旋转式滗水器设计的动力学计算

在对旋转式滗水器进行了水力学和运动学计算的基础上，对旋转式滗水器进行了动力学计算，给出了其动力学计算公式，与水力学和运动学计算公式一起，共同给出了旋转式滗水器完整的设计计算公式。     

中国南方某城市自来水厂处理工艺对多环芳烃的去除效果研究

讨论了中国南方某城市自来水厂饮用水中的多环芳烃残留规律以及现有净水工艺对多环芳烃的去除效果。研究结果表明,该自来水厂饮用水中检出多环芳烃以2~4环芳烃为主,强致癌性高环数多环芳烃均在检出限以下,且多环芳烃总量未超出中国供水行业标准(2000年)的相关限值。各处理工艺段中,砂滤过程对多环芳烃的去除效果最好,相较于原水对多环芳烃总量的去除率可达64%。     

微囊藻毒素污染控制技术的研究进展

主要对水环境中微囊藻毒素污染的产生、毒性和去除方法进行了综述,在如何高效去除MCs方面具有重要意义.     

人工湿地处理系统中多环芳烃的行为

采用Oasis HLB柱固相萃取的前处理技术,以气相色谱质谱联用仪(GC/MS)的分析方法,对我国北方永定河上游黑土洼人工湿地中多环芳烃污染的特征以及分布规律进行了研究.结果表明,该湿地系统以低环数多环芳烃污染为主,其中浓度最高的是菲和蒽,未检出高环数(5环、6环)多环芳烃.通过比较进水和出水的浓度,湿地系统总体上不能有效去除进水中的多环芳烃.但是比较不同工艺单元进出水浓度,复氧、植物根系及微生物等均影响到多环芳烃的去除效果,去除率在28%～65%之间.     

各种影响因子对电解法预处理医药废水的影响研究

探讨了电解法预处理医药废水时停留时间、电解电压、废水初始浓度、温度和废水pH值等影响因子对去除色度、COD和提高废水可生化性等处理效果的影响，并考察了其应用于工业实际废水处理的可行性。实验结果表明：电解法更适合高浓度医药废水的处理，色度的去除率可达到90％以上；电解时间宜控制在40-60min；电解电压越高，废水COD和色度去除效果越好；在实验温度范围内，温度对色度和COD去除率的影响不大；废水pH值为7．5时电解效果最佳，工程运用宜控制在6—9之间。     

人工湿地处理系统中多环芳烃的行为

采用Oasis HLB柱固相萃取的前处理技术,以气相色谱质谱联用仪（GC/MS）的分析方法,对我国北方永定河上游黑土洼人工湿地中多环芳烃污染的特征以及分布规律进行了研究.结果表明,该湿地系统以低环数多环芳烃污染为主,其中浓度最高的是菲和蒽,未检出高环数（5环、6环）多环芳烃.通过比较进水和出水的浓度,湿地系统总体上不能有效去除进水中的多环芳烃.但是比较不同工艺单元进出水浓度,复氧、植物根系及微生物等均影响到多环芳烃的去除效果,去除率在28%～65%之间.     

水污染·水资源·对策

本文详细论述了中国和世界的水资源状况，并论述了中国的水资源短缺状况、中国用水的优劣势，以及如何解决中国水资源短缺的措施和基本战略。     

低温等离子体治理H2S污染的实验研究

低温等离子体技术是一种高效、快速的污染消除技术，国内外都在对其进行广泛而深入的研究。采用脉冲电晕放电等离子体对空气中的硫化氢进行降解研究，探索了、脉冲峰压、脉冲频率、气体流量以及气体初始浓度对净化效果的影响，气体浓度由气相色谱仪测定。结果表明，脉冲电晕放电可以有效消除硫化氢污染，净化率随脉冲峰压和脉冲频率的增加而提高，随气体初始浓度和流量的增加而下降，且在初始浓度360mg／m^2、流量1200mL／min、脉冲峰压30kV、脉冲频率80Hz的条件下，处理后的气体中已检测不到H2S，根据色谱检测限（0．29mg／m^3）计算出的净化率≥99．92％。采用离子色谱对产物进行了定性分析，发现H2S经放电处理后主要产物为SO2和SO3。     

挥发性有机硫化合物释放的研究与展望

在介绍硫的生物地球化学循环的基础上，概述了几种挥发性有机硫气体ＤＭＳ，ＣＯＳ，ＭＳＨ，ＣＳ２和ＤＭＤＳ从各种自然源（主要是生物源）释放的情况，着重阐述了陆地生态系统中各种生物硫源的释放情况，列举了测定这些释放的硫通量的方法，并且对有机硫气体的大气行为及环境影响也作了论述。     

The styrene purification performance of biotrickling filter with toluene-styrene acclimatization under acidic conditions

The obvious disadvantages of biotrickling filters (BTFs) are the long start-up time and low removal efficiency (RE) when treating refractory hydrophobic volatile organic compounds (VOCs), which limits its industrial application. It is worthwhile to investigate how to reduce the start-up period of the BTF for treating hydrophobic VOCs. Here, we present the first study to evaluate the strategy of toluene induction combined with toluene-styrene synchronous acclimatization during start-up in a laboratory-scale BTF inoculated with activated sludge for styrene removal, as well as the effects of styrene inlet concentration (0.279 to 2.659 g·m^?3), empty bed residence time (EBRT) (i.e., 136, 90, 68, 45, 34 sec), humidity (7.7% to 88.9%), and pH (i.e., 4, 3, 2.5, 2) on the performance of the BTF system. The experiments were carried out under acidic conditions (pH 4.5) to make fungi dominant in the BTF. The start-up period for styrene in the BTF was shortened to about 28 days. A maximum elimination capacity (EC_max) of 126 g·m^?3·hr^?1 with an RE of 80% was attained when styrene inlet loading rate (ILR) was below 180 g·m^?3·hr^?1. The highest styrene RE(s) [of BTF] that could be achieved were 95% and 93.4%, respectively, for humidity of 7.7% and at pH 2. A single dominant fungal strain was isolated and identified as Candida palmioleophila strain MA-M11 based on the 26S ribosomal RNA gene. Overall, the styrene induction with the toluene-styrene synchronous acclimatization could markedly reduce the start-up period and enhance the RE of styrene. The BTF dominated by fungi exhibited good performance under low pH and humidity and great potential in treating styrene with higher inlet concentrations.

Implications: The application of the toluene induction combined with toluene-styrene synchronous acclimatization demonstrated to be a promising approach for the highly efficient removal of styrene. The toluene induction can accelerate biofilm formation, and the adaptability of microorganisms to styrene can be improved rapidly by the toluene-styrene synchronous acclimatization. The integrated application of two technologies can shorten the start-up period of biotrickling filters markedly and promote its industrial application.