螺、蚌对污水处理厂再生水环境的改善稳定作用

通过选用昆明市第五污水处理厂的一级A标出水和水处理厂外排污泥作为静态实验环境,研究不同混养密度下铜锈环棱螺、椭圆背角无齿蚌对污水处理厂再生水环境的净化性能,筛选出净化效果较好的放养密度。结果表明:放养30 d,铜锈环棱螺、椭圆背角无齿蚌对污水处理厂再生水环境的水质、底质均有一定的净化作用,扣减空白对照影响,水中COD、TP、NH3-N及底泥有机质平均去除率分别为22.26%、26.10%、25.60%和25.69%,底泥厚度平均减少3.8 cm;与对照相比,放养螺蚌45 d内水均能清澈见底,透明度均>70 cm,能明显稳定水体透明度,改善水环境。综合螺蚌生长适应性和净化效果考虑:污水处理厂再生水静态环境中,螺蚌混养密度应≤3 000 g/m3,在2 000～2 500 g/m3为宜,其中铜锈环棱螺的最适放养密度在400 g/m3,椭圆背角无齿蚌为1 600～2 100 g/m3。     

核桃壳粉对水溶液中Pb2＋的吸附

实验通过间歇吸附方式研究了核桃壳粉对水溶液中Pb^2＋的吸附特性,探讨了核桃壳粉粒径及用量、溶液pH、Pb^2＋初始浓度等参数对吸附的影响,并讨论了吸附过程的热力学和动力学特征。结果表明,核桃壳粉对Pb^2＋吸附的最佳pH为5．0,去除率随吸附剂粒径的减小、用量的增加、Pb^2＋初始浓度的减小而增加。优化实验条件下,0～0．3mm15g／L的吸附剂在298K时,对pH=5的50mL50mg／LPb^2＋溶液的去除率达96．98％。核桃壳粉对Pb^2＋的吸附等温线符合Sips模型,在283、293和303K的最大吸附量分别为18．25、18．27和20．94mg／g。吸附过程是放热的、混乱度减小的自发过程,且符合准二级动力学模型。吸附速率常数随温度升高而减小,在293和303K时分别在90和120min基本达到平衡。结合FTIR和SEM手段发现核桃壳对Pb^2＋的吸附以物理吸附为主,同时包括离子交换、螯合等化学吸附以及颗粒内扩散步骤,是一个复杂的过程。     

某矿区土壤和地下水重金属污染调查与评价

为了解湘南某矿区土壤和地下水重金属污染状况,对该矿区东河流域附近重金属污染源进行了调查,同时,对地下水和土壤样品进行了采样分析,结果表明：（1）该矿区东河流域附近的主要污染源有18个,其中有色金属选厂、尾矿库、采矿场和冶炼厂是排放重金属较多的污染源;（2）20个采样点中土壤重金属Pb、Cd、Zn、As和Hg大部分超过国家土壤环境质量标准（GB15618-1995）,综合污染指数P综〉1,该矿区主要的重金属污染元素为Cd、As和Hg,且土壤中Cd、Zn和As的含量两两之间存在着极显著的正线性相关关系;（3）重金属元素在土壤中的纵向迁移不明显,该矿区附近20个采样点的地下水并未受到污染,综合污染指数P综〈1。20个采样点地下水Pb、Cd、Zn、As、Hg浓度均能达到地下水质量标准（GB／T14848．9）中的Ⅲ类标准。     

铈改性Al_2O_3担载Pd催化剂的CO氧化性能研究

浸渍法制备了Al2O3+CeO2为载体的Pd催化剂,对制备中各因素对催化剂效果的影响作了初步研究.考察了活性组分含量与催化荆性能的关系以及焙烧温度、水蒸气对催化剂活性的影响.结果表明,稀土Ce元素的存在使催化剂的性能得到明显改善.制备过程中焙烧步骤对催化剂的活性影响很大,催化剂制备必须高于600 ℃焙烧.     

Spatial character of polychlorinated biphenyls from soil and respirable particulate matter in Taiyuan, China

As one of China’s great metropolises, Taiyuan is affected by heavy chemical industry and manufacture of chemical products, and faces pollution from polychlorinated biphenyls (PCBs). Therefore, this study was conducted to determine the PCB concentrations in various environmental media in Taiyuan. We collected 15 soil samples, 34 respirable particulate matter (PM) samples (17 of PM_2.5 and 17 of PM₁₀) from urban areas of Taiyuan, and measured a total of 144 PCB congeners (including some coeluting PCB congeners). The total PCB concentrations were 51–4.7 × 10³ pg g⁻¹ in soil, 27–1.4 × 10² pg m⁻³ in PM_2.5 and 16–1.9 × 10² pg m⁻³ in PM₁₀. Of the PCB homologues, the dominant PCBs detected in the various media were all tri-CBs. Soil was relatively the most polluted media. Furthermore, principal-component analysis revealed that the major PCB source in Taiyuan may be associated with the main commercial PCB through long-range transmission. Toxic equivalency (TEQ) concentrations (based on ten dioxin-like PCBs) ranged from N.D. to 5.9 × 10⁻³ pg-WHO TEQ g⁻¹ in soil, 2.0 × 10⁻⁴–3.4 × 10⁻³ pg-WHO TEQ m⁻³ and 1.0 × 10⁻⁴–1.2 × 10⁻³ pg-WHO TEQ m⁻³ in PM_2.5 and PM₁₀, respectively. In previous studies, PCBs were not a severe component of contaminant in Taiyuan; however, this study suggested there is a potential threat of human exposure to PCBs for residents of Taiyuan.     

Part V—sorption of pharmaceuticals and personal care products

Background, aim, and scope  Pharmaceuticals and personal care products (PPCPs) including antibiotics, endocrine-disrupting chemicals, and veterinary pharmaceuticals are emerging pollutants, and their environmental risk was not emphasized until a decade ago. These compounds have been reported to cause adverse impacts on wildlife and human. However, compared to the studies on hydrophobic organic contaminants (HOCs) whose sorption characteristics is reviewed in Part IV of this review series, information on PPCPs is very limited. Thus, a summary of recent research progress on PPCP sorption in soils or sediments is necessary to clarify research requirements and directions. Main features  We reviewed the research progress on PPCP sorption in soils or sediments highlighting PPCP sorption different from that of HOCs. Special function of humic substances (HSs) on PPCP behavior is summarized according to several features of PPCP–soil or sediment interaction. In addition, we discussed the behavior of xenobiotic chemicals in a three-phase system (dissolved organic matter (DOM)–mineral–water). The complexity of three-phase systems was also discussed. Results  Nonideal sorption of PPCPs in soils or sediments is generally reported, and PPCP sorption behavior is relatively a more complicated process compared to HOC sorption, such as the contribution of inorganic fractions, fast degradation and metabolite sorption, and species-specific sorption mechanism. Thus, mechanistic studies are urgently needed for a better understanding of their environmental risk and for pollution control. Discussion  Recent research progress on nonideal sorption has not been incorporated into fate modeling of xenobiotic chemicals. A major reason is the complexity of the three-phase system. First of all, lack of knowledge in describing DOM fractionation after adsorption by mineral particles is one of the major restrictions for an accurate prediction of xenobiotic chemical behavior in the presence of DOM. Secondly, no explicit mathematical relationship between HS chemical–physical properties, and their sorption characteristics has been proposed. Last but not least, nonlinear interactions could exponentially increase the complexity and uncertainties of environmental fate models for xenobiotics. Discussion on proper simplification of fate modeling in the framework of nonlinear interactions is still unavailable. Conclusions  Although the methodologies and concepts for studying HOC environmental fate could be adopted for PPCP study, their differences should be highly understood. Prediction of PPCP environmental behavior needs to combine contributions from various fractions of soils or sediments and the sorption of their metabolites and different species. Recommendations and perspectives  More detailed studies on PPCP sorption in separated soil or sediment fractions are needed in order to propose a model predicting PPCP sorption in soils or sediments based on soil or sediment properties. The information on sorption of PPCP metabolites and species and the competition between them is still not enough to be incorporated into any predictive models.     

Cation exchange in a glacial till drumlin at a road salt storage facility

At a former wood preservation plant severely contaminated with coal tar oil, in situ bulk attenuation and biodegradation rate constants for several monoaromatic (BTEX) and polyaromatic hydrocarbons (PAH) were determined using (1) classical first order decay models, (2) Michaelis–Menten degradation kinetics (MM), and (3) stable carbon isotopes, for o-xylene and naphthalene. The first order bulk attenuation rate constant for o-xylene was calculated to be 0.0025 d^− 1 and a novel stable isotope-based first order model, which also accounted for the respective redox conditions, resulted in a slightly smaller biodegradation rate constant of 0.0019 d^− 1. Based on MM-kinetics, the o-xylene concentration decreased with a maximum rate of k_max = 0.1 µg/L/d. The bulk attenuation rate constant of naphthalene retrieved from the classical first order decay model was 0.0038 d^− 1. The stable isotope-based biodegradation rate constant of 0.0027 d^− 1 was smaller in the reduced zone, while residual naphthalene in the oxic part of the plume further downgradient was degraded at a higher rate of 0.0038 d^− 1. With MM-kinetics a maximum degradation rate of k_max = 12 µg/L/d was determined. Although best fits were obtained by MM-kinetics, we consider the carbon stable isotope-based approach more appropriate as it is specific for biodegradation (not overall attenuation) and at the same time accounts for the dominant electron-accepting process. For o-xylene a field based isotope enrichment factor ε_field of − 1.4 could be determined using the Rayleigh model, which closely matched values from laboratory studies of o-xylene degradation under sulfate-reducing conditions.     

Adsorption of Pb(II) on variable charge soils amended with rice-straw derived biochar

Two Ultisols and one Oxisol from tropical regions of southern China were incubated with rice straw biochar to investigate the effect of biochar on their surface charge and Pb(II) adsorption using batch methods. The incorporation of biochar induced a remarkable increase in soil cation exchange capacity after 30 d of incubation. The incorporation of biochar significantly increased the adsorption of Pb(II) by these variable charge soils; the enhancement of adsorption of Pb(II) by these soils increased with the addition level of biochar. Adsorption of Pb(II) involved both electrostatic and non-electrostatic mechanisms; however, biochar mainly increased Pb(II) adsorption through the non-electrostatic mechanism via the formation of surface complexes between Pb²⁺ and functional groups on biochar. There was greater enhancement of biochar on the non-electrostatic adsorption of Pb(II) by the variable charge soils at relatively low pH. Therefore, the incorporation of biochar decreased the activity and availability of Pb(II) to plants through increased non-electrostatic adsorption of Pb(II) by acidic variable charge soils.     

Subcellular distribution and toxicity of cadmium in Potamogeton crispus L

The submerged macrophyte Potamogeton crispus L. was subjected to varying doses of cadmium (0, 20, 40, 60 and 80 μM) for 7 d, and the plants were analyzed for subcellular distribution of Cd, accumulation of mineral nutrients, photosynthesis, oxidative stress, protein content, and ultrastructural distribution of calcium (Ca). Leaf fractionation by differential centrifugation indicated that 48-69% of Cd was accumulated in the cell wall. At all doses of Cd, the levels of Ca and B rose and the level of Mn fell; the levels of Fe, Mg, Zn, Cu, Mo, and P rose initially only to decline later. Exposure to Cd caused oxidative stress as evident by increased content of malondialdehyde and decreased contents of chlorophyll and protein. Photosynthetic efficiency, as indicated by the quenching of chlorophyll a fluorescence (Fv/Fm, Fo and Fm), decreased significantly, the extent of decrease being directly proportional to the concentration of Cd. Increased amounts of precipitates of calcium were noticed in the treated plants, located either outside the cell membrane or in chloroplasts, mitochondria, the nucleus, and the cytoplasm whereas control plants showed small deposits of the precipitates around surface of the vacuole membrane and in the intercellular space but rarely in the cytoplasm. Photosynthetic efficiency and oxidative stress could be used as indicators of physiological end-points in determining the extent of Cd phytotoxicity.     

Ozonation as an advanced oxidant in treatment of bamboo industry wastewater

The present study employed ozonation process to treat the bamboo industry wastewater (BIWW). The impact of ozone dosage and initial organic concentration on color, COD and TOC removal rates were studied along with characterization of the major organics in raw and treated wastewater. The results suggested the ozone dosage of 3.15 g h⁻¹ (concentration 52.5 mg L⁻¹) was suitable for the treatment. After 25 min ozonation of 1 L raw wastewater, the color, COD and TOC removal efficiencies were 95%, 56% and 40%, respectively, with an influent COD concentration of 835 mg L⁻¹. The ratio of kg O₃ kg⁻¹ COD at 3.15 g h⁻¹ was 2.8 (<3), revealing that ozonation was a cost effective process for tertiary treatment of BIWW. Longer oxidization time was required to achieve similar results for raw wastewater with higher COD concentration. The chromatogram from gel permeation chromatography revealed that ozonation resulted in the breakdown of high molecular weight compounds into lower molecular weight components but could not completely mineralize the organic matter. The majority of these compounds were identified in both raw and ozonated samples via GC-MS analysis. In addition to ester derivatives as the main intermediates of ozonation, 1-chloroctadecane, methyl stearate, benzophenone and α-cyperone were identified as the by-products of ozonation.