Biodegradation of high molecular weight PAHs using isolated yeast mixtures: application of meta-genomic methods for community structure analyses

Bioaugmentation for the removal of polyaromatic hydrocarbons (PAHs) from wastewater using bacteria and yeasts is considered environment-friendly and a cost-effective technique. The effectiveness of this biodegradation system depends on the stability of inoculated microorganisms and the availability of nutrients. This study is aimed to investigate the removal of high molecular weight (HMW)-PAHs from biologically treated produced water using different biological systems. Three systems, inoculated with activated sludge (AS), the mixture of five yeast strains (MY), and the mixture of AS and the five yeast strains (SY), respectively, were constructed, and their performance for the removal of HMW-PAHs was compared over 10 weeks. The effluent of the biologically treated produced water from an oilfield was used as the influent after chrysene and benzo(a)pyrene were spiked as HMW-PAHs. Polymerase chain reaction-based denaturing gradient gel electrophoresis (PCR-DGGE) and fluorescent in situ hybridization (FISH) techniques were used to examine the changes in the structures and abundances of the bacterial and yeast communities in these three systems. Only SY and MY systems were capable to remove chrysene (90.7 % and 98.5 %, respectively) and benzo(a)pyrene (80.7 % and 95.2 %, respectively). PCR-DGGE analysis confirmed that all of the five yeast strains inoculated remained in the SY and MY systems, while FISH results showed that the relative abundance of yeast in the SY and MY systems (10.6 % to 21.9 %, respectively) were significantly higher than AS system (2.3 % to 7.8 %, respectively). The relative abundances of the catechol 2,3-dioxygenase (C23O) indicated that the copy number ratios of benzene ring cleavage gene C23O in the yeast amended systems were much higher than that in the AS system. In this study, all of the three systems were effective in removing the low molecular weight (LMW)-PAHs, while HMW-PAHs including chrysene and benzo(a)pyrene were efficiently removed by MY and SY systems, not by AS system. The high HMW-PAHs removal in the MY and SY bioaugmentation systems possibly attributed to the inoculation of the mixed yeast culture. By combining the PCR-DGGE results with the FISH analyses, it was found that yeast probably consisting mainly of the five inoculated strains inhabited in the two bioaugmentation systems as a dominant population. The relatively higher performance of the SY system might be attributed to the suspended growth type which permitted a more efficient contact between microbial cells and contaminants. The bioaugmentation systems (SY and MY) were successfully established by inoculating with five nonindigenous yeast strains and demonstrated high performance in removal of HMW-PAHs.     

Arsenic accumulation and speciation in the submerged macrophyte Ceratophyllum demersum L.

Introduction

Ceratophyllum demersum L. is a widespread submerged macrophyte in aquatic environments.

Methods

Simulation experiments were conducted in the laboratory to investigate arsenic (As) accumulation, speciation, and efflux of C. demersum exposed to arsenate and arsenite solutions.

Results

Plant shoots showed a significant accumulation of As with a maximum of 862 and 963???g?As?g^?1 dry weight after 4?days of exposure to 10???M arsenate and arsenite, respectively. Regardless of whether arsenate or arsenite was supplied to the plants, arsenite was the predominant species in plant shoots. Furthermore, a dramatically higher influx rate of arsenate compared with arsenite was observed in C. demersum exposed to As solutions without the addition of phosphate (P). Arsenate uptake was considerably inhibited by P in this study, suggesting that arsenate is taken up by C. demersum via the phosphate transporters. However, arsenite uptake was unaffected by P and markedly reduced in the presence of glycerol and antimonite (Sb), indicating arsenite shares the aquaporin transport pathway. In addition, C. demersum rapidly reduces arsenate to arsenite in the shoot of the plant and extrudes most of them (>60?%) to the external solutions. The efflux of arsenite was much higher than that of arsenate; the former is supposed to be both active and passive processes, and the latter through passive leakage.

Conclusion

C. demersum is a strong As accumulator and an interesting model plant to study As uptake and metabolism due to the lack of a root-to-shoot translocation barrier.     

垃圾渗滤液发酵产氢和产甲烷特性研究

以实际垃圾渗滤液作为厌氧发酵基质,研究了初始pH为7.0、中温(37℃)条件下的发酵产氢、产甲烷特性。结果表明,利用垃圾渗滤液作为基质发酵产氢或甲烷时,氢气的最大累积产量为24.33mL(以每克COD计,下同),甲烷的最大累积产量为91.59mL,产氢发酵在初期存在明显的迟滞期,但是产甲烷发酵不存在明显迟滞期;产氢发酵的液相末端产物中含有大量的挥发性有机酸和乙醇,乙醇、乙酸、丁酸质量浓度分别为487.23、1 175.21、1 225.78mg/L,相比产氢发酵,产甲烷发酵的液相末端产物中乙醇、乙酸、丁酸质量浓度均较低,分别为256.38、106.73、107.42mg/L;产甲烷发酵的最终pH是6.32,接近中性,而产氢发酵的最终pH为4.21,呈明显酸性;产甲烷发酵对COD的去除率(41.78%)高于产氢发酵对COD的去除率(32.14%),可能是产氢发酵液相末端产物中的乙酸能被产甲烷菌利用,而被进一步降解。     

3种植物对Cd污染农田土壤的修复效果比较试验研究

通过盆栽试验研究了3种植物三叶鬼针草(Bidens pilosa L.)、紫茉莉(Mirabilis Jalapa)、中华景天(Sedum polytrich-oides)对上海地区2种质量浓度(1.2、12.0mg/kg)Cd污染农田土壤的修复效果,以探索其在上海地区Cd污染农田土壤修复中应用的可行性。结果表明:2种浓度下,三叶鬼针草对土壤Cd去除效果均最佳,1.2mg/kg处理下盆中土壤Cd质量浓度由原来的1.249 9mg/kg下降到0.861 7mg/kg,降低0.388 2mg/kg,Cd去除率为31.06%;12.0mg/kg处理下三叶鬼针草盆中土壤Cd质量浓度由原来的12.033 2mg/kg下降到10.020 6mg/kg,降低2.012 6mg/kg,Cd去除率为16.73%;紫茉莉和中华景天相比较而言,修复效果均较差。在2种浓度下,3种植物地上部分生物量排序均为三叶鬼针草>中华景天>紫茉莉。因此,建议将三叶鬼针草作为上海地区Cd污染农田土壤修复的优选植物。     

Enhanced mercuric chloride adsorption onto sulfur-modified activated carbons derived from waste tires

A number of activated carbons derived from waste tires were further impregnated by gaseous elemental sulfur at temperatures of 400 and 650 degrees C, with a carbon and sulfur mass ratio of 1:3. The capabilities of sulfur diffusing into the micropores of the activated carbons were significantly different between 400 and 650 degrees C, resulting in obvious dissimilarities in the sulfur content of the activated carbons. The sulfur-impregnated activated carbons were examined for the adsorptive capacity of gas-phase mercuric chloride (HgC1) by thermogravimetric analysis (TGA). The analytical precision of TGA was up to 10(-6) g at the inlet HgCl2 concentrations of 100, 300, and 500 microg/m3, for an adsorption time of 3 hr and an adsorption temperature of 150 degrees C, simulating the flue gas emitted from municipal solid waste (MSW) incinerators. Experimental results showed that sulfur modification can slightly reduce the specific surface area of activated carbons. High-surface-area activated carbons after sulfur modification had abundant mesopores and micropores, whereas low-surface-area activated carbons had abundant macropores and mesopores. Sulfur molecules were evenly distributed on the surface of the inner pores after sulfur modification, and the sulfur content of the activated carbons increased from 2-2.5% to 5-11%. After sulfur modification, the adsorptive capacity of HgCl2 for high-surface-area sulfurized activated carbons reached 1.557 mg/g (22 times higher than the virgin activated carbons). The injection of activated carbons was followed by fabric filtration, which is commonly used to remove HgCl2 from MSW incinerators. The residence time of activated carbons collected in the fabric filter is commonly about 1 hr, but the time required to achieve equilibrium is less than 10 min. Consequently, it is worthwhile to compare the adsorption rates of HgCl2 in the time intervals of < 10 and 10-60 min.     

苦土和氧化镁处理氮磷废水的对比研究

分别采用苦土、纯氧化镁为沉淀剂对模拟高浓度氮磷废水(N/P=0.8)进行了脱氮除磷研究,比较了沉淀剂投加量、pH对2种沉淀剂处理氮磷废水的影响,对沉淀产物进行XRD分析,并进行了经济效益比较。结果表明,pH是影响2种沉淀剂处理氮磷废水的主要因素,随着pH的增加,脱氮除磷效果提高,在平衡pH为9～10之间时氮磷处理效果最佳,pH继续增加,由于磷酸镁沉淀的形成使得氨氮去除率降低。此外,处理相同的废水,苦土的最佳投加量要大于纯氧化镁,但是经济效益比较结果表明,以苦土为沉淀剂处理氮磷废水可大大降低处理成本。     

菱镁矿尾矿制备高活性MgO的性能表征

菱镁矿尾矿经预处理后,在一定条件下制备高活性MgO。使用热重-差热分析仪,分析菱镁矿尾矿的分解温度,应用X射线衍射、SEM分析不同煅烧温度、保温时间对MgO晶体结构的影响,并根据Scherrer公式计算MgO晶粒的尺寸。通过电导率仪测定MgO水化电导率,分析不同条件下的MgO活性,探讨煅烧温度、保温时间、颗粒细度与MgO活性之间的关系。结果发现:煅烧温度在1 050℃,保温时间60 min时,菱镁尾矿完全分解,MgO活性最佳;煅烧温度越高,保温时间越长,MgO的活性越差;MgO颗粒细度越小,活性越高。     

外源Cd对不同利用方式红壤脲酶活性的影响

采用室内培养实验,通过将外源Cd添加到同一母质、全镉含量相近的不同利用方式的红壤中(林地、水稻土和菜园土),研究了外源Cd污染对不同利用方式红壤脲酶活性的影响。结果表明:整个培养过程中,Cd污染对3种红壤脲酶活性都有抑制作用,且随重金属浓度的增强而增强。同剂量Cd污染对3种红壤脲酶活性的抑制效应不同,大小为林地>水稻土>菜园土。实验设定的Cd处理水平下,对林地、水稻土和菜园土脲酶活性产生显著抑制作用(p<0.05)的Cd浓度分别为5、30和50 mg/kg土。     

玉米深加工废水的混凝实验

在室温条件下,分别选用聚合氯化铝(PAC)、聚合氯化铝铁(PAFC)及三氯化铁(FeCl3)对玉米深加工废水进行混凝实验。综合考虑各种混凝剂对磷、COD以及SS的去除效果,最终选取PAC作为混凝剂。采用PAC和聚丙烯酰胺(PAM)作为复合混凝剂,对其去除效果做进一步研究,并确定了最佳投加量及pH值。实验结果表明,在PAC投加量25mg/L,PAM投加量0.5 mg/L,pH为8条件下,混凝效果最佳。磷、COD、SS去除率可分别达到90.1%、53.3%和88.2%,对应的出水质量浓度分别为0.41、26.8和2 mg/L。     

纳米生态基对水产养殖污水的处理效果

采用三因子四水平的正交设计,实验研究了纳米生态基在不同温度、溶解氧和水力停留时间下对水产养殖污水的处理效果,确定了纳米生态基处理养殖污水的最佳条件。结果表明,含氨氮和亚硝氮浓度较高的模拟养殖污水用纳米生态基挂膜,所需时间约为22 d。纳米生态基对氨氮的去除效果明显,平均去除率达到93.5%。对氨氮去除率的影响程度,水力停留时间>温度>溶解氧。当温度为30℃,DO为5.43 mg/L,HRT为0.33 h时,纳米生态基对氨氮的处理能力最佳,去除率达到94.6%。纳米生态基对亚硝氮的平均去除率为69.3%。对亚硝氮去除率的影响程度,水力停留时间>溶解氧>温度。当温度为21℃,DO为6.40 mg/L,HRT为0.33 h时,纳米生态基对亚硝氮的处理能力最佳,去除率为71.5%。纳米生态基处理养殖污水的最佳条件:温度为30℃,DO为6.40 mg/L,HRT为0.33 h。