MCM-41介孔分子筛的合成及其对铜离子的吸附性能简

以微硅粉为硅源,CTAB和PEG-6000为模板剂,合成MCM-41介孔分子筛。采用XRD、N₂吸附-脱附曲线、FTIR以及TEM表征了其结构、比表面积、孔径分布及晶体形貌,并且以该样品为吸附剂,对含Cu²⁺的溶液进行了静态吸附实验。结果表明,以微硅粉为硅源成功合成了具有典型六方排列孔道结构的MCM-41,其比表面积为869.5 m²/g,孔容为0.97 cm³/g,平均孔径为3.3 nm;溶液pH为5~6时,MCM-41对Cu²⁺的去除效果最好;MCM-41对Cu²⁺的最大吸附吸附容量36.3 mg/g;MCM-41对Cu²⁺的吸附性能符合Langmuir吸附方程的特征。动力学研究表明,该过程符合准二级动力学模型。     

水泥窑共处置过程中水泥生料对砷的吸附/冷凝特性

针对水泥生料开展了氮吸附与SEM测试分析,研究了水泥生料的比表面积,孔径结构和微观表面积。同时,利用管式回转炉和控温立式炉联用装置研究了砷元素在水泥生料上的吸附冷凝特性。结果表明,水泥生料的比表面积很小,微观表面结构致密无孔,砷元素主要是冷凝在生料表面上。进入吸附冷凝炉的重金属可以分为3部分,第1部分冷凝在管壁上,占80%左右;第2部分吸附/冷凝在生料上,占10%左右;第3部分随烟气释放到空气中,不到10%。水泥生料对砷的吸附冷凝量随时间的增加而增加,随温度的升高而降低。水泥生料对砷的吸附冷凝特性可用双常数速率方程拟合,拟合效果较好,计算得表观活化能在6~7 kJ/mol之间。此外,砷的初始浓度对水泥生料的吸附冷凝特性影响很小。     

改性壳聚糖复合凹凸棒土絮凝油漆废水

将壳聚糖、阳离子淀粉和二甲基二烯丙基氯化铵(DMDAAC)进行三元接枝共聚,制备了三元接枝改性壳聚糖(CTS-DMDAAC-CS),通过红外光谱和扫描电镜对其结构进行了表征。并且将三元接枝改性壳聚糖与凹凸棒土进行优化复配,对油漆废水进行了絮凝实验,得出了当pH=12,沉降时间为20 min,复合絮凝剂投加量为0.2 g,三元接枝共聚物∶凹凸棒土=1∶10时,该复合絮凝剂对油漆去除率最佳能够达到89.3%,并且絮凝效果好,是一种新型绿色环保的有机-无机复合絮凝剂。     

CdIn2S4/复合材料的制备及光降解罗丹明B

利用高压静电纺丝技术,制得含有羧基的导电聚合物纤维(聚偏氟乙烯/苯乙烯-马来酸酐共聚物/纳米石墨),高温水热条件下在纤维表面制备CdIn2S4颗粒,得到CdIn2S4/导电聚合物纤维复合材料。运用扫描电子显微镜(SEM)、X射线衍射仪(XRD)、紫外-可见吸收光谱仪(UV-Vis)和热失重分析仪(TGA)对复合材料的结构进行表征。并利用350 W氙灯模拟太阳光进行光催化降解罗丹明B。结果发现,CdIn2S4/导电聚合物纤维复合材料的降解效率高于CdIn2S4粉体和Degussa P25 TiO2粉体,光催化降解3 h,罗丹明B的降解率为96.2%。     

甲苯对UASB反应器中溶解性微生物产物的影响

以乙酸钠为外加碳源,考察了UASB反应器内甲苯对可溶性微生物产物（SMP）的影响。实验结果表明：低质量浓度（20~70 mg/L）的甲苯对微生物有刺激作用,使得污泥增殖速率变小,SMP的质量浓度也逐渐减少,经过一段时间的驯化后,系统COD和TOC的去除率分别达到93%和94%以上,下降趋势较小;较高质量浓度（70~200 mg/L）的甲苯对微生物有抑制作用,污泥活性下降,反应器运行状况开始恶化,SMP的质量浓度也逐渐增大,经过一段时间的驯化后,系统COD和TOC的去除率分别维持在81%和83%以上;当甲苯质量浓度超过200 mg/L时,表现为污泥活性严重下降,对COD的去除效果极差。     

假单胞菌好氧降解四溴双酚A的特性

为了解四溴双酚A(TBBPA)的好氧降解特性,采用选择富集法从活性污泥中分离出一株能够高效降解四溴双酚A的菌株。根据其形态、生理生化特性及16S rDNA核苷酸序列分析,该菌株被鉴定为假单胞菌属(Pseudomonas sp.)。研究结果表明,该菌株可通过好氧共代谢方式实现四溴双酚A的降解,葡萄糖是四溴双酚A降解的最佳碳源,其最优降解条件为葡萄糖8 g/L,牛肉膏0.5 g/L,pH值为7.0,培养温度为35℃,摇床转速为150 r/min。在该条件下其生物降解过程符合一级动力学模型,6 d后的降解率高达95.6%。LC-MS结果表明,四溴双酚A在好氧降解过程中会生成异丙苯酚类物质。     

酸性矿井水中和沉淀法除铁优化

针对山西某煤矿高矿化度、高铁酸性矿井水除铁效果差、出水容易返色等问题,采用NaOH中和调pH、曝气及化学氧化等处理工艺进行酸性矿井水中和沉淀法除铁优化实验研究。结果表明,采用NaOH中和沉淀法除铁时,投加中和剂使出水pH达6.7以上时,出水中铁含量低于10 mg/L,满足排放要求。对于本实验废水NaOH所需投加量为2.8 g/L,铁的去除率可达到99.75%;以H2O2对原水进行氧化处理,可迅速将Fe(Ⅱ)氧化成Fe(Ⅲ),其用量与原水中Fe(Ⅱ)的含量成正比。当其用量为1.6 mL/L时,可将原水中的Fe(Ⅱ)完全转化为Fe(Ⅲ),投加中和剂使出水pH达到4.5以上时,能使出水中铁含量满足排放要求。对于实验废水所需的NaOH投加量为2.0 g/L,比直接中和沉淀所需的NaOH用量要节省28.6%。曝气处理对原水中Fe(Ⅱ)的氧化效果不明显。     

改性活性炭对水中铬离子(Ⅵ)的吸附性能

为了研究改性前后活性炭对水中铬离子(Ⅵ)的吸附效果,以磷酸活性炭(PAC)为原料,用10%硝酸改性得到硝酸改性活性炭(N-PAC)及直接蒸发法载铁改性得到载铁活性炭(Fe-PAC)。通过静态吸附研究表明,改性后活性炭对Cr(Ⅵ)的吸附率有较大提高。在常温、自然pH条件下,0.2 g活性炭处理50 mL浓度为100 mg/L的含Cr(Ⅵ)溶液,N-PAC和Fe-PAC对Cr(Ⅵ)的吸附率分别为79.21%和90.59%,都高于原PAC对Cr(Ⅵ)的吸附率49.58%。pH从2.2升高到11.92,Fe-PAC对Cr(Ⅵ)的吸附率从99.86%降低到14.77%,N-PAC则从99.86%降低到3.23%,PAC从97.05%降低到2.53%。温度从25℃升高到70℃,3种活性炭对Cr(Ⅵ)吸附率都有较大提高,都增加到98%以上。且吸附过程较符合Langmuir等温吸附模型。     

Classification and comparison of municipal solid waste based on thermochemical characteristics

Municipal solid waste (MSW) has been normally sorted into six categories, namely, food residue, wood waste, paper, textiles, plastics, and rubber. In each category, materials could be classified further into subgroups. Based on proximate and ultimate analysis and heating value, statistical methods such as analysis of variance (ANOVA) and cluster analysis were applied to analyze the characteristics of MSW in every subgroup and to try to distinguish their relative properties. The chemical characteristics analysis of MSW showed that polyethylene (PE), polypropylene (PP), and polystyrene (PS) had the highest volatile matter content, with almost no ash and fixed carbon, while polyethylene terephthalate (PET) had high carbon content but low hydrogen content. Bones and vegetables had the highest ash content, while nutshells and rubber had the highest fixed carbon content. Paper and starch food had the highest oxygen content, and wool and bones had the highest nitrogen and sulfur content. Polyvinyl chloride (PVC) had the highest chlorine content at about 55%. PE, PP, and PS had the highest heating value, followed by chemical products such as rubber and chemical fiber. Conversely, paper, vegetables and bones had the lowest heating value. The results of cluster analysis of MSW components showed that fruit peel, weeds, wood, bamboo, leaves and nutshells could be classified as the lignocellulose category; starch food, cotton, toilet paper, printing paper and cardboard could be classified as the glucose monomer category; wood and chemical fiber could be classified as the high nitrogen and sulfur category; and PE, PP, and PS could be cluster as the polyolefin category.

Implications: The yield of municipal solid waste (MSW) is constantly increasing and waste to energy (WTE) has been used extensively all over the world. During the processes of incineration, pyrolysis, or gasification, the impact of physical and chemical properties of MSW is of great significance. However, the traditional classification of MSW is too general to provide more detailed information in many investigations. It is necessary to perform the investigation of characteristics of combustible MSW to distinguish different categories of MSW and find out their subclassification.     

钛基金属氧化物电极的制备及性能

采用聚合物前驱体法制备了Ti/SnO₂-Sb₂O₃电极,再通过恒电流电沉积法制备了 Ti/SnO₂-Sb₂O₃/PbO₂和Ti/SnO₂-Sb₂O₃/MnO₂电极。采用SEM技术对3种金属氧化物电极表面的形貌进行了表征,并分别以3种电极为阳极进行了苯酚的电催化氧化实验。实验结果表明：电解时间为2.5 h时,Ti/SnO₂-Sb₂O₃电极、Ti/SnO₂-Sb₂O₃/PbO₂电极和Ti/SnO₂-Sb₂O₃/MnO₂电极对苯酚的降解率分别为85.9%,83.2%,44.6%;苯酚在3种电极上的电催化氧化反应均遵循一级反应动力学方程;苯酚在Ti/SnO₂-Sb₂O₃ 电极和Ti/SnO₂-Sb₂O₃/PbO₂电极上的反应速率较快,并具有较高的析氧电位;Ti/SnO₂-Sb₂O₃/PbO₂电极具有更好的耐腐蚀性和更长的使用寿命。