喷灌和沟灌方式对农田土壤NH3挥发的影响

研究了2016和2017年传统灌溉（沟灌）和节水灌溉（喷灌）方式氨（NH₃）挥发的季节年际动态变化特征及其影响因素.采用通气法进行原位监测,分析了土壤温度、体积含水量、铵态氮（NH₄⁺-N）、硝态氮（NO₃^--N）以及气温降水等因素对NH₃挥发的影响.结果表明,NH₃挥发速率的峰值出现在施用氮肥后1~2周,喷灌有效降低NH₃挥发峰值,喷灌和沟灌的NH₃挥发速率峰值在2016年分别为2.67kg/（hm²·d）和11.11kg/（hm²·d）,2017年分别为2.42kg/（hm²·d）和11.73kg/（hm²·d）;马铃薯生长季NH₃挥发存在明显的季节变化,挥发高峰主要发生在7~8月,追肥期高于基肥期.2016~2017年农田土壤NH₃累积挥发量均表现为喷灌<沟灌,与沟灌相比,喷灌分别减少58.15%和43.55%.NH₃挥发速率与土壤温度呈显著正相关（P<0.05）,与体积含水量、NH₄⁺-N、NO₃^--N浓度呈极显著正相关（P<0.01）.     

内蒙古河套灌区盐碱土壤N2O排放特征

选择内蒙古河套灌区强度盐碱土壤S₁[电导率（EC）2.60dS/m]和轻度盐碱土壤S₂[电导率（EC） 0.74dS/m]为研究对象,2014~2016年,利用静态箱法3年野外原位观测试验,研究盐碱土壤氧化亚氮（N₂O）排放通量.结果表明：2种不同盐碱程度土壤N₂O排放每年均存在显著差异,轻度盐碱土壤N₂O累积排放量低;随EC升高,土壤盐碱程度加重,土壤N₂O累积排放量升高.2014~2016年作物生长季（4~11月）轻度盐碱土壤N₂O累积排放量分别为180.6,167.6,118.2mg/m²;强度盐碱土壤N₂O累积排放量比轻度盐碱土壤分别增加19%、26%和45%,修复盐碱土壤成为减缓盐碱土壤N₂O累积排放的重要农艺措施.     

UV和UV/H2O2工艺对水中二嗪磷的降解

在低压汞灯（LPUV,253.7nm）光照条件下,研究了过氧化氢（H₂O₂）加入量对二嗪磷降解动力学、产物生成和降解途径的影响规律与作用机理.结果表明,二嗪磷水溶液在单独UV和UV/H₂O₂工艺中的降解反应均符合准一级反应动力学,且反应速率常数（k）随H₂O₂加入量的增加而增大,H₂O₂加入量为0,5,10mg/L时的k分别为0.0234,0.0301,0.0341min-1.在UV光照处理条件下,二嗪磷水溶液中的溶解性有机碳（DOC）随H₂O₂加入量的增加而降低,但其矿化度均相对较低（光照120min时的DOC去除率均低于20%）.此外,UV光照处理时,H₂O₂的加入对二嗪磷光氧化降解产物的种类及生成量均存在显著影响.二嗪磷水溶液单独UV光照处理60min时检出了8种中间/降解产物,但经UV/H₂O₂工艺处理60min时仅检出了6种中间/降解产物,且不同H₂O₂加入量时的光氧化降解产物生成量或浓度及随UV光照处理时间的变化幅度与趋势均存在较大程度的差别.基于二嗪磷及其降解产物的定性、（半）定量分析结果,提出了二嗪磷水溶液在单独UV和UV/H₂O₂工艺中的降解途径与机理.     

Application of interface material and effects of oxygen gradient on the performance of single-chamber sediment microbial fuel cells (SSMFCs)

Single-chamber sediment microbial fuel cells(SSMFCs) have received considerable attention nowadays because of their unique dual-functionality of power generation and enhancement of wastewater treatment performance. Thus, scaling up or upgrading SSMFCs for enhanced and efficient performance is a highly crucial task. Therefore, in order to achieve this goal, an innovative physical technique of using interface layers with four different pore sizes embedded in the middle of SSMFCs was utilized in this study.Experimental results showed that the performance of SSMFCs employing an interface layer was improved regardless of the pore size of the interface material, compared to those without such layers. The use of an interface layer resulted in a positive and significant effect on the performance of SSMFCs because of the effective prevention of oxygen diffusion from the cathode to the anode. Nevertheless, when a smaller pore size interface was utilized, better power performance and COD degradation were observed. A maximum power density of 0.032 mW/m~2 and COD degradation of 47.3% were obtained in the case of an interface pore size of 0.28 μm. The findings in this study are of significance to promote the future practical application of SSMFCs in wastewater treatment plants.     

Highly catalytic activity of Mn/SBA-15 catalysts for toluene combustion improved by adjusting the morphology of supports

Rod-like, hexagonal and fiber-like SBA-15 mesoporous silicas were synthesized to support MnO_x for toluene oxidation. This study showed that the morphology of the supports greatly influenced the catalytic activity in toluene oxidation. MnO_x supported on rod-like SBA-15(R-SBA-15) displayed the best catalytic activity and the conversion at 230°C reached more than 90%, which was higher than the other two catalysts. MnO_x species consisted of coexisting MnO_2 and Mn_2O_3 on the three kinds of SBA-15 samples. Large amounts of Mn_2O_3 species were formed on the surface and high oxygen mobility was obtained on MnO_x supported on R-SBA-15, according to the H_2 temperature programmed reduction(H_2-TPR)and X-ray photoelectron spectroscopy(XPS) results. The Mn/R-SBA-15 catalyst with greater amounts of Mn_2O_3 species possessed a large amount of surface lattice oxygen, which accelerated the catalytic reaction rate. Therefore, the surface lattice oxygen and high oxygen mobility were critical factors on the catalytic activity of the Mn/R-SBA-15 catalyst.     

Effect of air masses motion on the rapid change of aerosols in marine atmosphere

The impact of air masses motion on marine aerosol properties was investigated using an on-board single particle mass spectrometer(SPAMS) deployed for the determination of single particle size resolved chemical composition over Southeast China Sea. Two aerosol blooms(E1 and E2) were observed during the cruise. High average particle number count occurred in E1(7320), followed by E2(5850), which was more than 100–150 times of the average particle number count during normal periods. Particles were classified as four major sources, including continental source, shipping source, marine source, and transport source based on the mass spectral similarity. Transport source was identified as those particles with high particle number count occurred only during aerosol bloom period. Three sub-types of EC-Ca, OC-Ca, and Al-rich were classified as transport source.EC-Ca was the dominant particles of the transport source, accounting for more than 70%of the total particles in aerosol bloom events. A uni-modal size distribution in the size range of 0.1–2.0 μm was observed during normal period, while a bimodal distribution with a tiny mode(0.3 μm) and a coarse mode between 0.4 and 0.6 μm was present during aerosol bloom. The variation of aerosol source is consistent with air masses back trajectories, for the reason that most of the long-range air trajectories are from the ocean,while short air trajectories originate in the continental regions, which means that air masses have a significant impact on the aerosol physical–chemical properties along their tracks.     

电弧离子镀HY11涂层的1200℃高温氧化行为研究

目的研究真空电弧镀方法制备的超高温金属涂层HY11在1200℃下的高温氧化行为。方法用真空电弧镀技术(AIP)在单晶镍基高温合金DD6上制备超高温金属涂层HY11,采用HB 5258循环氧化方法进行1200℃循环氧化试验,通过试验过程中试样质量变化评价涂层氧化寿命。通过扫描电镜(SEM)分析氧化后的试样显微形貌,用X-射线衍射仪分析涂层材料的相结构,通过氧化速率对涂层材料抗氧化性能进行表征。结果采用单靶真空电弧镀技术制备的HY11涂层,经过1050℃真空条件下扩散2h,涂层厚度为50～60?m,扩散区厚度为10～15μm,涂层微观组织均匀致密,涂层合金界面清晰平整。DD6合金的1200℃循环氧化寿命仅仅为4 h,HY11涂层在1200℃的循环氧化寿命近300 h。沉积态涂层HY11相结构主要以Al_2O_3和Ni3Al为主。氧化后涂层材料表面形成的氧化膜以Al_2O_3为主。结论 HY11涂层在1200℃的循环氧化寿命为298 h,极大地提高了DD6合金在1200℃的循环氧化寿命。     

我军"基地化宿营保障系统"建设初探

野营保障在后勤保障领域中地位特殊,是其他保障展开的基础和依托,如何适应现代战争体系作战的要求,实现体系化野营保障,是当今世界军事强国在后勤领域内的研究重点,针对此,通过研究美军"力量提供者系统"、俄军"自主式野战军营系统"和国内"救灾生活系统"等基地化宿营保障系统的研制目标、模块组成和使用情况,并从保障规模设置、功能模块组成、储运条件、保障力量设置与编程和主要运用场景及程序等方面,提出了我军基地化宿营保障系统建设的构想,旨在为提升我军野战条件下宿营保障的质量和效益进行探索。     

中石化广西液化天然气项目海洋自然灾害风险评估

中石化广西液化天然气（LNG）项目是广西沿海地区引进的国家重点清洁能源工程,其抵御海洋自然灾害的能力直接影响广西地区的经济发展速度。本研究结合LNG项目海岸防御工程的设计标准及现状,进行风暴潮、海浪自然灾害的设计标准及设计参数的风险分析,将推算得到的防御工程应达到的理论顶高程与实测高程进行对比,评估各段抵御海洋自然灾害的能力。研究发现无论是设计高潮位还是考虑海平面上升之后的极端高潮位均大于工程设计值;东南偏南（SSE）向波高的评估结果均大于设计值,其他方向波高的评估值与设计值差别不大;东南、西南段海岸防御工程的实测最低高程要低于评估高程,其他段具有一定的防御海洋自然灾害能力。     

贵州喀斯特山地农业系统不同种植区休耕地土壤水溶性氮素组成及分布特征

选择贵州喀斯特山地农业系统不同种植区休耕地土壤作为研究对象,对其水溶性氮素组成及分布特征进行了研究。结果表明:休耕地土壤SON含量范围为4. 11～14. 34 mg/kg,平均含量为8. 62 mg/kg。不同种植区休耕地土壤SON含量存在较大差异,但差异不显著(p0. 05),SON占TSN的比例差异极显著(p0. 01),传统农业种植区SON的变异较大,其它种植区的较小。水溶性氮素组成以SON和NH_4~+-N为主,不同种植区的NH_4~+-N、NO_3~--N占SIN的比例差异不显著(p0. 05),而两者占TSN及SIN占TSN的比例差异极显著(p0. 01)。传统农业种植区表层和深层土壤SIN的含量都要比其它种植区高,SON则相反,说明不同类型的农业对土壤氮的影响不同。不同种植区表层土NH_4~+-N、NO_3~--N、TSN、SON含量差异极显著(p0. 01)。除了打通种植区,其它种植区NH_4~+-N含量随着土层的增加总体上表现出下降的规律。除了大冲种植区在0～30 cm深度先增加后降低的规律外,其它种植区NO_3~--N含量自土壤表层到30 cm深度,随着土层的增加而增加,自30 cm深度往下,随着土层的增加而下降。TSN和SON中,除了青岩种植区随着土壤表层到20 cm深度处降低外,其它种植区随着土壤表层到20 cm深度处先增加,然后从20 cm深度往下随着土层的增加再降低。SON容易向下淋失,不易在土层深部发生积累,造成氮素的流失和带来环境污染风险,应引起重视。