控轧控冷型Q550高强钢高温后的力学性能试验研究∗

通过升温、降温及冷却后的常温静力拉伸试验,对控轧控冷型(TMCP)Q550高强钢高温后的力学性能展开试验研究,得到了经历200～900℃之间9个不同的过火温度及自然冷却与浸水冷却两种冷却方式后,钢材的表观特征、应力-应变关系与基本力学性能参数,包括弹性模量、屈服强度、抗拉强度及断后伸长率。结果表明,过火温度及冷却方式对TMCP型Q550钢材弹性模量的影响较小;过火温度超过600℃时,钢材高温后的屈服强度和抗拉强度开始折减;过火温度达到700℃后,钢材的应力-应变曲线皆无屈服平台,不同冷却方式的结果开始呈现差异:随过火温度升高,自然冷却后钢材的强度减小而断后伸长率增大,浸水冷却则相反,且二者差异愈加明显。将试验结果与文献结果对比,发现当过火温度超过700℃时,TMCP型Q550高强钢高温后的力学性能与调质型(QT)Q550高强钢存在差异,在经历较高的过火温度后,TMCP钢在自然冷却下的强度折减比QT钢严重,浸水冷却下的强度增长程度低于QT钢。     

生物法处理棉浆黑液的现场实验研究

利用经驯化的以嗜碱菌群为主的好氧活性污泥及常规厌氧、好氧污泥,针对不同浓度的棉浆黑液在现场进行了单独"好氧"及"好氧-厌氧-好氧"全流程工艺实验。结果表明:对棉浆黑液直接进行好氧曝气,可将原水pH值自12.4左右稳定降低至10以下,COD去除率可达40%左右。全流程实验中厌氧效果显著,pH值最低可降至8.2,整个系统抗冲击能力强,运行稳定,COD总去除率保持在63%以上。     

气浮法对矿区洗浴污水中洗涤剂处理及回用研究

通过不同方案的对比试验,确定了矿区洗浴污水处理及回用的工艺,重点解决了阴离子合成洗涤剂对水质的影响,为矿区洗浴污水回用提供一项可行的方案。     

稻草型生物有机肥对萝卜的作用效果

为推广应用稻草型生物有机肥,采用田间小区试验研究了稻草型生物有机肥对萝卜(Raphanus sativus)功能叶叶绿素含量、碳氮代谢关键酶活性、萝卜产量和品质的影响.结果表明:稻草型生物有机肥处理Ⅰ与等NPK养分施用量的纯化肥处理Ⅱ和菜枯肥处理Ⅲ相比,可提高萝卜功能叶叶绿素含量、防止功能叶早衰;提高硝酸还原酶、蔗糖合成酶、蔗糖磷酸合成酶三种碳氮代谢关键酶活性.处理Ⅰ使萝卜的产量分别比处理Ⅱ和处理Ⅲ提高4.48%、6.01%,维生素C分别提高22.48%、28.24%,可溶性糖含量分别提高10.39%、19.91%,萝卜硝酸盐含量分别下降8.78%和16.67%,且以上4个指标处理Ⅰ与处理Ⅱ和处理Ⅲ的差异均达极显著水平,此外亚硝酸盐含量也明显降低.     

Life cycle assessment of TV sets in China: A case study of the impacts of CRT monitors

Along with the rapid increase in both production and use of TV sets in China, there is an increasing awareness of the environmental impacts related to the accelerating mass production, electricity use, and waste management of these sets. This paper aims to describe the application of life cycle assessment (LCA) to investigate the environmental performance of Chinese TV sets. An assessment of the TV set device (focusing on the Cathode Ray Tube (CRT) monitor) was carried out using a detailed modular LCA based on the international standards of the ISO 14040 series. The LCA was constructed using SimaPro software version 7.2 and expressed with the Eco-indicator' 99 life cycle impact assessment method. For a sensitivity analysis of the overall LCA results, the CML method was used in order to estimate the influence of the choice of the assessment method on the results. Life cycle inventory information was compiled by Ecoinvent 2.2 databases, combined with literature and field investigations on the current Chinese situation. The established LCA study shows that the use stage of such devices has the highest environmental impact, followed by the manufacturing stage. In the manufacturing stage, the CRT and the Printed Circuit Board (PCB) are those components contributing the most environmental impacts. During the use phase, the environmental impacts are due entirely to the methods of electricity generation used to run them, since no other aspects were taken into account for this phase. The final processing step-the end-of-life stage-can lead to a clear environmental benefit when the TV sets are processed through the formal dismantling enterprises in China.     

有机磷阻燃剂生产废水预处理工艺研究

采用液膜萃取—酸析沉降—络合萃取组合工艺对有机磷阻燃剂生产废水进行预处理.最佳工艺条件为:液膜萃取时,液膜油相(表面活性剂与煤油的混合液)与内水相(H2SO4溶液)的体积比2∶1、乳化液膜与废水的体积比1∶8、废水pH 13.0,硫酸体积分数10％、煤油中表面活性剂质量浓度30 g/L、液膜萃取时间 15 min;酸析沉降时,废水pH l.0,酸析沉降时间30 min;络合萃取时,络合萃取剂(烷基叔胺N235与煤油的混合液)中烷基叔胺N235体积分数30％,络合萃取剂与废水的体积比1∶4,废水pH l.0,络合萃取时间30 min.在此最佳处理条件下,废水COD总去除率可达93％,吡啶去除率达99.9％以上,总磷去除率可达97％,BOD5/COD提高至0.32,有利于后续生化处理.     

钛基IrO2-RuO2阳极电解处理亚甲基蓝溶液

采用钛基IrO2-RuO2为阳极材料,不锈钢为阴极材料,NaCl质量浓度为10 g/L的溶液为电解液,对亚甲基蓝溶液进行电化学处理。实验结果表明:处理初始质量浓度为25 mg/L的亚甲基蓝溶液,电解电流0.050 A,电解20 min后亚甲基蓝去除率达95%;处理初始质量浓度为100 mg/L的亚甲基蓝溶液,电解电流0.100 A,电解30 min后亚甲基蓝去除率达98%。随着电解时间和电解电流的增加,亚甲基蓝去除率均增大。     

大孔树脂吸附—Fenton试剂氧化法预处理含邻苯二甲酸二异丁酯废水

采用大孔树脂吸附—Fenton试剂氧化法预处理含邻苯二甲酸二异丁酯(DIBP)废水。大孔树脂吸附工段的最佳实验条件为:以树脂NDA88为吸附剂,废水pH为2。NDA88经过10批次的连续使用,COD去除率基本稳定在58%左右,脱附率可达96%以上,吸附后废水COD为12 000 mg/L左右。Fenton试剂氧化工段的最佳实验条件为:H2O2加入量70 mL/L,n(H2O2):n(Fe2+)=4,废水pH 4。在此最佳条件下进行实验,Fenton试剂氧化工段COD去除率达65%,处理后废水COD为4 200 mg/L。     

纳滤膜处理含锰废水

采用纳滤膜处理电解锰生产过程中产生的含锰废水,考察了操作压力、阻垢剂和反冲洗等因素对膜通量和各金属离子截留率的影响。实验结果表明:操作压力越大,膜通量越大,且膜通量随运行时间延长下降得越快;在操作压力为2.0 MPa的条件下,纳滤膜对Mg2+的截留率为90.69%,对Mn2+的截留率为89.72%,对Ca2+的截留率最高,达100%;加入阻垢剂后,纳滤膜的膜通量比未加入阻垢剂时的膜通量略大;反冲洗4次后,膜通量均可完全恢复。     

Carbonaceous species in fine particles at the background sites in Korea between 1994 and 1999

Organic carbon (OC) and elemental carbon (EC) in fine particles (PM_2.5) at two background sites, Kosan and Kangwha in Korea were measured during intensive field studies between 1994 and 1999. Fine particles were collected on pre-fired quartz filters in a low-volume sampler and analyzed using the selective thermal oxidation method with MnO₂ catalyst. The OC and EC concentrations at Kosan located at western tip of Cheju Island in southern Korea are lower than those at Kangwha located at western coastal area in mid-Korean peninsula. Still, the OC concentrations at Kosan are generally higher than those at other background areas in Japan and USA. The EC concentrations at Kosan are lower than or comparable to those at other background areas. The total carbon (TC, sum of OC and EC) to EC ratio values at both sites were higher than those at other background areas in Japan and USA. At Kosan, the OC and EC concentrations when air parcels were from southern China were higher than those when air parcels were coming from northern China. However, at Kangwha, the differences were statistically not clear since most air parcels were from northern China. Except when air parcels were from the North Pacific during summer, the OC and EC concentrations are well correlated indicating that both OC and EC share the same emission/transport characteristics. From the gaseous hydrocarbon data and the OC and EC relationship, it was found that during summer local biogenic emissions of OC might be significant at Kosan.