Emission characterization of unintentionally produced persistent organic pollutants from iron ore sintering process in China

Emission of unintentionally produced persistent organic pollutants (Unintentional POPs), including polychlorinated dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs), polychorinated biphenyls (PCBs), hexachlorobenzene (HxCBz) and pentachlorobenzene (PeCBz), were investigated in four typical iron ore sintering plants in China. The emission factors and annual mass releases of the Unintentional POPs were calculated. The results indicated that PCDFs contributed more than 60% to the overall toxic equivalent quantity (TEQ) values, while the contribution of the dl-PCBs is relatively low, and only in the range of 8-9%. The dominant congeners of PCDD/Fs and dl-PCBs contributing most to the total TEQ were 1,2,3,7,8-PeCDD, 2,3,4,7,8-PeCDF and PCB-126. With regard to the TEQ contributions, the most abundant homologues were PeCDFs and HxCDD/Fs, followed by PeCDDs and non-ortho dl-PCB, whereas HpCDD/Fs, OCDD/Fs and mono-ortho dl-PCBs almost made no contributions. Due to the massive use of recycled waste in the feeding materials, the average emission factor of PCDD/Fs and dl-PCBs of the four plants was 3.95 μg WHO-TEQ ton⁻¹. Based on the results, the annual release of PCDD/Fs and dl-PCBs in 2007-2009 were estimated to be 2070 g, 2212 g, and 2307 g WHO-TEQ, respectively.     

无砾石微孔管地下渗滤系统处理生活污水的中试研究

进行了无砾石微孔管地下渗滤系统处理生活污水的中试研究。基于不同土壤、不同管径、不同植物的协同效应,对比研究了不同系统处理污水中有机物、氮、磷和SS的去除效果及其影响因素。结果表明,不同土壤、不同管径及不同植物组成的系统,对生活污水中有机物、氮、磷和SS的去除效果差别较大。中试系统对COD、总磷、氨氮、总氮和SS的最佳去除率分别达到86.13%、90.20%、61.24%、65.49%和97.43%,对应的出水COD、总磷、氨氮、总氮和SS的平均浓度分别为64.29、0.69、22.13、26.19和5.56 mg/L。分析表明,进水SS浓度过高、外界温度下降等共同作用是导致系统对生活污水中NH4+-N和TN的去除率相对较低的主要原因。     

高分子量高纯度阳离子聚丙烯酰胺的合成

以丙烯酰胺与丙烯酰氧乙基三甲基氯化铵为单体,在复合引发剂的作用下,选择水溶液共聚法合成高分子量与高纯度阳离子型聚丙烯酰胺(CPAM)。实验表明,有机偶氮引发剂A用量0.5‰、氧化还原引发剂用量0.45‰、还原剂与氧化剂摩尔比2∶1、反应体系pH为4与反应时间5 h条件下,CPAM分子量为1 042万,且溶解性好。通过对聚合物残单含量影响因素添加剂用量、反应时间的研究,结果表明,添加剂EDTA和增溶剂D对残留AM含量影响小,而苯甲酸钠对聚合物残留AM的含量影响显著;延长反应时间至7 h,残单含量可降低至0.27%,CPAM的纯度高。通过与国内外3种同类型产品进行对比,结果表明,自制产品的分子量明显高于其他产品,且残单含量比国内产品降低了50%～75%。     

强化混凝工艺深度处理给水厂排泥废水

水厂废水的综合处理与回用是我国供水行业的新趋势和节水目标所在,采用强化混凝技术进行水厂排泥废水的深度处理。通过混凝剂筛选实验和有机物表征确定最佳混凝剂为高效聚合铝(HPAC),适宜投加量为650 mg/L。当混凝剂HPAC投加量为650 mg/L时,对COD、TOC、浊度和色度的去除率分别为82.5%、89.8%、95%和92.5%,相应的出水值分别为58 mg/L、8.46 mg/L、2.35 NTU、13度,COD满足《污水综合排放标准》(GB 8978-1996)的要求(COD≤100 mg/L),同时实验结果显示聚合氯化铝(PAC)、HPAC、三氯化铁(FeCl3)主要去除分子量处于>1 300 Da范围的有机物,对分子量处于744～1 300 Da之间的有机物去除有限。     

晚期垃圾渗滤液的部分亚硝化

利用实验室小试SBR在(33±1)℃的条件下,通过动态调控溶氧浓度(DO)(2～7 mg/L)和水力停留时间(2～5 d),经过130 d的运行成功启动了晚期垃圾渗滤液(NH4+-N含量1 227～2 133 mg/L)的部分亚硝化,使出水NO2--N∶NH4+-N稳定维持在1∶1左右,为后续的厌氧氨氧化工艺创造了进水条件。利用实时荧光定量PCR研究启动过程中的特异微生物氨氧化细菌的含量变化表明,氨氧化细菌的含量与NO2--N的生成速率和出水NO2--N稳定性有着显著相关性。     

核桃壳粉对水溶液中Pb2＋的吸附

实验通过间歇吸附方式研究了核桃壳粉对水溶液中Pb^2＋的吸附特性,探讨了核桃壳粉粒径及用量、溶液pH、Pb^2＋初始浓度等参数对吸附的影响,并讨论了吸附过程的热力学和动力学特征。结果表明,核桃壳粉对Pb^2＋吸附的最佳pH为5．0,去除率随吸附剂粒径的减小、用量的增加、Pb^2＋初始浓度的减小而增加。优化实验条件下,0～0．3mm15g／L的吸附剂在298K时,对pH=5的50mL50mg／LPb^2＋溶液的去除率达96．98％。核桃壳粉对Pb^2＋的吸附等温线符合Sips模型,在283、293和303K的最大吸附量分别为18．25、18．27和20．94mg／g。吸附过程是放热的、混乱度减小的自发过程,且符合准二级动力学模型。吸附速率常数随温度升高而减小,在293和303K时分别在90和120min基本达到平衡。结合FTIR和SEM手段发现核桃壳对Pb^2＋的吸附以物理吸附为主,同时包括离子交换、螯合等化学吸附以及颗粒内扩散步骤,是一个复杂的过程。     

一种新型Fenton-流化床催化剂的制备及表征

非均相Fenton-流化床体系主要使用石英砂作为催化剂载体,该技术的实际应用由于催化剂活性寿命低、制备困难等原因而受到限制.提出了一种新型的Fenton-流化床催化剂——负载氧化铁陶粒.使用循环浸泡法制备的负载陶粒对苯甲酸模拟废水的处理效果良好.表征结果分析表明,载体表面铁含量大幅度上升,负载的氧化铁紧紧包裹在陶粒表面,且表面有大量缝隙,利于增加反应比表面积,而密度变化不大.该催化剂的催化活性重复性良好,重复使用4次后对苯甲酸模拟废水依然有较好的处理效果.使用该催化剂进行垃圾渗滤液的降解实验能在一定程度上减少亚铁的投加量,具有较好的实际应用前景.     

以焦炭为填料的生物滴滤塔处理含挥发性脂肪酸臭气

在以焦炭为填料的生物滴滤塔对挥发性脂肪酸臭气的处理研究中考察了空床停留时间、臭气浓度、体积负荷以及进气温度等参数对净化效果的影响。结果表明,空床停留时间较长时对臭气降解有利。在停留时间超过97 s时,能实现完全降解;此外,净化率随臭气浓度和体积负荷的不断增加呈先增加后降低的趋势。当臭气浓度为24.29 mg/m³即臭气的体积负荷为3 g/（m³·h）时,去除率约为96%;当臭气浓度增至1 345.74 mg/m³即体积负荷增至18 g/（m³·h）,去除率达100%;然而,当臭气浓度增至4 934.38 mg/m³即体积负荷增至66 g/（m³·h）时,去除率降至73.1%。另外,进气温度对净化率也有一定程度影响。当进气温度较低时,净化效率相对较高。     

钢渣掺量对泡沫混凝土砌块性能的影响

泡沫混凝土是一种环保、节能的保温隔热材料,以其优良的保温性能,受到越来越多研究者的关注。对钢渣的特性进行了分析测试,对钢渣不同掺量对泡沫混凝土砌块特性的影响进行了研究,结果表明,采用添加5％～35％钢渣所制备的钢渣泡沫混凝土砌块,其密度等级为JC／T1062—2007中的B10级,掺人5％、15％钢渣的泡沫混凝土抗压强度达到A3．5等级,掺人25％、35％钢渣的泡沫混凝土抗压强度达到A2．5等级。随着钢渣掺量的增大,抗压强度、抗折强度降低,吸水率增大。在同一钢渣掺量的情况下,泡沫混凝土砌块的抗压强度变化率增加显著,而且随着钢渣的加入量升高而增大。钢渣的加入有利于提高泡沫混凝土砌块的后期抗压强度。     

Thermogravimetric analysis and kinetic study on pyrolysis of representative medical waste composition

To obtain detailed information on the pyrolysis characteristics, a thermogravimetric study on the pyrolysis of 14 typical medical waste compositions was carried out in thermogravimetric analysis (TGA) equipment using dynamic techniques in a stream of N(2). An index representing pyrolysis reactivity of waste was presented. Kinetic parameters were obtained by Coats-Redfern method and used to model the TG curve. The results showed that: (a) Plastic, protein, cellulosic material, synthetic fibre, and rubber entered pyrolysis process in succession. (b) There was one decomposition stage in the pyrolysis of one-off medical glove, operating glove, cellulosic waste, absorbable catgut suture and adhesive plaster, while other components had two obvious weight loss stages. (c) The obtained apparent activation energy for second stage pyrolysis was comparably higher than that for first stage. (d) Each stage was controlled by only one kinetic mechanism, in which kinetic parameters were constant. (e) The degradation kinetics of medical waste may be affected by special physical and chemical treatment in the product manufacturing process. (f) Among 13 waste samples, the pyrolysis index of cellulosic matter was the highest, which indicated cellulosic matter had strong pyrolysis reactivity. (g) With increasing heating rate, TG curve and DTG peak shifted to high temperatures and main reaction interval of the sample became longer.