机动车轮胎磨损颗粒物化学组分特征研究

为研究机动车道路行驶过程中轮胎磨损排放的颗粒物理化特性,利用轮胎轮廓仿真磨耗仪,对国内主流17种轮胎胎面进行仿真磨耗实验,获得颗粒物样品,提取并检测其中18种元素和20种多环芳烃（PAHs）的含量.结果显示,元素和PAHs含量因轮胎品牌和速度等级的不同而差异显著.18种元素平均含量为（99.04±68.43）mg/g,占样品总重的9.90%,其中Si（88.97±67.85）mg/g、Zn（6.77±1.64）mg/g和Na（1.05±0.75）mg/g的平均含量均超过1mg/g,Cd的含量最低,为（0.43±0.31）μg/g.20种PAHs含量之和（∑20PAHs）在12.13~433.64 μg/g,平均为（94.13±110.18）μg/g,PY的平均含量最高（30.98±31.27）μg/g,其次是CHR、BaP、FA、PHE和BghiP,平均含量最低的是AC（0.58±0.2）μg/g;从环数看,以4环PAHs为主（占∑20PAHs的45.03%~67.93%）,其次为3环（平均含量为15.45%）和5环（平均含量为12.62%）.总体来说,国外品牌轮胎样品中元素和PAHs含量略高于国内品牌,而主要PAHs环数略低于国内品牌.     

陕北不同沟道土地盐碱化现状及影响因素

沟道土地是陕北黄土丘陵沟壑区重要的土地资源。然而,当前对黄土高原沟道土地的盐碱化问题关注不够,对盐碱化的现状、发生机制和防治措施也缺乏深入系统的认识,知识储备不能满足生产实际的需要。本文以陕北黄土丘陵沟壑区自然和人为形成的沟道土地为研究对象,分别是延安顾屯新造耕地(治沟造地)、延川马家湾淤地坝土地和子洲黄土洼天然古聚湫土地,在这些流域内沿沟道采集土壤样品,测定土壤的电导率(EC)、p H值、含水量及粒度,分析土壤盐碱化的现状和影响因子。结果表明:马家湾淤地坝土地盐碱化最为严重,流域中游至上游均出现不同程度的盐碱化;顾屯新造地上游出现盐碱化,盐碱化程度较马家湾轻,而黄土洼古聚湫全流域未出现盐碱化。地下水位较浅是沟道土地发生盐碱化的主要影响因素,因此陕北沟道土地盐碱化防治应着力控制地下水位,建设良好的排水系统,加强排水。     

悬浮填料投加对AnMBR性能及膜污染的影响

研究了悬浮填料投加对分置式厌氧膜生物反应器（AnMBR）的COD去除效果、污泥混合液特性及膜污染的影响。试验结果表明:在反应器有机负荷为2.09 kg/（m3·d）,污泥负荷为0.54 kg/（kg·d）,水力停留时间（HRT）为48 h,温度为（35±2）℃的条件下,与未投加悬浮填料阶段比较,投加填料后AnMBR的COD总去除率由96.6%提高至97.9%,甲烷产率提高16.0%。同时投加悬浮填料后AnMBR混合液污泥平均粒径增大,滤饼层阻力、总阻力、滤饼层阻力在总阻力中的占比较未投加悬浮填料时分别降低7.8、6.5和1.3百分点,溶解性胞外聚合物（SEPS）和结合性胞外聚合物（BEPS）浓度分别降低了20.5%和29.4%,跨膜压差（TMP）线性增长速率降低,膜污染速率明显减缓。因此,投加悬浮填料可在不增加能耗的情况下改善污泥混合液特性,起到强化AnMBR处理效果和控制膜污染的作用。     

Preparation of hydrophobic hierarchical pore carbon–silica composite and its adsorption performance toward volatile organic compounds

Carbon–silica materials with hierarchical pores consisting of micropores and mesopores were prepared by introducing nanocarbon microspheres derived from biomass sugar into silica gel channels in a hydrothermal environment.The physicochemical properties of the materials were characterized by nitrogen physical adsorption(BET),scanning electron microscopy(SEM),and thermogravimetric(TG),and the adsorption properties of various organic waste gases were investigated.The results showed that microporous carbon materials were introduced successfully into the silica gel channels,thus showing the high adsorption capacity of activated carbon in high humidity organic waste gas,and the high stability and mechanical strength of the silica gel.The dynamic adsorption behavior confirmed that the carbon–silica material had excellent adsorption capacity for different volatile organic compounds(VOCs).Furthermore,the carbon–silica material exhibited excellent desorption characteristics:adsorbed toluene was completely desorbed at 150℃,thereby showing superior regeneration characteristics.Both features were attributed to the formation of hierarchical pores.     

Aerosol optical properties under different pollution levels in the Pearl River Delta (PRD) region of China

To clarify the aerosol hygroscopic growth and optical properties of the Pearl River Delta(PRD)region,integrated observations were conducted in Heshan City of Guangdong Province from October 19 to November 17,2014.The concentrations and chemical compositions of PM_(2.5),aerosol optical properties and meteorological parameters were measured.The mean value of PM_(2.5) increased from less than 35(excellent) to 35-75 μg/m~3(good) and then to greater than 75 μg/m~3(pollution),corresponding to mean PM_(2.5) values of 24.9,51.2,and 93.3 μg/m~3,respectively.The aerosol scattering hygroscopic growth factor(f(RH = 80%)) values were 2.0,2.12,and 2.18 for the excellent,good,and pollution levels,respectively.The atmospheric extinction coefficient(σext)and the absorption coefficient of aerosols(σ_(ap)) increased,and the single scattering albedo(SSA)decreased from the excellent to the pollution levels.For different air mass sources,under excellent and good levels,the land air mass from northern Heshan had lower f(RH) and σ_(sp) values.In addition,the mixed aerosol from the sea and coastal cities had lower f(RH) and showed that the local sources of coastal cities have higher scattering characteristics in pollution periods.     

Tuning the fill percentage in the hydrothermal synthesis process to increase catalyst performance for ozone decomposition

The performance of Ce-OMS-2 catalysts was improved by tuning the fill percentage in the hydrothermal synthesis process to increase the oxygen vacancy density. The Ce-OMS-2 samples were prepared with different fill percentages by means of a hydrothermal approach (i.e. 80%, 70%, 50% and 30%). Ce-OMS-2 with 80% fill percentage (Ce-OMS-2-80%) showed ozone conversion of 97%, and a lifetime experiment carried out for more than 20?days showed that the activity of the catalyst still remained satisfactorily high (91%). For Ce-OMS-2-80%, Mn ions in the framework as well as K ions in the tunnel sites were replaced by Ce⁴⁺, while for the others only Mn ions were replaced. O₂-TPD and H₂-TPR measurements proved that the Ce-OMS-2-80% catalyst possessed the greatest number of mobile surface oxygen species. XPS and XAFS showed that increasing the fill percentage can reduce the AOS of Mn and augment the amount of oxygen vacancies. The active sites, which accelerate the elimination of O₃, can be enriched by increasing the oxygen vacancies. These findings indicate that increasing ozone removal can be achieved by tuning the fill percentage in the hydrothermal synthesis process.     

Regulated emission characteristics of in-use LNG and diesel semi-trailer towing vehicles under real driving conditions using PEMS

On-road driving emissions of six liquefied natural gas(LNG) and diesel semi-trailer towing vehicles(STTVs) which met China Emission Standard IV and V were tested using Portable Emission Measurement System(PEMS) in northern China.Emission characteristics of these vehicles under real driving conditions were analyzed and proved that on-road emissions of heavy-duty vehicles(HDVs) were underestimated in the past.There were large differences among LNG and diesel vehicles, which also existed between China V vehicles and China IV vehicles.Emission factors showed the highest level under real driving conditions, which probably be caused by frequent acceleration, deceleration, and start-stop.NOx emission factors ranged from 2.855 to 20.939 g/km based on distance-traveled and 6.719–90.557 g/kg based on fuel consumption during whole tests, which were much higher than previous researches on chassis dynamometer.It was inferred from tests that the fuel consumption rate of the test vehicles had a strong correlation with NOx emission, and the exhaust temperature also affected the efficiency of Selected Catalytic Reduction(SCR) aftertreatment system, thus changing the NOx emission greatly.THC emission factors of LNG vehicles were 2.012–10.636 g/km, which were much higher than that of diesel vehicles(0.029–0.185 g/km).Unburned CH_4 may be an important reason for this phenomenon.Further on-road emission tests, especially CH_4 emission test should be carried out in subsequent research.In addition, the Particulate Number(PN) emission factors of diesel vehicles were at a very high level during whole tests, and Diesel Particulate Filter(DPF)should be installed to reduce PN emission.     

中国工业园区绿色发展政策对比分析及对策研究

为了提升我国工业园区绿色发展水平,对目前我国工业园区发展历程、现状特征进行了分析,对工业园区绿色发展政策进行了梳理和对比,并结合工业园区绿色发展中存在的问题提出了对策建议.研究表明:①我国工业园区经历了快速发展、调整发展和科学发展等阶段,在经济发展、资源与能源优化利用、污染减排等方面成效显著.②我国工业园区绿色发展的相关政策主要体现在国家生态工业示范园区创建、园区循环化改造、国家低碳工业园区试点、绿色园区建设和UNIDO绿色工业园区创建等工作中,这些政策在推动主体、实施路径、侧重方向上各不相同又各有特色,对推动工业园区节能减排绩效明显.③目前,我国工业园区绿色发展存在的问题主要表现在重视程度有待提升、风险防范意识有待加强、创新能力有待提高等方面.为此,提出了我国工业园区绿色发展对策建议:积极践行绿色发展理念,推进园区绿色化、生态化、低碳化建设,实现经济环境双赢;注意环境风险防控,确保环境安全;创新管理机制,强化监督管理.      

Hygroscopicity measurement of sodium carbonate, β-alanine and internally mixed β-alanine/Na2CO3 particles by ATR-FTIR

Water-uptakes of pure sodium carbonate(Na_2CO_3),pure β-alanine and internally mixedβ-alanine/Na_2CO_3 aerosol particles with different mole ratios are first monitored using attenuated total reflectance Fourier transform infrared spectroscopy(ATR-FTIR) technique.For pure Na_2CO_3 aerosol particles,combining the absorptions at 877 and 1422 cm-1 with abrupt water loss shows the efflorescence relative humidity(ERH) of 62.9%–51.9%.Upon humidifying,solid Na_2CO_3 firstly absorbs water to from Na_2CO_3·H2 O crystal at 72.0% RH and then deliquesces at 84.5% RH(DRH).As for pure β-alanine particles,the crystallization takes place in the range of 42.4%–33.2% RH and becomes droplets at ～ 88.2% RH.When β-alanine is mixed with Na_2CO_3 at various mole ratios,it shows no efflorescence of Na_2CO_3 whenβ-alanine to Na_2CO_3 mole ratio(OIR) is 2:1.For 1:1 and 1:2 β-alanine/Na_2CO_3 aerosols,the ERHs of Na_2CO_3 are 51.8%–42.3% and 57.1%–42.3%,respectively.While β-alanine crystal appears from 62.7% RH for 2:1 and 59.4% RH for both 1:1 and 1:2 particles and lasts to driest state.On hydration,the DRH is 44.7%–75.2% for Na_2CO_3 with the OIR of 1:1 and 44.7%–69.0%for 1:2 mixture,and those of β-alanine are 74.8% for 2:1 mixture and 68.9% for two others.After the first dehumidification–humidification,all the water contents decrease despite of constituent fraction.And at ～ 92% RH,the remaining water contents are 92%,89% and 82%at ～ 92% RH,corresponding to OIR of 2:1,1:1 and 1:2 mixed system,respectively.     

Dynamic nano-Ag colloids cytotoxicity to and accumulation by Escherichia coli: Effects of Fe3+, ionic strength and humic acid

Released Ag ions or/and Ag particles are believed to contribute to the cytotoxicity of Ag nanomaterials, and thus, the cytotoxicity and mechanism of Ag nanomaterials should be dynamic in water due to unfixed Ag particle:Ag⁺ ratios. Our recent research found that the cytotoxicity of PVP-Ag nanoparticles is attributable to Ag particles alone in 3 hr bioassays, and shifts to both Ag particles and released Ag⁺ in 48 hr bioassays. Herein, as a continued study, the cytotoxicity and accumulation of 50 and 100 nm Ag colloids in Escherichia coli were determined dynamically. The cytotoxicity and mechanisms of nano-Ag colloids are dynamic throughout exposure and are derived from both Ag ions and particles. Ag accumulation by E. coli is derived mainly from extracellular Ag particles during the initial 12 hr of exposure, and thereafter mainly from intracellular Ag ions. Fe³⁺ accelerates the oxidative dissolution of nano-Ag colloids, which results in decreasing amounts of Ag particles and particle-related toxicity. Na⁺ stabilizes nano-Ag colloids, thereby decreasing the bioavailability of Ag particles and particle-related toxicity. Humic acid (HA) binds Ag⁺ to form Ag⁺-HA, decreasing ion-related toxicity and binding to the E. coli surface, decreasing particle-related toxicity. HA in complex conditions showed a stronger relative contribution to toxicity and accumulation than Na⁺ or Fe³⁺. The results highlighted the cytotoxicity and mechanism of nano-Ag colloids are dynamic and affected by environmental factors, and therefore exposure duration and water chemistry should be seriously considered in environmental and health risk assessments.