Biodegradation of methyl red by Bacillus sp. strain UN2: decolorization capacity,metabolites characterization,and enzyme analysis

Azo dyes are recalcitrant and refractory pollutants that constitute a significant menace to the environment. The present study is focused on exploring the capability of Bacillus sp. strain UN2 for application in methyl red (MR) degradation. Effects of physicochemical parameters (pH of medium, temperature, initial concentration of dye, and composition of the medium) were studied in detail. The suitable pH and temperature range for MR degradation by strain UN2 were respectively 7.0–9.0 and 30–40 °C, and the optimal pH value and temperature were respectively 8.0 and 35 °C. Mg²⁺ and Mn²⁺ (1 mM) were found to significantly accelerate the MR removal rate, while the enhancement by either Fe³⁺ or Fe²⁺ was slight. Under the optimal degradation conditions, strain UN2 exhibited greater than 98 % degradation of the toxic azo dye MR (100 ppm) within 30 min. Analysis of samples from decolorized culture flasks confirmed biodegradation of MR into two prime metabolites: N,N′dimethyl-p-phenyle-nediamine and 2-aminobenzoic acid. A study of the enzymes responsible for the biodegradation of MR, in the control and cells obtained during (10 min) and after (30 min) degradation, showed a significant increase in the activities of azoreductase, laccase, and NADH-DCIP reductase. Furthermore, a phytotoxicity analysis demonstrated that the germination inhibition was almost eliminated for both the plants Triticum aestivum and Sorghum bicolor by MR metabolites at 100 mg/L concentration, yet the germination inhibition of parent dye was significant. Consequently, the high efficiency of MR degradation enables this strain to be a potential candidate for bioremediation of wastewater containing MR.     

氯化镁复配硫酸铝混凝性能及絮体特性

在研究氢氧化镁混凝特性的基础上,复配氯化镁和硫酸铝作为混凝剂,以高岭土配水水样为研究对象,运用iPDA在线监测技术对混凝过程絮体形成进行监测,探讨了单独使用氯化镁和硫酸铝以及二者复配使用的混凝效果和絮体特性,确定复配使用的各种条件。结果表明,对于浊度20 NTU,pH 11.5的高岭土配水水样,氯化镁、硫酸铝最佳投加量分别为7.2 mg/L(Mg2+计)和3 mg/L(Al3+计);硫酸铝跟氯化镁复配使用时,先投加硫酸铝,间隔30 s后投加氯化镁,混凝效果较好;在镁离子最佳投加量7.2 mg/L时,铝和镁最佳质量比在1∶3~1∶2之间;镁铝复配时其FI值明显大于单独作用时,即絮体尺寸大小:二者复配硫酸铝氯化镁,而且复配条件下Zeta电位值在零电势左右浮动,浮动范围小,更利于聚集沉淀;镁铝复配时发生了协同效应,弥补了单独使用氯化镁混凝过程的不足。     

Degradation of the potential rodent contraceptive quinestrol and elimination of its estrogenic activity in soil and water

Quinestrol has shown potential for use in the fertility control of the plateau pika population of the Qinghai–Tibet Plateau. However, the environmental safety and fate of this compound are still obscure. Our study investigated degradation of quinestrol in a local soil and aquatic system for the first time. The results indicate that the degradation of quinestrol follows first-order kinetics in both soil and water, with a dissipation half-life of approximately 16.0 days in local soil. Microbial activity heavily influenced the degradation of quinestrol, with 41.2 % removal in non-sterile soil comparing to 4.8 % removal in sterile soil after incubation of 10 days. The half-lives in neutral water (pH 7.4) were 0.75 h when exposed to UV light (λ?=?365 nm) whereas they became 2.63 h when exposed to visible light (λ?>?400 nm). Acidic conditions facilitated quinestrol degradation in water with shorter half-lives of 1.04 and 1.47 h in pH 4.0 and pH 5.0 solutions, respectively. Moreover, both the soil and water treatment systems efficiently eliminated the estrogenic activity of quinestrol. Results presented herein clarify the complete degradation of quinestrol in a relatively short time. The ecological and environmental safety of this compound needs further investigation.     

碳酸根对磷酸钙沉淀反应回收磷的影响简

以模拟的厌氧消化液为处理对象,通过小试实验,考察不同初始磷浓度C_P、Ca/P物质的量比、pH和温度下,碳酸根（CO₃^2-）对磷酸钙沉淀反应回收磷的影响;利用扫描电镜（SEM）、X射线衍射仪（XRD）和傅里叶变换红外光谱（FTIR）对沉淀产物进行表征。结果表明,高浓度的CO₃^2-对以磷酸钙沉淀反应去除和回收磷的效率影响较大;C_P相同时,CO₃^2-浓度（C_CO3^2-）越大,P的去除率越低,低C_P（20 mg/L）时尤为显著;当C_CO3^2-相同时,随着C_P的增大,反应速率加快,P的去除率逐渐升高,但升高幅度越来越小;增大Ca/P比和pH能提高P的去除率,降低CO₃^2-对磷酸钙沉淀反应的抑制作用,综合考虑实际效果,应选择Ca/P比为3.33,pH为9.0作为适宜的反应条件;升高温度对降低CO₃^2-对磷酸钙沉淀反应的抑制作用贡献不大。在C_P为60 mg/L,Ca/P比为1.67,pH为9.0,温度为20℃的条件下,当C _CO3^2-为0时,得到的沉淀产物主要为羟基磷灰石HAP;当C _CO3^2-为30 mmol/L时,得到的沉淀产物为磷酸钙和碳酸合磷灰石的混合物。     

一株光合细菌的分离鉴定及其产电特性

采用光照富集及厌氧划线法从污水厂二沉池活性污泥分离到一株光合细菌YC-1,结合菌落特征、细胞形态、活细胞吸收光谱及16S rRNA基因序列分析等对其进行了分类学鉴定,并研究了YC-1在不同光源照射下的产电性能。结果表明,该菌为短杆状,有鞭毛,菌落呈淡粉色,含有大量细菌叶绿素a,16S rRNA基因序列与Rhodopseudomonas palustris DX-1相似度为99%,属于假单胞菌属(Pseudomonas sp.);双室微生物燃料电池的阳极室接种YC-1,并以乙酸钠为底物,铁氰化钾作为阴极电子受体,外载为1 000Ω时,电池稳定运行时输出电压为0.58 V,且输出电压不受光源光谱影响。     

锰铜铈氧化物催化剂氧化NO性能及动力学研究

实验以TiO2为载体采用浸渍法制备CuOx/TiO2、CeOx/TiO2、CuCeOx/TiO2和MnCuCeOx/TiO2催化剂,考察这些催化剂氧化NO活性,探究Cu、Ce摩尔比和添加Mn元素对CuCeOx/TiO2催化剂氧化NO活性的影响,使用扫描电镜观察催化剂表面结构。研究发现,Cu、Ce元素配合后的CuCeOx/TiO2催化剂氧化活性明显好于单独含Cu、Ce的催化剂,当Cu、Ce摩尔比为Cu:Ce=1∶2时,CuCeOx/TiO2催化剂氧化活性最好,在NO浓度500×10-6,O210%,空速为24 000 h-1,350℃时,NO氧化度为0.62;添加Mn元素可以提高CuCeOx/TiO2催化剂低温氧化活性,250℃时,MnCuCe/Ti-3和MnCuCe/Ti-5催化剂氧化度为0.53和0.69,300℃时,MnCuCe/Ti-3和MnCuCe/Ti-5催化剂氧化度均为0.76;此外,实验还研究了NO在MnCuCe/Ti-3催化剂上反应的动力学方程。     

丝状菌污泥膨胀及其致密过程中菌丝体演替规律

为了探索丝状菌的致密途径、解决丝状菌污泥膨胀的难题,从丝状菌的自身特点及外部条件出发研究了其在污泥膨胀及致密过程中菌丝体的演替规律。研究发现,致密生长的大絮体对丝状菌的种类是有选择性的,那些丝体较弯曲、丝体强度较大、贮存能力强的菌丝体更利于形成聚集态生长。另外,研究表明,不同种类丝状菌的生长势和存贮能力不同,对底物的利用上亦存在着竞争关系。实验中存在的几个菌种对PHB颗粒的存贮能力由高到低依次为:Nostocoida limicolaⅡ、Type 1851、Type 0701、Type 021N型菌体。     

臭氧联用技术深度处理腈纶废水的效果对比

将臭氧分别与超声波、H2O2、紫外光等联用,深度处理干法腈纶生产厂生化池出水,对各种联用技术的处理效果进行了研究。实验结果表明：在进水流量2 L/min、反应时间30 min、臭氧加入量3.5 g/（L?h）的条件下,当超声功率为300 W时,臭氧-超声联用技术的COD去除率为30.0%;当H2O2加入量为0.4 mL/L时,臭氧-H2O2联用技术的COD去除率为50.7%;当紫外灯功率为40 W时,臭氧-紫外光联用技术的COD去除率为49.9%;在各种联用技术中,臭氧-H2O2联用技术的运行成本最低（为7.5 元/t）,且处理后出水COD为143 mg/L,达到《<污水综合排放标准>（GB8978—1996）中石化工业COD标准值修改单》中的一级排放标准。综合考虑,臭氧-H2O2联用技术是深度处理干法腈纶废水的最优工艺。     

Mn/γ-Al2O3催化剂的制备及头孢合成废水的催化臭氧氧化法深度处理

对Mn/γ-Al₂O₃催化剂的制备条件及头孢合成废水的催化臭氧氧化法深度处理工艺条件进行了优化。实验结果表明：以Mn（NO₃）₂溶液为浸渍液,Mn/γ-Al₂O₃催化剂的最优制备条件为浸渍液浓度0.10 mol/L、浸渍时间9 h、焙烧温度400 ℃、焙烧时间2 h;在反应时间为30 min、废水pH为9.0、臭氧通量为4.6 mg/min、催化剂加入量为5 g/L的条件下,当进水COD、BOD₅、ρ（氨氮）和色度分别为220~250 mg/L,8~10 mg/L,10~12 mg/L和60~70倍时,出水COD、BOD₅、ρ（氨氮）和色度的平均去除率分别为53%,30%,33%和93%,出水水质满足GB 21904—2008《化学合成类制药工业水污染物排放标准》的要求。     

Catalytic hydrolysis of urea from wastewater using different aluminas by a fixed bed reactor

In order to find an effective method for treating urea wastewater, the experiments on the hydrolysis of urea in wastewater were conducted in a fixed bed reactor with different aluminas (α-Al₂O₃, γ-Al₂O₃, and η-Al₂O₃) as catalysts respectively in contrast with inert ceramic particle. The results indicate that the three alumina catalysts show obvious catalytic activity for urea hydrolysis at 125 °C. The order of activity is η-Al₂O₃?>?γ-Al₂O₃?>?α-Al₂O₃, and the activity difference increases with increasing temperature. According to the characterization results, surface acidity has little impact on the activity of catalyst. However, it was found that surface basicity of alumina catalyst plays an important role in catalytic hydrolysis of urea, and the activity of catalyst may be also influenced by the basic strength. With η-Al₂O₃ as catalyst, the urea concentration in wastewater is reduced to 4.96 mg/L at a temperature of 165 °C. Moreover, the η-Al₂O₃ shows a good stability for urea hydrolysis. The hydrolysis of urea over η-Al₂O₃ catalyst can evidently reduce the reaction temperature and is promising to replace industrial thermal hydrolysis process.