Absorption of NO and NO2 in Caprolactam Tetrabutyl Ammonium Halide Ionic Liquids

ABSTRACT

To explore environmentally benign solvents for the absorption of NO and NO₂, a series of caprolactam tetrabutyl ammonium halide ionic liquids were synthesized. The solubility of NO and NO₂ was measured at temperatures ranging from 298.2 to 363.2 K and atmospheric pressure, and the following trend in the solubility of NO and NO₂ in ionic liquids with various halide anions was observed, respectively: F > Br > Cl and Br > Cl > F. Moreover, as the temperature increased from 308.15 to 363.15 K and the mole ratio of caprolactam increased from 2:1 to 6:1, the solubility of NO increased. Alternatively, the solubility of NO₂ decreased as the temperature increased from 298.15 to 363.15 K, and the mole ratio of caprolactam increased from 2:1 to 6:1. The absorption and desorption of NO and NO₂ was practically reversible in the ionic liquids, which was characterized by nuclear magnetic resonance. The method, which is at least partially reversible, offers interesting possibilities for the removal of NO and NO₂.

IMPLICATIONS Basic ionic liquids with amino groups were synthesized and used to capture CO₂, SO₂, and H₂S, and to promote hydrogenation of CO₂. In this paper, the authors used caprolactam tetrabutyl ammonium halide ionic liquid (IL) as absorbing medium in which NO_x could be absorbed. NO_x desorbed from the absorbent could be efficiently reduced by right catalysts at high temperature. The absorbed NO and NO₂ gas could be desorbed at higher temperature, allowing the ionic liquids to be reused several times without loss of capability. It was believed that caprolactam tetrabutyl ammonium bromide (CPL-TBAB) ILs may be useful for NO_x removal reagent for pollution control.     

聚丙烯中空纤维膜生物反应器净化复合芳香族VOCs

采用中空纤维膜生物反应器(HFMBR)去除气态复合苯系物。挂膜后期,生物反应器的去除效率可以稳定达到80%左右(去除能力(EC)≥225 g/(m3.h))。研究了中空纤维膜生物反应器处理对于单一二甲苯以及混合二甲苯的性能,并且发现HFMBR对于去除单一二甲苯和混合二甲苯都有明显的效果,去除效率均达到90%以上;表明二甲苯之间竞争效应带来的相互抑制作用小。在低浓度的情况下,单一二甲苯和混合二甲苯的去除能力呈线性增加,在高浓度阶段,去除能力增加变缓。比较了混合二甲苯与甲苯联合降解,发现两者之间存在相互抑制作用,但相比传统生物反应器有明显的改善。与传统生物过滤系统比较而言,膜生物反应器有着很好的应用前景。     

炼油废水微生物燃料电池启动及影响因素

以炼油废水为碳源,构建双室填料型微生物燃料电池,考察接种液、外接电阻等电池启动条件,以及电导率、pH值和缓冲溶液强度等溶液性质对电池产电性能的影响。利用微生物燃料处理炼油废水,COD去除率(52±4)%,含油量去除率(81.8±3)%;利用废水中存在的原生菌即可启动电池,但启动期长,外加接种液可快速启动电池;启动时外接电阻的大小对电池稳定运行后的输出功率有明显影响,对电池内阻影响相对较小,当启动外接电阻为2 000Ω,电池输出功率最大,为288 mW/m3;随阳极溶液电导率电池增大,电池内阻降低,输出功率升高;pH值变化对电池阳极电势影响较大,进而影响电池输出,当溶液pH为9时,电池输出电压最大(388 mV),pH过高或过低均不利于电池产电;随着缓冲强度的增大,电池输出电压增大,且PBS缓冲强度的增大可从电导率增大和改善质子传递条件两方面提高电池的输出功率。     

布袋过滤除尘中气固两相流的格子Boltzmann模拟

使用格子Boltzmann方法对含尘气体通过布袋滤料纤维的流动进行了数值模拟,采用拉格朗日方法跟踪了颗粒相中每个粒子的位置和速度并进行单向耦合计算。分析了气流通过纤维捕集体过程中的压降的变化规律,结果与达西渗透定律吻合。与此同时,对粒径小于1μm的气溶胶粒子在布袋纤维捕集体上的沉积规律展开了讨论。结果表明,粒径小于0.01μm的粒子的捕集主要受粒子的布朗随机扩散效应的控制;粒径大于0.1μm的粒子则主要依靠纤维滤料的拦截作用而沉积在捕集体表面;而粒径在0.01～0.1μm范围的粒子则具有较低的捕集效率。模拟结果为研究袋式除尘的过滤机理提供了依据。     

全细胞脂肪酶(菌)对SBR系统中活性污泥性能的影响

将全细胞脂肪酶(菌)以产脂肪酶微生物的形式直接投加到SBR内,与投加野生型酵母菌及空白对照进行比较,研究其对活性污泥性能及含油脂废水处理效果的影响。结果表明,在15～20℃,pH 6.5～7.5,进水油脂浓度2 000 mg/L的条件下,投加一定量全细胞脂肪酶(菌)的SBR系统间歇处理4 d,活性污泥增殖速度加快,是投加野生型酵母菌的1.3倍。静置30 min时活性污泥SV达到45%,SVI为151,MLSS最高可达2 965 mg/L左右,絮凝时间缩短且无污泥膨胀现象。投加全细胞脂肪酶(菌)的SBR系统中,油脂去除率为86.5%,COD去除率为79.5%,与投加野生型酵母菌的SBR系统相比去除率提高了1.3倍。说明投加全细胞脂肪酶(菌)后活性污泥性能增强,油脂废水处理效率提高。     

微波诱导鳞片石墨-H2O2催化氧化处理甲基紫废水

研究微波诱导鳞片石墨-H₂O ₂催化氧化处理甲基紫废水工艺,探讨各种因素的协同作用及对废水脱色效果的影响,并采用SEM、EDX、XRD和FTIR对新鲜及使用6次后的鳞片石墨进行表征。结果表明,微波诱导鳞片石墨-H₂O₂能高效快速降解废水中的甲基紫;在50 mL初始pH为3,质量浓度为10 mg/L的甲基紫废水中, H₂O₂用量1 mL/L,鳞片石墨 3 g/L,微波输出功率259 W,微波辐射时间9 min的最佳处理工艺条件下,甲基紫脱色率达到了98.80%;微波、鳞片石墨、H₂O₂体系对甲基紫废水降解效果明显,产生协同效应。紫外-可见光谱分析表明,废水中甲基紫结构被破坏,但仍含有少量苯环等小分子。动力学研究表明,脱色反应符合一级反应动力学规律,反应速率常数k为0.42613 min^-1,反应半衰期t_1/2为1.626 min。     

温度对活性污泥-生物膜复合工艺中红斑体虫爆发性繁殖影响

活性污泥-生物膜复合工艺在春夏之交常发生红斑顠体虫的爆发性繁殖,使系统性能恶化。用烧杯实验模拟活性污泥-生物膜复合工艺,保持填料投配率为30%,分别在不同温度下（20,25,30℃）运行实验装置,待运行稳定后,接种红斑顠体虫,创造条件以观察红斑顠体虫是否发生爆发性繁殖。实验结果发现,红斑顠体虫在25℃和30℃都不同程度产生了爆发性繁殖,最大种群密度分别达到383个/mL和200个/mL,同时,红斑顠体虫的爆发性繁殖不会对进出水的COD和氨氮去除产生影响;在温度25℃和30℃时,红斑顠体虫爆发性繁殖都导致了总氮的释放,红斑顠体虫种群密度分别大于等于66个/mL和50个/mL可分别作为红斑顠体虫在25℃和30℃发生爆发性繁殖的标志;实验也证明了红斑顠体虫的爆发性繁殖不会产生大量啃食生物膜的现象;用SPSS做多元线性回归分析,得出红斑顠体虫的最大种群密度与总氮的释放显著相关。     

Mechanical Properties of Poly (Lactic Acid)/Hemp Fiber Composites Prepared with a Novel Method

This research dealt with a novel method of fabricating green composites with biodegradable poly (lactic acid) (PLA) and natural hemp fiber. The new preparation method was that hemp fibers were firstly blending-spun with a small amount of PLA fibers to form compound fiber pellets, and then the traditional twin-screw extruding and injection-molding method were applied for preparing the composites containing 10–40 wt% hemp fibers with PLA pellets and compound fiber pellets. This method was very effective to control the feeding and dispersing of fibers uniformly in the matrix thus much powerful for improving the mechanical properties. The tensile strength and modulus were improved by 39 and 92 %, respectively without a significant decrease in elongation at break, and the corresponding flexural strength and modulus of composites were also improved by 62 and 90 %, respectively, when the hemp fiber content was 40 wt%. The impact strength of composite with 20 wt% hemp fiber was improved nearly 68 % compared with the neat PLA. The application of the silane coupling agent promoted further the mechanical properties of composites attributed to the improvement of interaction between fiber and resin matrix.     

阳离子表面活性剂改性四氧化三铁-沸石复合材料对水中刚果红的去除作用

制备了四氧化三铁-沸石复合材料(磁性沸石)和阳离子表面活性剂改性磁性沸石(有机改性磁性沸石),采用X射线衍射分析对有机改性磁性沸石进行了表征,通过批量实验考察了有机改性磁性沸石对水中刚果红的吸附性能,并对相关的吸附机制进行了讨论。实验表明,有机改性磁性沸石对水中的刚果红具备良好的吸附能力,且有机改性磁性沸石对刚果红的吸附能力远远高于磁性沸石。有机改性磁性沸石对水中刚果红的吸附动力学符合准二级动力学模型,吸附平衡数据可以采用Langmuir、Freundlich和Dubinin-Radushkevich(D-R)等温吸附模型加以描述。根据Langmuir等温吸附模型计算得到的有机改性磁性沸石对刚果红的最大吸附容量为146 mg/g(pH 7和30℃)。有机改性磁性沸石对水中刚果红的吸附属于自发和放热的过程。有机改性磁性沸石吸附水中刚果红的作用机制包括静电吸引、有机相分配、氢键和表面配位。X射线衍射分析结果表明,有机改性磁性沸石含四氧化三铁,吸附刚果红后的有机改性磁性沸石可以很容易地通过外加磁场的作用快速地从水中分离出来。上述结果表明,有机改性磁性沸石适合作为一种吸附剂去除废水中的刚果红。     

北京大学非采暖期室内空气中的气态多环芳烃

同步采集并分析了非取暖期北京大学住宅小区和教学楼室内和室外大气样品中气态PAHs含量.结果表明,室内空气中气态PAHs含量高于室外.室内外样品相似的化合物分布谱说明室内污染主要来自室外空气.距交通干线近的样点室内外浓度均高于对照样点,说明非取暖期机动车排放是城市室内外空气中气态PAHs的主要来源.挥发性弱的高环化合物含量表现出比低环易挥发化合物更明显的随距交通干线距离变化的趋势.此外,所有室内空气中气态PAHs含量均高于对应的室外样品.