pH过程控制对铁炭微电解-Fenton影响中试研究

采用铁炭微电解-Fenton联合工艺处理制药废水生化出水,探讨了初始pH对微电解过程COD降解速率、出水中Fe2+和Fe3+变化规律以及后续Fenton氧化效果的影响,为优化联合工艺提出了微电解反应pH过程控制的理论。采用pH过程控制时,微电解对COD降解速率大大提高,降解过程基本符合零级反应动力学,同时可大大提高Fe2+和Fe3+浓度及总铁析出量。试验结果表明:当初始pH=2.5,以3.0L/h连续性投加稀硫酸100 min,曝气微电解反应2 h,出水再投加1.0mL/L的H2O2进行Fenton氧化2 h,出水COD总去除率可达85.6%;采用pH过程控制可将微电解出水ρ(Fe2+)浓度从48.6 mg/L提高至149 mg/L,COD降解速率从10.9 mg/(L·h)提高至23.8 mg/(L·h)。     

餐厨垃圾与污水污泥共消化产酸试验研究

研究了餐厨垃圾与污水污泥在不同混合比例、不同污泥停留时间条件下的共消化产酸效果。试验结果表明:当餐厨垃圾与污水污泥TS比为1∶3时,SRT=1 d的反应器酸化效率最高,且乙酸含量占优,产酸效果较佳;当TS之比为1∶1时,各反应器产酸量普遍高于1∶3时,其中SRT=5 d产酸反应器,最高酸化效率达5.94,产酸量最大,且乙酸含量占优,运行效果最佳。     

改性凹凸棒土吸附地下水中硝基苯的实验研究

从凹凸棒土(以下简称凹土)的有机改性入手,研究凹土的十六烷基三甲基溴化铵(CTAB)、十八烷基三甲基氯化铵(OTAC)改性及吸附模拟硝基苯(nitrobenzene,NB)污染地下水的影响因素及性能。结果表明:采用超声改性法制得的CTAB、OTAC改性凹土对地下水中NB具有较强的吸附能力,每100g凹土改性剂最佳用量为30 mmol。在NB浓度为20mg/L、投加量为4%、吸附时间30 min的条件下,NB吸附去除率分别达45.68%、55.40%;改性凹土的静态吸附行为符合Langmuir吸附等温方程。     

基于臭氧溶胞的活性污泥减量化技术

目前常见的活性污泥减量技术主要包括解偶联技术、微生物的捕食作用以及隐性生长三种方法。基于臭氧氧化溶胞作用从而强化细菌隐性生长的污泥减量技术具有较好的处理效果及良好的应用前景。着重探讨了臭氧溶胞作用的机理及溶胞过程的影响因素。考虑到污泥减量技术在实际污水处理系统中的应用,探讨了臭氧溶胞对污水生物处理系统的影响。     

Simultaneous preconcentration of cadmium and lead in water samples with silica gel and determination by flame atomic absorption spectrometry

A new method that utilizes pretreated silica gel as an adsorbent has been developed for simultaneous preconcentration of trace Cd(II) and Pb(II) prior to the measurement by flame atomic absorption spectrometry. The effects of pH, the shaking time, the elution condition and the coexisting ions on the separation/preconcentration conditions of analytes were investigated. Under optimized conditions, the static adsorption capacity of Cd(II) and Pb(II) were 45.5 and 27.1mg/g, the relative standard deviations were 3.2% and 1.7% (for n = 11), and the limits of detection obtained were 4.25 and 0.60 ng/mL, respectively. The method was validated by analyzing the certified reference materials GBW 07304a (stream sediment) and successfully applied to the analysis of various treated wastewater samples with satisfactory results.     

Analytical model of metalworking fluid penetration into the flank contact zone in orthogonal cutting

Metalworking fluids (MWFs) are used widely in machining process to dissipate heat, lubricate moving surfaces, and clear chips. They have also been linked to a number of environmental and worker health problems. To reduce these impacts, minimum quantity lubrication (MQL) sprays of MWF delivered in air or CO₂ have been proposed. MQL sprays can achieve performance comparable with conventional water-based or straight oil MWFs while only delivering a small fraction of the fluid. This performance advantage could be explained by the enhanced penetration into the cutting zone that results from delivering MWF in high pressure and precise sprays. To explore this hypothesis, an analytical model of MWF penetration into the flank face of the cutting zone is developed and validated using experimental data. The model is based on a derivation of the Navier–Stokes equation and the Reynolds equation for lubrication and applied to an orthogonal cutting geometry under steady-state conditions. A solution to the model is obtained using a numerical strategy of discretizing the analytical scheme with two-dimensional centered finite difference method. Penetration into the cutting zone is estimated for MQL sprays delivered in air, CO₂ and N₂ as well as two conventional MWFs, straight oil and semi-synthetic emulsion. The model suggests that conventional MWFs, do not penetrate the cutting zone fully and fail to provide direct cooling to the flank zone where wear is most likely to occur. MQL sprays do penetrate the cutting zone completely. Using convective heat transfer coefficients from a previous study, a finite element heat balance is carried out on the tool to understand how each fluid impacts temperature near the flank tip of the tool. The results of the modeling effort are consistent with experimental measurements of tool temperature during turning of titanium (6AL4V) using a K313 carbide tool. The prediction of temperature near the flank indicates that MQL sprays do suppress temperatures near the flank effectively. These results help explain the low levels of tool wear observed for some MQL sprays, particularly those based on high pressure CO₂. This modeling framework provides valuable insight into how lubricant delivery characteristics such as speed, viscosity, and cutting zone geometry can impact lubricant penetration.     

Tool wear of coated drills in drilling CFRP

This study aimed to investigate the wear of certain coated drills when drilling carbon fiber reinforced composites (CFRP). Three different drills were used in the drilling experiments: uncoated, diamond coated and AlTiN coated carbide (WC–Co) drills. The tool wear in CFRP machining was quite different from that in conventional metal machining. The primary wear type was a dulling or blunting of the cutting edge, which has been referred to as edge rounding wear or edge recession. In this paper, a hypothesis has been developed to explain the edge rounding wear in CFRP machining. Due to the fracture-based chip formation of CFRP, there is lack of the work material stagnation zone in front of the cutting edge, which normally prevents the edge wear in metal machining. Series of wear lead to rapid dulling of the cutting edge. The resistance to edge rounding wear on the coated as well as uncoated drills has been investigated. The diamond coating significantly reduces the edge rounding wear. However, AlTiN coated drills showed no visible improvement over the uncoated carbide drill, despite of their high hardness, thus not protecting the drill. The wear mechanisms of the uncoated carbide drill and coatings are discussed. It is believed that the 2-body and 3-body abrasive wear fail to explain the observed tool wear in CFRP drilling. However, the wear of the coatings and uncoated carbide substrate from tribo-meter tests correlated well with the tool wear in the CFRP drilling. Therefore, the tribo-meter test can be used to screen the prospective tool materials before carrying drilling experiment.     

浅谈可燃气体报警器检定装置计量标准的建立

从计量标准的相关概念出发．强调了建立可燃气体报警器计量检定装置（计量标准）的目的和重要性。从计量标准的工作原理、计量标准器及配套设备构成、计量标准的测量范围、重复性、稳定性、不确定度等计量技术角度对可燃气体报警器检定装置的建立进行了阐述。     

宏基因组技术在土壤污染微生物修复中的应用

微生物修复在土壤污染治理中具有重要地位。虽然环境中可以培养的微生物比例很低,但微生物的基因资源十分丰富,运用宏基因组技术可以克服传统修复技术中微生物资源利用不充分的问题,为未培养微生物的研究提供了有力手段。本文对宏基因组技术一般流程作了介绍,并结合土壤污染的特点,对该技术应用在土壤污染微生物修复的现状、研究及展望作了阐述。     

测定总氮中影响因素的探讨

本文研究了过硫酸钾氧化紫外分光光度法测定总氮的过程中,通过标准曲线、标准物质、具体试样的一系列测定探讨,发现试剂、实验用水、实验器皿、实验环境等对测定结果有很大影响。