋洗法修复重金属污染土壤

通过室内模拟实验,采用土柱淋洗方法,研究草酸、柠檬酸、乙酸和酒石酸溶液对某电镀厂附近土壤中重金属的去除效果。探讨了淋洗剂浓度、淋洗次数和淋洗时间等对淋洗效果的影响,研究草酸淋洗前后土壤中重金属形态的变化。结果表明,淋洗过程中铬的去除效果明显滞后于铜、锌和镍3种重金属离子。1 mol/L的草酸在土水比为1∶1,淋洗5h,淋洗4次的条件下可以达到最佳淋洗效果,Cu、Zn、Ni和Cr的去除率分别是99.6%、66.98%、88.7%和18.23%。     

脂肽类生物表面活性剂液体发酵条件的响应面优化

通过Plackett-Burman和Box-Behnken实验对解淀粉芽孢杆菌XZ-173液体发酵生产表面活性素进行了响应面优化研究。首先使用Plackett-Burman实验对影响表面活性素产量的17个因素进行显著性筛选,结果表明,MnSO4、CuSO4、温度和转速为显著性因素。再运用Box-Behnken实验对这4个显著因素的取值进一步优化,得到各因素优化后的数值分别为4.4 mg/L(MnSO4)、0.18 mg/L(CuSO4)、29℃(温度)和163 r/min(转速)。响应面分析结果表明:该菌株产生表面活性素的最佳培养基为:葡萄糖15 g/L,蛋白胨5 g/L,L-谷氨酸钠6 g/L,KH2PO40.8 g/L,MgSO40.4 g/L,KCl 0.4 g/L,酵母提取物3 g/L,L-苯丙氨酸2.5 mg/L,MnSO44.4 mg/L,CuSO40.18 mg/L,FeSO40.12 mg/L;最适培养条件:pH 7.5,温度29℃,转速163 r/min,接种量5%,装液量50 mL/250 mL,摇床培养36 h。在优化后的条件下,表面活性素实际产量为336 mg/L,实际实验结果与模型预测结果相一致。表面活性素采用HPLC技术分离,发现其在浓度仅为50 mg/L时EI24就可达到70%以上,反映了表面活性素优异的乳化活性以及广阔的应用前景。     

电解锰渣中锰的浸出条件及特征

采用水洗-酸解法回收电解锰渣中锰,探讨了清水量、酸量以及温度在不同阶段对锰浸(洗)出条件的影响,分析了回收锰的主要因素及浸出特征。实验结果表明,50 g电解锰渣经m渣∶m水=1∶10的清水水洗后,采用10%的硫酸在70℃的水浴温度下酸解2 h,Mn2+浸出量为1.673 g,回收率达到97.3%,而温度和酸度对锰离子的浸出影响明显,酸度调控可有效分离酸浸锰液中金属成分,为减少电解锰渣环境污染的同时,实现电解锰渣资源化利用。