北部湾南流江流域土地覆盖及生物多样性模拟

以北部湾独流入海河流南流江流域为研究对象,基于研究区2000年和2015年遥感数据解译的土地利用数据以及社会经济等数据,采用CLUE-S模型对未来2030年生态保护情景、自然增长情景以及粮食安全情景的土地利用格局进行了模拟预测,在此基础上采用InVEST模型对流域过去和未来不同情景的生物多样性进行了评估,探讨了流域生物多样性的生境质量和生境退化程度.结果表明：2000~2015年南流江流域建设用地、园地、水域和未利用地呈现出增加趋势,其中建设用地的增幅最大,而耕地和林地减幅最大.流域土地系统中共存在着34种土地网络转移流关系,上游存在24种,中游20种,下游28种,耕地与建设用地、耕地与林地以及林地与园地之间的转换占到流域总土地利用变化的70.74%.CLUE-S模型模拟未来土地利用的Kappa系数达到0.86,表明模型模拟未来情景的土地利用精度满足要求.2000年、2015年、2030年生态保护情景、2030年自然增长情景以及2030年粮食安全情景流域生境质量总得分和平均得分分别为866630,900357,921055,876231,865370和0.7457,0.7747,0.7925,0.7539,0.7466.2030年3种情景的中上游和下游地区生物多样性都呈现出不同程度的改善趋势,而中游地区则表现出退化趋势.     

pH值对亚硝酸盐氧化菌动力学及功能基因的影响

为探究pH值对亚硝酸盐氧化菌（NOB）活性动力学影响,本试验采用序批式活性污泥（SBR）反应器,以富含NOB的活性污泥为对象,基于Monod模型考察不同pH值对NOB活性动力学的影响并进行统计学分析.结果表明,Monod方程可较好地反映不同pH值条件下基质底物浓度对NOB比亚硝态氮氧化速率（SNiOR）的影响,且pH=7.0时动力学参数Ks为（6.167mg/L）,r_max为[1.134g/（g·d）],此时NOB活性最好.利用钟形经验模型进行非线性回归拟合,最大比降解速率（r_max）随pH值的增大呈钟形变化,本试验NOB的最佳pH值为（6.9±0.1）,其中r_max维持在r_opt一半以上的pH值范围（ω）为（3.26±0.4）.以亚硝酸盐氧化还原酶类基因（nxrA、nxrB）为引物,基于荧光定量PCR技术分析结果显示,在不同pH值条件下nxrA基因和nxrB基因拷贝数的变化趋势均与动力学参数（Ks、r_max）的规律一致,且nxrA和nxrB基因在系统的降解过程中起协同作用.     

粗放型绿色屋顶基质层对降雨出流水质影响

为研究粗放型绿色屋顶基质层对雨水出流N、P、COD和SS淋失的影响,根据华中地区降雨强度和水质实际情况,构建了3种不同基材配方的绿色屋顶基质层,在9场模拟暴雨下进行绿色屋顶的基质出流水质监测。结果表明:本试验各绿色屋顶设施对TN、NH₄+-N、NO₃--N和SS都有较好的削减作用,但对TP和PO₄3--P淋失现象明显,绿色屋顶的出流中以颗粒态P和溶解态N为主;去除出流中SS,对净化COD效果显著;生物炭的添加对出流污染物有明显的控制作用,能有效缓解降雨初期污染物浓度高的问题,同时能显著增加植物地上部生物量;厚度为5 cm的绿色屋顶出流水中N和COD较10 cm厚度低,但其SS出流平均浓度偏高,且植物后期不能维持良好的长势。粗放型绿色屋顶设施运行稳定后截污效应良好,具有较高的可行性和广阔的应用前景。     

基于洪涝风险分析的纽约市城市绿地规划设计及其对中国的启示

1968年美国开始推行洪涝保险计划,不断完善对洪涝风险的研究,并逐步形成了一套相对完善的洪泛区管理体系,而洪涝风险分析在洪涝保险、城市规划、土地开发、应急管理等领域广泛应用。纽约市在经历了多次飓风侵害,尤其是2012年飓风桑迪（Sandy）之后,意识到城市绿地在极端暴雨事件时对雨洪调蓄的重要作用,经过持续的研究实践,提出了基于洪涝风险分析的城市绿地规划设计要求。基于总结美国纽约市在飓风桑迪影响下对洪涝风险图的调整,及其对城市绿地规划设计相关要求,提出其对我国洪涝风险管控及城市绿地规划设计的启示。     

土壤环境中微塑料的污染现状及其影响研究进展

微塑料作为一种持久性污染物,对土壤生态系统具有严重影响,土壤中微塑料的污染已愈加受到国内外学者的广泛关注。当前关于土壤环境中微塑料的研究较少,针对当前土壤中微塑料的来源、分布、降解迁移、生态效应及污染防治等方面进行综述。主要包括以下几个方面:1）概括土壤生态系统中微塑料的来源、分布特点和迁移降解规律,确定了土壤环境中微塑料的赋存状态;2）总结土壤生态系统中微塑料与其他污染物的复合效应;3）分析了微塑料对土壤理化性质、动物、植物、微生物的影响,并揭示了微塑料对于土壤生态系统的影响;4）根据土壤微塑料的分布特点、降解迁移及生态效应提出污染防治措施。最后,对今后土壤微塑料的研究重点进行了展望。     

锐钛矿型二氧化钛的低温合成及其吸附除氟性能的研究

通过水解法在50℃低温条件下合成了锐钛矿型TiO₂,使用XRD、FT-IR、BET等方法对TiO₂进行了表征,并研究其对水中氟离子的吸附行为。结果表明:所合成锐钛矿型TiO₂比表面积达到278.93 m2/g,常温下对氟离子的最大吸附量为30.02 mg/g。吸附过程符合Langmuir等温线模型和准一级动力学模型,是自发性的吸热过程,吸附机理为静电吸引。     

预处理对园林垃圾混合物料联合厌氧发酵的影响

采用超声、微波及碱热预处理技术强化园林垃圾、厨余垃圾与果蔬垃圾联合厌氧发酵产气性能,并以未进行预处理的实验组作为对照。结果表明:4组实验pH值在2 d内迅速降低至7.24~7.45,反应后期可稳定在7.7~8.0,表明厌氧消化系统有较强的稳定性。挥发性脂肪酸（volatile fatty acids,VFA）浓度在第2~4天内达到最大值。乙酸和丙酸是4组实验中VFA的主要成分,两者比例之和在70%以上。VFA浓度在第13天后降低到500 mg/L以下,且以乙酸为主。氨氮（TAN）浓度在前4 d内出现一定波动,随后逐渐升高至2190~2410 mg/L。游离氨氮（FAN）浓度呈先降低后增加趋势,并在第13天后逐渐趋于稳定,为144~209 mg/L。沼气中甲烷比例在第2天后均超过50%,并在第11~12天时达到最大值61.4%~63.8%。修正的Gomperts模型模拟结果表明:预处理技术可缩短反应体系厌氧产沼的适应时间,提高前期产气速率。除此之外,超声预处理与碱热预处理可显著提高基质甲烷产率,由未处理时的396 mL/g分别提高到601,536 mL/g,而微波预处理使得反应体系甲烷产量略有降低。     

Regulated emission characteristics of in-use LNG and diesel semi-trailer towing vehicles under real driving conditions using PEMS

On-road driving emissions of six liquefied natural gas(LNG) and diesel semi-trailer towing vehicles(STTVs) which met China Emission Standard IV and V were tested using Portable Emission Measurement System(PEMS) in northern China.Emission characteristics of these vehicles under real driving conditions were analyzed and proved that on-road emissions of heavy-duty vehicles(HDVs) were underestimated in the past.There were large differences among LNG and diesel vehicles, which also existed between China V vehicles and China IV vehicles.Emission factors showed the highest level under real driving conditions, which probably be caused by frequent acceleration, deceleration, and start-stop.NOx emission factors ranged from 2.855 to 20.939 g/km based on distance-traveled and 6.719–90.557 g/kg based on fuel consumption during whole tests, which were much higher than previous researches on chassis dynamometer.It was inferred from tests that the fuel consumption rate of the test vehicles had a strong correlation with NOx emission, and the exhaust temperature also affected the efficiency of Selected Catalytic Reduction(SCR) aftertreatment system, thus changing the NOx emission greatly.THC emission factors of LNG vehicles were 2.012–10.636 g/km, which were much higher than that of diesel vehicles(0.029–0.185 g/km).Unburned CH_4 may be an important reason for this phenomenon.Further on-road emission tests, especially CH_4 emission test should be carried out in subsequent research.In addition, the Particulate Number(PN) emission factors of diesel vehicles were at a very high level during whole tests, and Diesel Particulate Filter(DPF)should be installed to reduce PN emission.     

Dynamic nano-Ag colloids cytotoxicity to and accumulation by Escherichia coli: Effects of Fe3+, ionic strength and humic acid

Released Ag ions or/and Ag particles are believed to contribute to the cytotoxicity of Ag nanomaterials, and thus, the cytotoxicity and mechanism of Ag nanomaterials should be dynamic in water due to unfixed Ag particle:Ag⁺ ratios. Our recent research found that the cytotoxicity of PVP-Ag nanoparticles is attributable to Ag particles alone in 3 hr bioassays, and shifts to both Ag particles and released Ag⁺ in 48 hr bioassays. Herein, as a continued study, the cytotoxicity and accumulation of 50 and 100 nm Ag colloids in Escherichia coli were determined dynamically. The cytotoxicity and mechanisms of nano-Ag colloids are dynamic throughout exposure and are derived from both Ag ions and particles. Ag accumulation by E. coli is derived mainly from extracellular Ag particles during the initial 12 hr of exposure, and thereafter mainly from intracellular Ag ions. Fe³⁺ accelerates the oxidative dissolution of nano-Ag colloids, which results in decreasing amounts of Ag particles and particle-related toxicity. Na⁺ stabilizes nano-Ag colloids, thereby decreasing the bioavailability of Ag particles and particle-related toxicity. Humic acid (HA) binds Ag⁺ to form Ag⁺-HA, decreasing ion-related toxicity and binding to the E. coli surface, decreasing particle-related toxicity. HA in complex conditions showed a stronger relative contribution to toxicity and accumulation than Na⁺ or Fe³⁺. The results highlighted the cytotoxicity and mechanism of nano-Ag colloids are dynamic and affected by environmental factors, and therefore exposure duration and water chemistry should be seriously considered in environmental and health risk assessments.     

An investigation of changes in water quality throughout the drinking water production/distribution chain using toxicological and fluorescence analyses

Changes in water quality from source water to finished water and tap water at two conventional drinking water treatment plants(DWTPs) were monitored.Beside the routine water quality testing,Caenorhabditis elegans-based toxicity assays and the fluorescence excitation–emission matrices technique were also applied.Both DWTPs supplied drinking water that met government standards.Under current test conditions,both the investigated finished water and tap water samples exhibited stronger lethal,genotoxic and reprotoxic potential than the relative source water sample,and the tap water sample was more lethal but tended to be less genotoxic than the corresponding finished water sample.Meanwhile,the nearly complete removal of tryptophan-like substances and newly generated tyrosine-like substances were observed after the treatment of drinking water,and humic-like substances were identified in the tap water.Based on these findings,toxic pollutants,including genotoxic/reproductive toxicants,are produced in the drinking water treatment and/or distribution processes.Moreover,further studies are needed to clarify the potentially important roles of tyrosine-like and humic-like substances in mediating drinking water toxicity and to identify the potential sources of these contaminants.Additionally,tryptophan-like fluorescence may be adopted as a useful parameter to monitor the treatment performance of DWTPs.Our observations provided insights into the importance of utilizing biotoxicity assays and fluorescence spectroscopy as tools to complement the routine evaluation of drinking water.