深圳湾流域面源与截排溢流污染特征及其对水环境的影响

随着点源污染逐步得到有效控制,面源与截排溢流污染对水环境的胁迫日益突出。基于土地遥感数据、城市排水管网等资料,构建流域—海湾一体化水环境模型,探讨深圳湾流域面源与截排溢流污染特征及其对水环境的影响,研究表明：（1）雨季COD、NH₃-N和TP单位面积面源与截排溢流污染负荷分别为17.21 t/km²与10.21 t/km²、0.17 t/km²与0.69 t/km²、0.04 t/km²与0.07 t/km²;（2）面源与截排溢流污染时间上主要集中于大雨及以上等级降水较多的5月和8月,空间上主要分布在截排工程集中、下垫面面积较大且坡度较陡的深圳河、大沙河和新洲河流域;（3）面源与截排溢流水体COD、NH₃-N和TP浓度可达地表水V类标准的3.7倍、18.2倍和8.5倍;（4）雨季COD、NH₃-N和TP浓度高于旱季的区域分别超过深圳湾总面积的40%、60%和65%。     

双酚S在两种典型地带性土壤中的吸附/解吸行为研究

采用批平衡实验方法研究了双酚S（BPS）在两种典型地带性土壤中的吸附/解吸行为.结果表明,吸附动力学曲线符合拟二级动力学方程.吸附等温线呈非线性,且同时符合Freundlich和Langmuir方程.相比而言,BPS更易吸附在高有机质含量的黑土中,298 K反应温度下BPS在黑土和红壤上的最大吸附容量分别为497.8和156.6 mg·kg^-1.吸附到两种土壤中的BPS存在解吸滞后现象,这可能是由于BPS以化学吸附和微孔扩散的形式存在于土壤中的缘故.溶液pH与BPS在土壤中的吸附容量呈负相关关系,即中性形态的BPS比阴离子形态的BPS具有更高的吸附容量.与结构类似物双酚A（BPA）的吸附相比,BPS在土壤中的吸附量更低,因此具有更高的迁移能力,可能会引起更高的环境健康风险.本研究结果为了解BPS在土壤中的迁移规律提供了数据支持.     

北部湾南流江流域土地覆盖及生物多样性模拟

以北部湾独流入海河流南流江流域为研究对象,基于研究区2000年和2015年遥感数据解译的土地利用数据以及社会经济等数据,采用CLUE-S模型对未来2030年生态保护情景、自然增长情景以及粮食安全情景的土地利用格局进行了模拟预测,在此基础上采用InVEST模型对流域过去和未来不同情景的生物多样性进行了评估,探讨了流域生物多样性的生境质量和生境退化程度.结果表明：2000~2015年南流江流域建设用地、园地、水域和未利用地呈现出增加趋势,其中建设用地的增幅最大,而耕地和林地减幅最大.流域土地系统中共存在着34种土地网络转移流关系,上游存在24种,中游20种,下游28种,耕地与建设用地、耕地与林地以及林地与园地之间的转换占到流域总土地利用变化的70.74%.CLUE-S模型模拟未来土地利用的Kappa系数达到0.86,表明模型模拟未来情景的土地利用精度满足要求.2000年、2015年、2030年生态保护情景、2030年自然增长情景以及2030年粮食安全情景流域生境质量总得分和平均得分分别为866630,900357,921055,876231,865370和0.7457,0.7747,0.7925,0.7539,0.7466.2030年3种情景的中上游和下游地区生物多样性都呈现出不同程度的改善趋势,而中游地区则表现出退化趋势.     

pH值对亚硝酸盐氧化菌动力学及功能基因的影响

为探究pH值对亚硝酸盐氧化菌（NOB）活性动力学影响,本试验采用序批式活性污泥（SBR）反应器,以富含NOB的活性污泥为对象,基于Monod模型考察不同pH值对NOB活性动力学的影响并进行统计学分析.结果表明,Monod方程可较好地反映不同pH值条件下基质底物浓度对NOB比亚硝态氮氧化速率（SNiOR）的影响,且pH=7.0时动力学参数Ks为（6.167mg/L）,r_max为[1.134g/（g·d）],此时NOB活性最好.利用钟形经验模型进行非线性回归拟合,最大比降解速率（r_max）随pH值的增大呈钟形变化,本试验NOB的最佳pH值为（6.9±0.1）,其中r_max维持在r_opt一半以上的pH值范围（ω）为（3.26±0.4）.以亚硝酸盐氧化还原酶类基因（nxrA、nxrB）为引物,基于荧光定量PCR技术分析结果显示,在不同pH值条件下nxrA基因和nxrB基因拷贝数的变化趋势均与动力学参数（Ks、r_max）的规律一致,且nxrA和nxrB基因在系统的降解过程中起协同作用.     

Regulated emission characteristics of in-use LNG and diesel semi-trailer towing vehicles under real driving conditions using PEMS

On-road driving emissions of six liquefied natural gas(LNG) and diesel semi-trailer towing vehicles(STTVs) which met China Emission Standard IV and V were tested using Portable Emission Measurement System(PEMS) in northern China.Emission characteristics of these vehicles under real driving conditions were analyzed and proved that on-road emissions of heavy-duty vehicles(HDVs) were underestimated in the past.There were large differences among LNG and diesel vehicles, which also existed between China V vehicles and China IV vehicles.Emission factors showed the highest level under real driving conditions, which probably be caused by frequent acceleration, deceleration, and start-stop.NOx emission factors ranged from 2.855 to 20.939 g/km based on distance-traveled and 6.719–90.557 g/kg based on fuel consumption during whole tests, which were much higher than previous researches on chassis dynamometer.It was inferred from tests that the fuel consumption rate of the test vehicles had a strong correlation with NOx emission, and the exhaust temperature also affected the efficiency of Selected Catalytic Reduction(SCR) aftertreatment system, thus changing the NOx emission greatly.THC emission factors of LNG vehicles were 2.012–10.636 g/km, which were much higher than that of diesel vehicles(0.029–0.185 g/km).Unburned CH_4 may be an important reason for this phenomenon.Further on-road emission tests, especially CH_4 emission test should be carried out in subsequent research.In addition, the Particulate Number(PN) emission factors of diesel vehicles were at a very high level during whole tests, and Diesel Particulate Filter(DPF)should be installed to reduce PN emission.     

Bioassay: A useful tool for evaluating reclaimed water safety

Wastewater reclamation and reuse has been proved to be an effective way to relieve the fresh water crisis. However, toxic contaminants remaining in reclaimed water could lead to potential risk for reuse, and the conventional water quality standards have difficulty guaranteeing the safety of reclaimed water. Bioassays can vividly reflect the integrated biological effects of multiple toxic substances in water as a whole, and could be a powerful tool for evaluating the safety of reclaimed water. Therefore, in this study, the advantages and disadvantages of using bioassays for evaluating the safety of reclaimed water were compared with those of conventional water quality standards. Although bioassays have been widely used to describe the toxic effects of reclaimed water and treatment efficiency of reclamation techniques, a single bioassay cannot reflect the complex toxicity of reclaimed water, and a battery of bioassays involving multiple biological effects or in vitro tests with specific toxicity mechanisms would be recommended. Furthermore, in order to evaluate the safety of reclaimed water based on bioassay results, various methods including potential toxicology, the toxicity unit classification system, and a potential eco-toxic effects probe are summarized as well. Especially, some integrated ranking methods based on a bioassay battery involving multiple toxicity effects are recommended as useful tools for evaluating the safety of reclaimed water, which will benefit the promotion and guarantee the rapid development of the reclamation and reuse of wastewater.     

Dynamic nano-Ag colloids cytotoxicity to and accumulation by Escherichia coli: Effects of Fe3+, ionic strength and humic acid

Released Ag ions or/and Ag particles are believed to contribute to the cytotoxicity of Ag nanomaterials, and thus, the cytotoxicity and mechanism of Ag nanomaterials should be dynamic in water due to unfixed Ag particle:Ag⁺ ratios. Our recent research found that the cytotoxicity of PVP-Ag nanoparticles is attributable to Ag particles alone in 3 hr bioassays, and shifts to both Ag particles and released Ag⁺ in 48 hr bioassays. Herein, as a continued study, the cytotoxicity and accumulation of 50 and 100 nm Ag colloids in Escherichia coli were determined dynamically. The cytotoxicity and mechanisms of nano-Ag colloids are dynamic throughout exposure and are derived from both Ag ions and particles. Ag accumulation by E. coli is derived mainly from extracellular Ag particles during the initial 12 hr of exposure, and thereafter mainly from intracellular Ag ions. Fe³⁺ accelerates the oxidative dissolution of nano-Ag colloids, which results in decreasing amounts of Ag particles and particle-related toxicity. Na⁺ stabilizes nano-Ag colloids, thereby decreasing the bioavailability of Ag particles and particle-related toxicity. Humic acid (HA) binds Ag⁺ to form Ag⁺-HA, decreasing ion-related toxicity and binding to the E. coli surface, decreasing particle-related toxicity. HA in complex conditions showed a stronger relative contribution to toxicity and accumulation than Na⁺ or Fe³⁺. The results highlighted the cytotoxicity and mechanism of nano-Ag colloids are dynamic and affected by environmental factors, and therefore exposure duration and water chemistry should be seriously considered in environmental and health risk assessments.     

Revealing the changes of bacterial community from water source to consumers tap: A full-scale investigation in eastern city of China

This study profiled the bacterial community variations of water from four water treatment systems, including coagulation, sedimentation, sand filtration, ozonation-biological activated carbon filtration (O₃-BAC), disinfection, and the tap water after the distribution process in eastern China. The results showed that different water treatment processes affected the bacterial community structure in different ways. The traditional treatment processes, including coagulation, sedimentation and sand filtration, reduced the total bacterial count, while they had little effect on the bacterial community structure in the treated water (before disinfection). Compared to the traditional treatment process, O₃-BAC reduced the relative abundance of Sphingomonas in the finished water. In addition, ozonation may play a role in reducing the relative abundance of Mycobacterium. NaClO and ClO₂ had different effects on the bacterial community in the finished water. The relative abundance of some bacteria (e.g. Flavobacterium, Phreatobacter and Porphyrobacter) increased in the finished water after ClO₂ disinfection. The relative abundance of Mycobacterium and Legionella, which have been widely reported as waterborne opportunistic pathogens, increased after NaClO disinfection. In addition, some microorganisms proliferated and grew in the distribution system, which could lead to turbidity increases in the tap water. Compared to those in the finished water, the relative abundance of Sphingomonas, Hyphomicrobium, Phreatobacter, Rheinheimera, Pseudomonas and Acinetobacter increased in the tap water disinfected with NaClO, while the relative abundance of Mycobacterium increased in the tap water disinfected with ClO₂. Overall, this study provided the detailed variation in the bacterial community in the drinking water system.     

An investigation of changes in water quality throughout the drinking water production/distribution chain using toxicological and fluorescence analyses

Changes in water quality from source water to finished water and tap water at two conventional drinking water treatment plants(DWTPs) were monitored.Beside the routine water quality testing,Caenorhabditis elegans-based toxicity assays and the fluorescence excitation–emission matrices technique were also applied.Both DWTPs supplied drinking water that met government standards.Under current test conditions,both the investigated finished water and tap water samples exhibited stronger lethal,genotoxic and reprotoxic potential than the relative source water sample,and the tap water sample was more lethal but tended to be less genotoxic than the corresponding finished water sample.Meanwhile,the nearly complete removal of tryptophan-like substances and newly generated tyrosine-like substances were observed after the treatment of drinking water,and humic-like substances were identified in the tap water.Based on these findings,toxic pollutants,including genotoxic/reproductive toxicants,are produced in the drinking water treatment and/or distribution processes.Moreover,further studies are needed to clarify the potentially important roles of tyrosine-like and humic-like substances in mediating drinking water toxicity and to identify the potential sources of these contaminants.Additionally,tryptophan-like fluorescence may be adopted as a useful parameter to monitor the treatment performance of DWTPs.Our observations provided insights into the importance of utilizing biotoxicity assays and fluorescence spectroscopy as tools to complement the routine evaluation of drinking water.     

Mechanism and catalytic performance for direct dimethyl ether synthesis by CO2 hydrogenation over CuZnZr/ferrierite hybrid catalyst

Direct synthesis of dimethyl ether(DME) by CO_2 hydrogenation has been investigated over three hybrid catalysts prepared by different methods:co-precipitation,sol-gel,and solid grinding to produce mixed Cu,ZnO,ZrO_2 catalysts that were physically mixed with a commercial ferrierite(FER) zeolite.The catalysts were characterized by N_2 physisorption,X-ray diffraction(XRD),transmission electron microscopy(TEM),X-ray photoelectron spectroscopy(XPS),temperature programmed desorption of CO_2(CO_2-TPD),temperature programmed desorption of NH_3(NH_3-TPD),and temperature programmed H2 reduction(H_2-TPR).The results demonstrate that smaller CuO and Cu crystallite sizes resulting in better dispersion of the active phases,higher surface area,and lower reduction temperature are all favorable for catalytic activity.The reaction mechanism has been studied using in situ diffuse reflectance infrared Fourier transform spectroscopy(DRIFTS).Methanol appears to be formed via the bidentate-formate(b-HCOO) species undergoing stepwise hydrogenation,while DME formation occurs from methanol dehydration and reaction of two surface methoxy groups.