铜绿假单胞菌对铜和铅的吸附

研究了铜绿假单胞菌(Pseudomonas aeruginosa)对Cu和Pb的吸附特性.结果表明,相同条件下,该菌株对Cu~(2+)的吸附率低于Pb~(2+).对于单一重金属体系,吸附率均随时间的延长先上升后平稳变化,2 h达到稳定.吸附率随投菌量的增加先迅速增加,之后趋于平稳.对于Cu~(2+),投菌量为1 g·L~(-1)时吸附率达到稳定,而Pb~(2+)的吸附效果达到平稳时的投菌量为0.5 g·L~(-1).单位质量菌体对Cu~(2+)、Pb~(2+)的吸附量随投菌量的增加而下降.pH为3时,菌体的吸附效果较差,当pH为5~8时,2种重金属的吸附效果较高.对于活菌,Pb~(2+)对菌体吸附Cu~(2+)有抑制作用,而Cu~(2+)对菌体吸附Pb~(2+)的影响无明显规律.对于失活菌,P.aeruginosa吸附Pb~(2+)和Cu~(2+)的效果均随共存重金属浓度的增大而降低,但Cu~(2+)对Pb~(2+)的影响比Pb~(2+)对Cu~(2+)的影响更显著.扫描电镜观察发现,吸附后的菌体较吸附前聚集性更好.总体而言,P.aeruginosa能对水体中共存的Cu~(2+)和Pb~(2+)有较好的吸附效果.     

7种拟除虫菊酯农药对卤虫的急性毒性研究

为了研究7种拟除虫菊酯农药对美国大盐湖卤虫(GSL Artemia)的急性毒性效应,挑选18~24 h内孵出的卤虫,继续培养24 h后得到Ⅱ~Ⅲ龄卤虫无节幼体,将其暴露于所设浓度梯度的拟除虫菊酯溶液中进行24 h急性毒性实验,记录卤虫无节幼体在各浓度溶液中的死亡情况,并将所得数据进行Probit分析。结果表明,卤虫对不同拟除虫菊酯的敏感性相差较大。氯菊酯、氯烯炔菊酯、炔咪菊酯、胺菊酯、联苯菊酯、高效氯氟氰菊酯和溴氰菊酯对卤虫的24 h半致死浓度(24 h-LC50)分别为4.68、14.82、18.12、38.21、>100、>100和>100 mg.L-1。因此,在含有卤虫的盐水环境中,应尽量避免使用毒性较高的氯菊酯,而选择使用联苯菊酯、高效氯氟氰菊酯和溴氰菊酯等毒性较低的农药。     

单环硝基芳香化合物好氧生物降解及其遗传学研究进展

硝基芳香化合物是环境中难降解的有机污染物之一 ,对环境的污染日益严重 ,利用生物技术对这类有机物进行降解是行之有效的新途径。针对几种单环硝基芳香化合物好氧降解的微生物、降解途径以及降解过程中的主要酶、降解性质粒、基因定位等分子遗传学的研究进展进行了综述     

H2O2处理酸性大红GR染料废水的研究

通过对废水pH值、H2O2用量、催化剂用量、反应时间、反应温度等工艺条件的考察,确定了H2O2催化氧化处理酸性大红染料废水的最佳工艺条件pH 4、H2O2用量6 mL/L、催化剂用量3 g/L、反应时间100 min、反应温度70℃.在该条件下,COD和色度的去除率分别为76.7%和99.4%;通过反应前后的紫外-可见光光谱分析表明,H2O2催化氧化处理酸性大红GR染料废水有比较好的效果,为该工艺处理酸性大红GR染料废水提供了科学依据.     

An integrated method for the rapid dewatering and solidification/stabilization of dredged contaminated sediment with a high water content

• An integrated method, called PHDVPSS, was proposed for treating DCS. • The PHDVPSS method showed superior performance compared to conventional method. • Using the method, water content (%) of DCS decreased from 300 to<150 in 3 days. • The 56-day UCS from this method is 12‒17 times higher than conventional method. • Relative to PC, GGBS-MgO binder yielded greater reduction in the leachability. To more efficiently treat the dredged contaminated sediment (DCS) with a high water content, this study proposes an integrated method (called PHDVPSS) that uses the solidifying/stabilizing (S/S) agents and prefabricated horizontal drain (PHD) assisted by vacuum pressure (VP). Using this method, dewatering and solidification/stabilization can be carried out simultaneously such that the treatment time can be significantly shortened and the treatment efficacy can be significantly improved. A series of model tests was conducted to investigate the effectiveness of the proposed method. Experimental results indicated that the proposed PHDVPSS method showed superior performance compared to the conventional S/S method that uses Portland cement (PC) directly without prior dewatering. The 56-day unconfined compressive strength of DCS treated by the proposed method with GGBS-MgO as the binder is 12‒17 times higher than that by the conventional S/S method. DCS treated by the PHDVPSS method exhibited continuous decrease in leaching concentration of Zn with increasing curing age. The reduction of Zn leachability is more obvious when using GGBS-MgO as the binder than when using PC, because GGBS-MgO increased the residual fraction and decreased the acid soluble fraction of Zn. The microstructure analysis reveals the formation of hydrotalcite in GGBS-MgO binder, which resulted in higher mechanical strength and higher Zn stabilization efficiency.     

The size distribution of airborne bacteria and human pathogenic bacteria in a commercial composting plant

•Bacterial concentrations from eight stages were 10⁴–10⁵copies/m³. •Diameter influenced clustering of bacterial and HPB lineages. •Dg of 8 HPB ranged from 2.42 to 5.09 μm in composting areas. •Dg of 8 HPB ranged from 3.70 to 8.96 μm in packaging areas. •HPB had high concentrations and small sizes in composting areas. Composting plants are regarded as one of the important sources of environmental bioaerosols. However, limitations in the size distribution of airborne bacteria have prevented our comprehensive understanding of their risk to human health and their dispersal behavior. In this study, different sizes of airborne bacteria were collected using an eight-stage impactor from a full-scale composting facility. Size-related abundance and communities of airborne bacteria as well as human pathogenic bacteria (HPB) were investigated using 16S rRNA gene sequencing coupled with droplet digital PCR. Our results indicate that the bacterial concentrations from the eight stages were approximately 10⁴–10⁵copies/m³. Although no statistical correlation was detected between the particle size and the Shannon index, the influence of size on bacterial lineages was observed in both composting and packaging areas. For airborne bacteria from different stages, the dominant phyla were Firmicutes, Proteobacteria, and Actinobacteria, and the dominant genera was Bacillus. Seven out of eight HPB with a small geometric mean aerodynamic diameter had a high concentration in composting areas. Based on diameters of 2.42 to 5.09 μm, most HPB in the composting areas were expected to be deposited on the bronchus and secondary bronchus. However, in the packaging areas, the deposition of HPB (diameters 3.70 to 8.96 μm) occurred in the upper part of the respiratory tract. Our results on the size distribution, abundance, and diversity of these bacteria offer important information for the systematic evaluation of bacterial pathogenicity and the potential health impacts on workers in composting plants and the surrounding residents.     

Cu/Cr co-stabilization mechanisms in a simulated Al2O3-Fe2O3-Cr2O3-CuO waste system

• Cu and Cr can be mostly incorporated into CuFe_xAl_yCr_2−x−yO₄ with a spinel structure. • Spinel phase is the most crucial structure for Cu and Cr co-stabilization. • Compared to Al, Fe and Cr are easier to be incorporated into the spinel structure. • ‘Waste-to-resource’ by thermal process at attainable temperatures can be achieved. Chromium slag usually contains various heavy metals, making its safe treatment difficult. Glass-ceramic sintering has been applied to resolve this issue and emerged as an effective method for metal immobilization by incorporating heavy metals into stable crystal structures. Currently, there is limited knowledge about the reaction pathways adopted by multiple heavy metals and the co-stabilization functions of the crystal structure. To study the Cu/Cr co-stabilization mechanisms during thermal treatment, a simulated system was prepared using a mixture with a molar ratio of Al₂O₃:Fe₂O₃:Cr₂O₃:CuO= 1:1:1:3. The samples were sintered at temperatures 600–1300°C followed by intensive analysis of phase constitutions and microstructure development. A spinel phase (CuFe_xAl_yCr_2−x−yO₄) started to generate at 700°C and the incorporation of Cu/Cr into the spinel largely complete at 900°C, although the spinel peak intensity continued increasing slightly at temperatures above 900°C. Fe₂O₃/Cr₂O₃ was more easily incorporated into the spinel at lower temperatures, while more Al₂O₃ was gradually incorporated into the spinel at higher temperatures. Additionally, sintered sample microstructures became more condensed and smoother with increased sintering temperature. Cu / Cr leachability substantially decreased after Cu/Cr incorporation into the spinel phase at elevated temperatures. At 600°C, the leached ratios for Cu and Cr were 6.28% and 0.65%, respectively. When sintering temperature was increased to 1300°C, the leached ratios for all metal components in the system were below 0.2%. This study proposes a sustainable method for managing Cu/Cr co-exist slag at reasonable temperatures.     

Numerical study of wave–current–vegetation interaction in coastal waters

Research on interactions among wave, current, and vegetation has received increasing attention. An explicit depth-averaged hydrodynamic model coupled with a wave spectral model (CMS-wave) was proposed in this study in order to simulate the wave and wave-induced current in coastal waters. The hydrodynamic model was based on the finite volume method while the intercell flux was computed by employing the Harten–Lax–van Leer approximate Riemann solver to investigate the dry-to-wet interface, and the drag force of vegetation was modeled as the sink terms in the momentum equations. The CMS-wave model was used to investigate the non-breaking and the breaking random waves propagation in vegetation fields. Afterwards, an empirical wave energy dissipation term with plant effect was derived to represent the resistance induced by aquatic vegetation in the wave-action balance equation. The established model was calibrated and validated with both the experimental and field data. The results showed that the wave height decreased significantly along the wave propagation direction in the presence of vegetations. The sensitivity analysis for the plant density, the wave height, and the water depth were performed by comparing the numerical results for the wave height attenuation. In addition, wave and wave-induced current through a finite patch of vegetation in the surf zone were investigated as well. The strong radiation stress gradient could be produced due to the variation of the energy dissipation by vegetation effect in the nearshore zone, which impacted the direction and amplitude of the longshore current. The calculated results showed that the coupling model had good performance in predicting wave propagation and the current over vegetated water regions.     

Effect of effluent organic matter on ozonation of bezafibrate

The influence of three effluent organic matter (EfOM) model compounds, humic acid (HA), bovine serum albumin (BSA), and sodium alginate (AGS), on the ozonation of bezafibrate (BF), a typical pharmaceutical and personal care product (PPCP), was investigated. The results show that ozonation efficiently removed BF from aqueous solution with removal efficiencies>95% within 8 min for all conditions. The reaction rate of BF decreased with increasing model compounds concentrations and the influence was more pronounced for HA and BSA, while less pronounced for AGS. Although BF concentration was significantly reduced, the degree of mineralization achieved was only approximately 11%. The addition of HA and BSA improved the mineralization of the solution, while the influence of AGS was minor. The acute toxicity of BF solution during ozonation was determined using the Luminescent bacteria test, and the toxicity exhibited an initial increase and a successive reduction. An overall decreased acute toxicity was observed with an increase of HA. The presence of BSA increased the formation rate of toxicity intermediates and resulted in inhibition peak forward.     

异噻唑啉酮类杀菌剂对黑斑蛙胚胎和蝌蚪的急性毒性

异噻唑啉酮类杀菌剂1,2-苯并异噻唑-3-酮（BIT）和甲基异噻唑啉酮（MIT）虽已在多种行业中广泛使用,但目前有关其毒性尤其对水体中生物毒性的数据还较少。鉴于BIT和 MIT在水体中普遍存在,本文研究了这两种污染物对两栖动物黑斑蛙胚胎和蝌蚪的急性毒性。黑斑蛙胚胎和蝌蚪分别暴露系列浓度的BIT和 MIT,观察化学品对其生长、发育和运动的影响,计算96小时半数致死浓度（96 h-LC₅₀）和96小时半数致畸浓度（96 h-TC₅₀）,确定最小生长抑制浓度（MCIG）。结果发现,BIT对黑斑蛙胚胎的96 h-LC₅₀和96 h-TC₅₀分别为2.99 mg?L^-1和0.60 mg?L^-1,MCIG小于0.40 mg?L^-1,对蝌蚪的96 h-LC₅₀为6.44 mg?L^-1。MIT对黑斑蛙胚胎的96 h-LC₅₀和96 h-TC₅₀分别为5.30 mg?L^-1和2.36 mg?L^-1,MCIG为2.59 mg?L^-1,对蝌蚪的96 h-LC₅₀为7.58 mg?L^-1。根据《化学农药环境安全评价准则报批稿》中两栖动物蝌蚪急性毒性的分级标准,判定BIT和MIT的毒性等级为中等。该毒性数据为异噻唑啉酮类杀菌剂的环境管理提供参考。