絮凝#x02014;微波辐射#x02014;Fenton试剂氧化法深度处理焦化废水

用絮凝#x02014;微波辐射#x02014;Fenton试剂氧化法深度处理焦化废水,研究了微波辐射时间、微波功率、FeSO₄加入量、H₂O₂加入量和废水pH对废水处理效果的影响。实验结果表明：在聚合氯化铝加入量为350mg/L、聚丙烯酰胺加入量为12mg/L、废水pH=5、FeSO₄加入量为250mg/L、H₂O₂总加入量为1400mg/L、H₂O₂分3次投加、微波功率为400W、微波辐射时间为60min的条件下,处理后出水的浊度、色度和COD去除率分别为98.59%,97.62%,86.21%。处理后出水澄清透明,COD为50.34mg/L,满足GB50050#x02014;2007《工业循环冷却水处理设计规范》的要求。     

3种运行模式下CAST工艺脱氮性能

以模拟城市污水为处理对象,采用循环式活性污泥法（CAST）反应器,对3种运行模式（M1：常规模式,M2：缺氧好氧模式、M3：缺氧好氧交替模式）下系统的脱氮性能进行了研究,比较了各模式下CAST反应器的氨氮和总氮的去除效率,并对各模式下典型周期内氮基质浓度变化进行了考察,以确定系统的脱氮模式。结果表明,在氨氮去除不成为限制条件（去除率〉90％）的条件下,3种运行模式下系统总氮的平均去除率分别为67．3％、70．6％和82．4％,以缺氧好氧交替模式下的最高;M1、M2和M3均可实现亚硝酸型硝化,但随着温度的升高,亚硝酸型硝化逐渐消失。静态实验分析表明,3种模式下系统的氨氧化速率大小次序为：vN：M1〉vN：M2〉vN：M3,反硝化速率大小次序为：vDN,M2〉vDN,M3〉vDN,M1。     

臭氧氧化法处理焦化废水生化出水的反应动力学简

对臭氧氧化去除焦化废水生化出水COD的反应动力学及其影响因素进行了实验研究,结果表明,在臭氧投加量为8.50 mg/min,反应温度为20℃和初始pH为10.61条件下,对COD的降解符合表观一级反应动力学模型,其相关系数R²=0.9991,表观反应速率常数k_Abs=1.01×10^-3 s^-1。该条件下,臭氧氧化对COD的降解主要来源于高活性羟基自由基的强氧化作用。在不同的臭氧投加量（4.25~12.75 mg/min）、不同的反应温度（10~40℃）和不同的初始pH（3.76~12.53）下,COD的降解也同样遵循一级反应动力学规律。随着臭氧投加量的增大,COD降解的表观反应速率常数从（0.554×10^-3） s^-1增加到（1.06×10^-3） s^-1;随着反应温度的升高,表观反应速率常数从（0.427×10^-3） s^-1增加到（1.40×10^-3） s^-1,温度越高反应速率提高的幅度却越小;在初始pH3.76~10.61范围内,表观反应速率常数从（0.218×10^-3） s^-1增加到（1.01×10^-3） s^-1,在初始pH为12.53时表观反应速率常数下降到（0.857×10^-3） s^-1。     

印染RO浓水深度处理及回用

采用Fenton-石灰苏打法耦合工艺对某印染厂印染反渗透(RO)浓水进行深度处理。通过实验研究了不同H2O2和Fe2+投加量、p H和反应时间对废水COD去除率的影响,以及不同石灰和碳酸钠投加量对废水硬度的脱除效果,出水回用于染色工段进行染色实验。结果表明,在p H=3.0,Fe2+投加量为1.5 mmol/L,H2O2投加量为3.75 mmol/L,反应时间为45 min,石灰和碳酸钠投加量分别为450 mg/L和1 000 mg/L的条件下,出水COD和硬度的去除率可分别达到73.9%和85.0%,耦合工艺出水水质符合该厂回用染色水标准,且减少了盐的使用,可实现印染RO浓水回用。     

Characterization of residue from leached cathode ray tube funnel glass: reutilization as white carbon black

Cathode ray tube (CRT) funnel glass remains an urgent environmental problem and is composed mainly of lead oxide and silicon oxide. In this research, the residue could be obtained from 2 h to 500 rpm activated CRT funnel glass after extracting lead via acid leaching under the conditions of HNO₃ concentration 1.0 mol/L, leaching temperature 95 °C and leaching time 1 h. In order to reutilize the residue, its physico-chemical properties were characterized by scanning electron microscopy, Brunauer–Emmett–Teller, thermogravimetric analysis, X-ray diffraction and Fourier transform infrared spectroscopy. The results indicated that the residue was an amorphous superfine powder with approximately 93 wt% silica oxide and specific surface area of more than 170 m²/g. It can be reutilized as white carbon black.     

Seasonal variation and spatial distribution of atmospheric mercury and its gas-particulate partition in the vicinity of a semiconductor manufacturing complex

This study investigated the tempospatial variation of atmospheric mercury and its gas-particulate partition in the vicinity of a semiconductor manufacturing complex, where a plenty of flat-monitor manufacturing plants using elemental mercury as a light-initiating medium to produce backlight fluorescence tubes and may fugitively emit mercury-containing air pollutants to the atmosphere. Atmospheric mercury speciation, concentration, and the partition of total gaseous mercury (TGM) and particulate mercury (Hg_p) were measured at four sites surrounding the semiconductor manufacturing intensive district/complex. One-year field measurement showed that the seasonal averaged concentrations of TGM and Hg_p were in the range of 3.30–6.89 and 0.06–0.14 ng/m³, respectively, whereas the highest 24-h TGM and Hg_p concentrations were 10.33 and 0.26 ng/m³, respectively. Atmospheric mercury apportioned as 92.59–99.01 % TGM and 0.99–7.41 % Hg_p. As a whole, the highest and lowest concentrations of TGM were observed in the winter and summer sampling periods, respectively, whereas the concentration of Hg_p did not vary much seasonally. The highest TGM concentrations were always observed at the downwind sites, indicating that the semiconductor manufacturing complex was a hot spot of mercury emission source, which caused severe atmospheric mercury contamination over the investigation region.     

Contamination of organochlorine pesticides in water and sediments from a waterbird-inhabited lake,East Central China

Seventeen organochlorine pesticides (OCPs) were investigated in the water and sediments from a waterbird-inhabited lake (Yangchaihu Lake) to evaluate their current pollution levels and potential risks. The concentrations of total OCPs in water and sediments were 10.12–59.75 ng/l and 4.25–27.35 ng/g dry weight, respectively. Hexachlorocyclohexanes (HCHs) and dichlorodiphenyltrichloroethanes (DDTs) were the most abundant OCPs, while HCB and cyclodiene pesticides were detected with low levels. Levels of ∑OCPs (sum of 17 OCPs) at sites highly influenced by waterbirds were significantly higher than the sites with no significant waterbird populations (one-way ANOVA, P?相似文献   

突变灰盖鬼伞过氧化物酶降解刚果红的响应面法优化分析简

酶法降解偶氮染料刚果红是一个复杂的过程,受温度、pH、酶量、刚果红浓度和双氧水浓度显著影响。为研究各因素及因素间交互作用对刚果红降解影响,提高刚果红的降解率,分别使用单因素法和响应面分析法对刚果红降解条件进行了优化。单因素实验结果显示灰盖鬼伞过氧化物酶降解刚果红的最适条件为：pH 5.0、32℃、酶量4.98 U、双氧水0.1 mmol/L、刚果红20 mg/L,此时刚果红最高降解率为34.84%。然后选双氧水浓度、刚果红浓度和灰盖鬼伞过氧化物酶量作为3个因素,通过中心组合设计实验,用响应面法对刚果红降解进行优化分析,最后得到一个拟合度良好的二次多项方程模型（R²=0.9900）。方差分析结果显示,刚果红浓度和酶量是影响最显著的因素,双氧水与酶以及染料与酶之间的交互作用极显著。响应面分析优化后的反应体系为：双氧水浓度0.15 mmol/L,刚果红浓度为27.21 mg/L,酶为2.0 7 U,在此条件下,刚果红降解率达58.13%。     

酸性洗涤塔-生物滤塔-生物曝气池组合工艺处理恶臭气体NH3和H2S

采用酸性洗涤塔、生物滤塔和生物曝气池的组合工艺处理NH3、H2S恶臭混合气体,研究表明,该组合工艺对NH3和H2S有很好的去除效果,在进气流量为35 L/min,喷淋量45 L/h时,NH3进气浓度50.15~525.4 mg/m3,H2S进气浓度10.23~110.36 mg/m3时,NH3单一进气去除率稳定在99%以上,H2S单一进气去除率90%以上。混合进气后,NH3去除率几乎为100%,H2S的去除率提高至98%以上。在一定的浓度范围内,NH3和H2S之间的相互作用对两者的去除效果没有明显的影响,而且起到了相互促进降解的作用。同时,进气流量和填料层高度都会影响NH3、H2S的去除率。系统对进气容积负荷变化的缓冲能力强,在偶尔超负荷条件下运行并不能使系统崩溃,并且微生物对高负荷逐渐表现出适应性。大部分溶于水的氨由生物曝气池去除,去除率达到96.9%。     

成都市某污水处理厂污泥处理与处置方式探讨

本文在简要介绍国内几种典型的污泥处理与处置方式基础上,结合成都市某污水处理厂在污泥处理与处置方面的现状以及所存在的问题,提出了以农业利用作为该厂污泥的最终处置方式。