Wastewater treatment with multilayer media of waste and natural indigenous materials

Wastewater treatment using waste materials (refuse concrete, waste paper and charcoal) and natural indigenous rocks (andesite, limestone, granite and nitrolite) in the form of multilayer media was investigated. The removal of suspended solids (SS), phosphate ion, nitrate ion, ammonium ion, toxic metals and chemical oxygen demand (COD) were evaluated for the multilayer wastewater treatment system. Effective removal of heavy metals such as cadmium, chromium, mercury and lead was demonstrated. SS and phosphate ion were removed with relatively high efficiency and the COD after treatment was lessened using certain combinations of media. The present wastewater treatment system is simple, convenient and low cost. Therefore, this method can be applied in small scale plants for wastewater treatment in local and nonexclusive areas.     

Removal of hexavalent chromium upon interaction with biochar under acidic conditions: mechanistic insights and application

Environmental Science and Pollution Research - Chromium pollution of soil and water is a serious environmental concern due to potential carcinogenicity of hexavalent chromium [Cr(VI)] when...     

Black carbon aerosols in urban air in South Asia

We report data from a yearlong (2006–2007) study of black carbon concentrations ([BC]) measured at 5-min intervals with an Aethalometer in Karachi, Pakistan. Daily mean [BC] varied from about 1 to 15 μg m^?3. However, short-term spikes exceeding 40 μg m^?3 were common, occurring primarily during the morning and evening rush-hour periods. The [BC] values were highest during November through February, ～10 μg m^?3, and lowest during June through September, ～2 μg m^?3. Diurnal, seasonal, and day-of-the-week trends are discussed. It is demonstrated that these trends are strongly affected by meteorological patterns. A simple expression is applied to the concentration profiles to separate the effects of meteorological conditions and elucidate the underlying emissions patterns. Daily emissions varied from 14,000 to 22,000 kg of BC per day. When integrated over the year emissions for Karachi Proper were estimated at 6.7 kilometric tons per year and emissions for greater Karachi were 17.5 kilometric tons per year. Folding in the populations of each area yields BC emissions of 0.74 and 1.1 kg per person per year, respectively. Applying the model to previously collected data at Lahore, Pakistan yields emissions during November–January that are around a factor of two higher than those in Karachi, but because the BC measurements in Lahore covered only three months, no estimates of annual emissions were attempted. Given the large populations of these cities the local health impact from PM alone is expected to be severe but because of the high [BC] emissions the impact on the global climate may be equally significant.     

Recycling polymeric waste from electronic and automotive sectors into value added products

The environmentally sustainable disposal and recycling of ever increasing volumes of electronic waste has become a global waste management issue. The addition of up to 25% polymeric waste PCBs (printed circuit boards) as fillers in polypropylene (PP) composites was partially successful: while the tensile modulus, flexural strength and flexural modulus of composites were enhanced, the tensile and impact strengths were found to decrease. As a lowering of impact strength can significantly limit the application of PP based composites, it is necessary to incorporate impact modifying polymers such as rubbery particles in the mix. We report on a novel investigation on the simultaneous utilization of electronic and automotive rubber waste as fillers in PP composites. These composites were prepared by using 25 wt.% polymeric PCB powder, up to 9% of ethylene propylene rubber (EPR), and PP: balance. The influence of EPR on the structural, thermal, mechanical and rheological properties of PP/PCB/ EPR composites was investigated. While the addition of EPR caused the nucleation of the β crystalline phase of PP, the onset temperature for thermal degradation was found to decrease by 8%. The tensile modulus and strength decreased by 16% and 19%, respectively; and the elongation at break increased by ~71%. The impact strength showed a maximum increase of ~18% at 7 wt.%–9 wt.% EPR content. Various rheological properties were found to be well within the range of processing limits. This novel eco-friendly approach could help utilize significant amounts of polymeric electronic and automotive waste for fabricating valuable polymer composites.

Open image in new window

     

Cadmium contamination in agricultural soils of Bangladesh and management by application of organic amendments: evaluation of field assessment and pot experiments

Environmental Geochemistry and Health - In recent years, cadmium (Cd) contamination in agricultural soils and its subsequent transfer to crops is one of the high-priority environmental and public...     

Determination of cadmium in water and herbal medicine by Penicillium chrysogenum immobilized on silica gel for flame atomic absorption spectroscopy

Penicillium chrysogenum was immobilized on silica to develop a simple and cost effective method for solid phase extraction of Cd(II) and determination using flame atomic absorption spectrometry (FAAS). The sorbent was characterized by Fourier transform infrared spectroscopy and packed into a column. The conditions for quantitative sorption and desorption of Cd(II) were optimized. The preconcentration factor was 100 while detection limit was 0.61 µg L^?1 with a relative standard deviation of 1.0%. The method was applied for determination of Cd in herbal medicine and tap water.     

Variations in physico-chemical and microbiological characteristics of water during breeding of Cyprinus carpio in a closed hatchery system

Physico-chemical and microbial characteristics of culture water were examined during the induced breeding of Cyprinus carpio in a controlled environmental system. Water temperature, dissolved oxygen, nitrate, phosphate, pH, ammonia nitrogen, total bacterial count, hardness, salinity, carbonate and bicarbonate were estimated before and after spawning and hatching. Average alteration in water pH before and after spawning was 7.91-7.57 and 7.86-7.58 respectively. Total hardness, carbonate and bicarbonate showed insignificant variations. Nitrate, ammonia nitrogen and phosphate contents significantly increased after spawning and hatching p < 0.05. The average increase in nitrate was from 2.94 to 8.62 microg l(-1) after spawning and 3.10 to 8.49 microgl(-1) after hatching. Ammonia nitrogen contents were sharply increased from an average of 0.011 to 1.87 mg l(-1) after spawning and 0.013 to 0.56 mg l(-1) after hatching. The average phosphates increased from 2.59 to 4.15 microg l(-1) after spawning and 2.61 to 4.03 microg l(-1) after hatching. Dissolved oxygen was sharply depleted even after a continuous aeration. Temperature played a vital role during breeding. No successful breeding was observed at a temperature of 17 degrees C or below and 31 degrees C or above. There is a significant association between temperature, spawning and hatching (p < 0.05). By optimizing temperature, the breeding success of this carp was achieved with a statistical significance of p < 0.05. Total bacterial count was significantly increased after spawning and hatching. It was related to the amount of discharge and may cause mass mortality of fish embryo and spawn in a closed hatchery system.     

Prevalence of heavy metal resistance in bacteria isolated from tannery effluents and affected soil

In the present study, a total of 198 bacteria were isolated, 88 from the tannery effluents and 110 from agricultural soil irrigated with the tannery effluents. Tannery effluents and soils were analyzed for metal concentrations by atomic absorption spectrophotometer. The tannery effluents and soil samples were found to be contaminated with chromium, nickel, zinc, copper, and cadmium. All isolates were tested for their resistance against Cr^6?+?, Cr^3?+?, Ni^2?+?, Zn^2?+?, Cu^2?+?, Cd^2?+?, and Hg^2?+?. From the total of 198 isolates, maximum bacterial isolates were found to be resistant to Cr^6?+? 178 (89.9%) followed by Cr^3?+? 146 (73.7%), Cd^2?+? 86 (43.4%), Zn^2?+? 83 (41.9%), Ni^2?+? 61 (30.8%), and Cu^2?+? 51 (25.6%). However, most of the isolates were sensitive to Hg^2?+?. Among the isolates from tannery effluents, 97.8% were resistant to Cr^6?+? and 64.8% were resistant to Cr^3?+?. Most of the soil isolates were resistant against Cr^6?+? (83.6%) and Cr^3?+? (81.8%). All isolates were categorized into Gram-positive and Gram-negative bacteria. In a total of 114 Gram-positive isolates, 91.2% were resistant to Cr^6?+? followed by 73.7% to Cr^3?+?, 42.1% to Zn^2?+?, 40.4% to Cd^2?+?, and 32.5% to Ni^2?+?. Among Gram-negative isolates, 88.1% were found showing resistance to Cr^6?+?, 75.0% to Cr^3?+?, and 47.6% were resistant to Cd^2?+?. Majority of these metal-resistant isolates were surprisingly found sensitive to the ten commonly used antibiotics. Out of 198 isolates, 114 were found sensitive to all antibiotics whereas only two isolates were resistant to maximum eight antibiotics at a time. Forty-one and 40 isolates which constitute 20.7% and 20.2% were resistant to methicilin and amoxicillin, respectively.     

A linear and nonlinear approach for interpretation of groundwater quality based on water quality index

In this study using linear and nonlinear approach, aggregate indices for various water quality parameters were analyzed. Using a linear and nonlinear interpolating surface, various water quality variables at grid points were investigated that is essential for mapping. The values help in constituting a key approach for determining the water quality index (WQI), which converts pollutant concentration data into subindex values and then combines them into a single score. One of the biggest advantages of WQI is its summary and intuitive communication capability which will be extremely helpful for demarcating safe aquifer zones of groundwater and in the selection of suitable method for remedial. The present study also describes pollution potential in ground water of Madhya Pradesh, India. The aggregate indices suggest intermediate to high pollution susceptibility in some region of Madhya Pradesh that may increase further if not managed. The overall interpretation of the study will be helpful in formulating suitable approach for water quality interpretation and sustainable planning of groundwater resources.     

Understanding the impact of waste disposal sites on soil quality for agricultural production: A case study of the Kiteezi landfill,Uganda

Leachate from waste disposal sites (WDS) can significantly affect the soil physical, chemical and biological qualities, reducing soil health and agricultural productivity. However, there is a paucity of data on soil quality for understanding soil health impact due to WDS in Uganda. This study's aim was to understand, using the Kiteezi landfill site, how WDS impact soil properties. Soil samples were collected over 4 months in and around the landfill from three locations, and the soil quality data of the nearby area were used as baseline data for assessing the impact on soil due to WDS in the area. There were significant increases in the concentration of all studied parameters at the landfill except total N. The concentrations of ammonium (14.84 ± 1.76 mg/kg), nitrate (127.96 ± 18.36 mg/kg), and pH (7.8) were above the optimum levels. The levels of available P (181.4 ± 28.9 mg/kg) and exchangeable bases; K (2.23 ± 0.24 mg/kg), Na (1.17 ± 0.14 mg/kg), Mg (3.35 ± 0.3 mg/kg) and Ca (14 ± 1.1 mg/kg) cmol (+)/kg were optimal for plant growth. The calculated CEC of 20.75 cmol (+)/kg) showed that soils have a good potential to supply plant nutrients. Heavy metal levels were still below the permissible limit. Hence, the study shows that although WDS may contribute to the increase of soil fertility, they can potentially reduce the overall productivity of soil by increasing nutrient levels beyond optimum levels.