用于磷吸附的载铁(β-FeOOH)沸石制备及特性简

以天然沸石为载体,采用FeCl₃水解法制备用于磷吸附的载铁沸石（β-FeOOH-Z）,优化β-FeOOH-Z的制备条件,包括FeCl₃溶液浓度、负载pH值、负载时间、负载温度和烘干温度,并利用X射线衍射（XRD）和傅里叶变换红外光谱（FTIR）对β-FeOOH-Z及其磷吸附特性进行分析。结果表明,β-FeOOH-Z的优化制备条件为：FeCl₃溶液浓度1 mol/L、负载pH值6、负载时间24 h、负载温度25℃和烘干温度60℃。优化制备条件下,100~120目沸石的载铁量为100.2 mg/g,铁的负载率为18%,其磷吸附量为7.68 mg/g,比天然沸石提高79.6%。XRD分析结果表明,β-FeOOH-Z中的杂质元素较天然沸石减少,并有效负载β-FeOOH;制备条件对β-FeOOH-Z的成分有较大影响,FeCl₃溶液浓度较低、负载温度和烘干温度过高均使β-FeOOH-Z中含有α-Fe₂O₃,并导致其磷吸附效率降低。FTIR分析结果表明,β-FeOOH-Z的表面羟基在其吸附磷过程中起重要作用,羟基与磷酸根离子的配位交换是β-FeOOH-Z吸附磷的主要作用机制。     

Manganese concentrations in maternal–infant blood and birth weight

Manganese (Mn) is an essential mineral nutrient in mammals. The physiological role of Mn in animal models is well documented, but little is known about the adverse effects of Mn deficiency or overexposure in humans, including pregnancy outcomes such as birth weight. We examined the relationship of the maternal and cord blood Mn levels with birth weight in a cohort of 172 mother–infant pairs born in Shanghai, China. Non-linear spline and quadratic regression models were used to test the hypothesis of an inverted U-shaped association between the Mn levels and birth weight. The median (range) levels of Mn in the maternal and cord blood were 5.38 (2.34–30.37) μg/dL and 7.66 (2.57–34.23) μg/dL, respectively. An inverted U-shaped relationship was observed between maternal Mn and birth weight after adjusting for potential confounders. The birth weight increased with Mn levels up to 4.18 μg/dL, and a slight reduction in weight was observed at higher levels. The cord blood Mn levels were not found to be associated with birth weight. Both lower and higher Mn exposures are associated with lower birth weight, which may influence important developmental parameters; the association of higher Mn levels with lower weight was weak and imprecise.     

磷石膏水热法合成硫酸钙晶须

以磷石膏为原料,二水合硫酸钙、硫酸镁、甘油为添加剂,采用水热法合成硫酸钙晶须,考察了料浆含量、反应温度、反应时间、体系pH等因素对晶须的直径和长径比的影响;并采用SEM技术观察硫酸钙晶须的形貌。实验结果表明,当磷石膏含量2.5%（w）、反应温度130 ℃、反应时间4 h、体系pH 4时,制备得到的硫酸钙晶须长径比为56.24,平均直径为0.17 μm。SEM表征结果显示,硫酸钙晶须形貌规整、分散均匀、直径较小,达百纳米级。     

镍基催化剂对污泥微波热解制生物气效能的影响

为实现污水污泥减量化、无害化及资源化的目标,在微波热解污水污泥基础上,进行了镍基催化剂对制取生物气效能影响的研究。采用元素分析对污泥元素进行检测,气/质联用分析(GC-MS)和气相色谱(GC)对热解生物气的组成和含量进行测定。实验结果表明,镍基催化剂的添加对微波热解污水污泥制取生物气有较大促进作用。5%添加量与800℃热解终温条件下具有最佳催化效果:生物气中H2、CO产量最大,H2产量由29 g/kg增加到35.8 g/kg,提升23.4%,CO产量由302.7 g/kg增加到383.3 g/kg,提升26.6%;同时催化剂还能提高热能利用效率,降低热解终温,即5%添加量在700℃热解终温时可达到空白800℃时的产气效果;镍基催化剂主要在500~600℃时发挥催化作用,加快了H2和CO的释放。微波热解污泥制取的生物气具有产量大、富含H2与CO等优点,可推动污水污泥的资源化进程。     

溴酸钾对二茂铁(Fc)非均相Fenton效能的影响

研究了KBrO3对二茂铁(Fc)非均相Fenton效能的影响,深入考察了KBrO3对体系中Fc溶解、H2O2分解和羟基自由基(·OH)生成的影响。结果表明,KBrO3的加入对不同反应阶段Fc/Fenton体系的效能均有明显的促进作用,初始阶段主要是由于KBrO3对·OH产生的促进作用所致,后期主要是由于KBrO3促进了体系中Fc的溶解,使得体系中溶解态的Fc催化的均相Fenton反应的比例增加,体系中H2O2的分解加快,·OH的表观生成率增加,进而促进了反应的进行。无KBrO3添加,pH=4,MB初始浓度为10 mg/L,Fc的量为1.6×10-3mol/L,[H2O2]/[MB]=3.14时,45 min时,MB的剩余率为9.1%,105 min时为0。当KBrO3的用量为3×10-4mol/L时,反应45 min后MB的去除率即可达到100%。随着KBrO3浓度的增加,其对Fc/Fenton效能的促进作用增强。     

发酵类抗生素废水处理工艺及运行效果

介绍了内蒙古某抗生素废水处理厂的处理工艺流程、处理单元类型及其详细设计参数,通过对该污水处理厂半年内运行效果的调研,分析评价该污水处理系统的处理效果及出水指标;该水厂工艺流程对COD、TOC、氨氮、总氮、总磷、BOD和急性毒性的平均去除率分别为96.52%、95.83%、50.24%、55.20%、62.05%、98.52%和99.14%,COD、氨氮、总氮、总磷出水水质分别为477、438、556.7和7.69 mg/L,达到排放到城区下水道要求,园区内所有废水汇集到园区污水处理厂进行集中深度处理达标后排放水体。通过对该水厂工艺的介绍和水质分析,为我国抗生素生产企业面临的废水处理工艺类型选择及工程改造升级提供一定参考。     

酸性洗涤塔-生物滤塔-生物曝气池组合工艺处理恶臭气体NH3和H2S

采用酸性洗涤塔、生物滤塔和生物曝气池的组合工艺处理NH3、H2S恶臭混合气体,研究表明,该组合工艺对NH3和H2S有很好的去除效果,在进气流量为35 L/min,喷淋量45 L/h时,NH3进气浓度50.15~525.4 mg/m3,H2S进气浓度10.23~110.36 mg/m3时,NH3单一进气去除率稳定在99%以上,H2S单一进气去除率90%以上。混合进气后,NH3去除率几乎为100%,H2S的去除率提高至98%以上。在一定的浓度范围内,NH3和H2S之间的相互作用对两者的去除效果没有明显的影响,而且起到了相互促进降解的作用。同时,进气流量和填料层高度都会影响NH3、H2S的去除率。系统对进气容积负荷变化的缓冲能力强,在偶尔超负荷条件下运行并不能使系统崩溃,并且微生物对高负荷逐渐表现出适应性。大部分溶于水的氨由生物曝气池去除,去除率达到96.9%。     

The Importance of Temporal and Spatial Vegetation Structure Information in Biotope Mapping Schemes: A Case Study in Helsingborg,Sweden

Temporal and spatial vegetation structure has impact on biodiversity qualities. Yet, current schemes of biotope mapping do only to a limited extend incorporate these factors in the mapping. The purpose of this study is to evaluate the application of a modified biotope mapping scheme that includes temporal and spatial vegetation structure. A refined scheme was developed based on a biotope classification, and applied to a green structure system in Helsingborg city in southern Sweden. It includes four parameters of vegetation structure: continuity of forest cover, age of dominant trees, horizontal structure, and vertical structure. The major green structure sites were determined by interpretation of panchromatic aerial photographs assisted with a field survey. A set of biotope maps was constructed on the basis of each level of modified classification. An evaluation of the scheme included two aspects in particular: comparison of species richness between long-continuity and short-continuity forests based on identification of woodland continuity using ancient woodland indicators (AWI) species and related historical documents, and spatial distribution of animals in the green space in relation to vegetation structure. The results indicate that (1) the relationship between forest continuity: according to verification of historical documents, the richness of AWI species was higher in long-continuity forests; Simpson’s diversity was significantly different between long- and short-continuity forests; the total species richness and Shannon’s diversity were much higher in long-continuity forests shown a very significant difference. (2) The spatial vegetation structure and age of stands influence the richness and abundance of the avian fauna and rabbits, and distance to the nearest tree and shrub was a strong determinant of presence for these animal groups. It is concluded that continuity of forest cover, age of dominant trees, horizontal and vertical structures of vegetation should now be included in urban biotope classifications.     

固体厌氧消化原料流变特性研究综述

厌氧消化原料的流变特性是厌氧消化工艺设计和运行的重要参数。本文从研究对象、实验操作、研究内容和结果、影响因素以及发展方向等方面对固体厌氧消化原料,特别是污泥的流变特性研究现状进行了概述。研究表明,污泥来源广泛,成分复杂,属于非牛顿流体的范畴,其流变特性受多种因素影响,其中污泥的总悬浮固体(TSS)(或混合液悬浮固体(MLSS))和温度是最主要的影响因素。大部分研究采用层流剪切实验对物料的流变特性进行表征,研究对象范围有待于扩大。尚需针对流体本构方程的改进,共消化对于原料流变特性的影响,混合液固、液相指标与流变参数的关系等方面开展研究,为利用流变参数作为工艺控制参数提供理论依据,并解决工程放大等问题。     

回收与降解聚驱采出水的工艺探讨

含聚污水的处理是困扰石油行业的难题之一。基于聚驱采出水的特点,围绕聚合物的回收利用和降解理论及技术,探讨国内外含聚污水处理技术的研究与应用现状,对比分析现有处理技术存在的问题及适应性,提出采用化学混凝、气浮和水质改性等技术来回收利用PAM(聚丙烯酰胺)的新思路,打破了降解PAM的传统思维,同时分析含聚污水处理与利用技术的可行性与应用前景,有望实现含聚污水的循环利用。