Estimating contaminant mass discharge: a field comparison of the multilevel point measurement and the integral pumping investigation approaches and their uncertainties

In this field study, two approaches to assess contaminant mass discharge were compared: the sampling of multilevel wells (MLS) and the integral groundwater investigation (or integral pumping test, IPT) that makes use of the concentration-time series obtained from pumping wells. The MLS approached used concentrations, hydraulic conductivity and gradient rather than direct chemical flux measurements, while the IPT made use of a simplified analytical inversion. The two approaches were applied at a control plane located approximately 40m downgradient of a gasoline source at Canadian Forces Base Borden, Ontario, Canada. The methods yielded similar estimates of the mass discharging across the control plane. The sources of uncertainties in the mass discharge in each approach were evaluated, including the uncertainties inherent in the underlying assumptions and procedures. The maximum uncertainty of the MLS method was about 67%, and about 28% for the IPT method in this specific field situation. For the MLS method, the largest relative uncertainty (62%) was attributed to the limited sampling density (0.63 points/m(2)), through a novel comparison with a denser sampling grid nearby. A five-fold increase of the sampling grid density would have been required to reduce the overall relative uncertainty for the MLS method to about the same level as that for the IPT method. Uncertainty in the complete coverage of the control plane provided the largest relative uncertainty (37%) in the IPT method. While MLS or IPT methods to assess contaminant mass discharge are attractive assessment tools, the large relative uncertainty in either method found for this reasonable well monitored and simple aquifer suggests that results in more complex plumes in more heterogeneous aquifers should be viewed with caution.     

Assessing the recovery potential of alpine moss-sedge heath: reciprocal transplants along a nitrogen deposition gradient

The potential of alpine moss-sedge heath to recover from elevated nitrogen (N) deposition was assessed by transplanting Racomitrium lanuginosum shoots and vegetation turfs between 10 elevated N deposition sites (8.2-32.9 kg ha⁻¹ yr⁻¹) and a low N deposition site, Ben Wyvis (7.2 kg ha⁻¹ yr⁻¹). After two years, tissue N of Racomitrium shoots transplanted from higher N sites to Ben Wyvis only partially equilibrated to reduced N deposition whereas reciprocal transplants almost matched the tissue N of indigenous moss. Unexpectedly, moss shoot growth was stimulated at higher N deposition sites. However, moss depth and biomass increased in turfs transplanted to Ben Wyvis, apparently due to slower shoot turnover (suggested to result partly from decreased tissue C:N slowing decomposition), whilst abundance of vascular species declined. Racomitrium heath has the potential to recover from the impacts of N deposition; however, this is constrained by the persistence of enhanced moss tissue N contents.     

Development of a livestock odor dispersion model: part I. Model theory and development

A livestock odor dispersion model (LODM) was developed to predict mean odor concentration, odor frequency, instantaneous odor concentration, and peak odor concentration from livestock operations. This model is based on the Gaussian fluctuating plume model and has the ability to consider the instantaneous concentration fluctuations and the differences between odor and traditional air pollutants. It can predict odor frequency from the routine hourly meteorological data input and deal with different types of sources and multiple sources. Also, the relationship between odor intensity and odor concentration was incorporated into the model.     

Printed wiring boards for mobile phones: characterization and recycling of copper

The popularization of mobile phones, combined with a technological evolution, means a large number of scrap and obsolete equipment are discarded every year, thereby causing economic losses and environmental pollution. In the present study, the printed wiring boards scrap of mobile phones were characterized in order to recycle some of the device components, using techniques of mechanical processing, hydrometallurgy and electrometallurgy. The use of the techniques of mechanical processing (milling, particle size classification, magnetic and electrostatic separation) was an efficient alternative to obtain a concentrated fraction (mainly iron in the magnetic fraction and copper in the conductive fraction) and another fraction containing polymers and ceramics. At the end of mechanical processing, a concentrated fraction of metals could be obtained with an average concentration of 60% copper. This concentrated fraction in metals was dissolved in aqua regia and sent to electrowinning to recover 92% of the dissolved copper. The obtained cathodes have a copper content above 95%, which demonstrates the technical feasibility of recovery of copper using the techniques of mechanical processing, hydrometallurgy and electrometallurgy.     

Solid waste management practices in Turkey

As an economically developing country, Turkey has very well operated integrated solid waste management applications structured on modern facilities, besides over 2,000 scattered open dump areas in the country. Integrated waste management applications seem eligible for the metropolitan cities like Istanbul and Izmit (Kocaeli). Attempts have not been encouraging for the scattered regional settlements using central storage sites due to financial shortages and received rejections from nearby settlements. Small-scale compact solid waste management systems with materials recycling and composting can be more suitable alternatives in the small-scale regional settlements. The major constituents of municipal solid waste are organic in nature and approximately a quarter of municipal solid waste is recyclable. Although paper, including cardboard, is the main constituent, the composition of recyclable waste varies strongly by the source or the type of collection point. Solid wastes need primary treatment in order to be suitable for incineration and composting. Turkey needs to give more emphasis on the usage of modern solid waste removal technologies to overcome the overgrowing solid waste disposal problems.     

A study on legislative and policy tools for promoting the circular economic model for waste management in China

The circular economy has been developing rapidly in recent years in China. A legislative system has been created to provide legal protection for the development of a circular economy, including a series of price and tax measures in the waste management area. These measures form the basic foundation for promoting better waste management under the circular economic model. Many challenges, however, remain. For instance, the legal system needs to incorporate more sophisticated science, and China lacks key waste treatment technology that could support the further development of a circular economy. There is also a need to educate the public about the concept of the circular economy and its benefits. Specific suggestions are made for the development and implementation of the circular economic model.     

Biohydrogen using leachate from an industrial waste landfill as inoculum

Since hydrogen is a renewable energy source, biohydrogen has been researched in recent years. However, data on hydrogen fermentation by a leachate from a waste landfill as inoculum are scarce. We investigated hydrogen production using a leachate from an industrial waste landfill in Kanagawa Prefecture. The results showed no methane gas production, and the leachate was a suitable inoculum for hydrogen fermentation. The maximum H₂ yield was 2.67 mol of H₂ per mol of carbohydrate added, obtained at 30°C and an initial pH of 7. The acetate and butyrate production was significant when the H₂ yield was higher. Oxidation–reduction potential analysis of the culture suggested that hydrogen-producing bacteria in the leachate were facultative anaerobic. Scanning electron microscope observations revealed that the hydrogen-producing bacteria comprised bacilli about 2 μm in length.     

Decomposition of dichloromethane and in situ alkali absorption of resulting halogenated products by a packed-bed non-thermal plasma reactor

For an effective decomposition and removal of organic halogenated compounds, a packed-bed non-thermal plasma reactor with in situ absorption of the resulting halogenated products by alkaline sorbent incorporated was proposed. In the plasma reactor, α-Al₂O₃ particles of 1 and 3 mm (mean particle diameter) were packed as solid dielectric medium to enhance the plasma power density in the reactor. Further, alkaline sorbent of Ca(OH)₂ was doped onto the surface of α-Al₂O₃ particles, in order to remove halogenated products by in situ absorption with Ca(OH)₂. A high-voltage and high-frequency pulsed power of −15 to 15 kV and 1 kHz was applied to the wire electrode of the plasma reactor by means of a DC power source. In the present study, as the sample of an organic halogenated compound that is most popularly used, we selected dichloromethane (CH₂Cl₂), and 500 ppm of the initial concentration of CH₂Cl₂ was fed into the reactor accompanied by air at a fixed flow rate of 500 × 10⁻⁶ m³ min⁻¹ at room temperature. As a result, it was recognized that the amount of CH₂Cl₂ decomposed by non-thermal plasma in an α-Al₂O₃ particle bed increased with an increase in plasma input power. The ratio of decomposition of CH₂Cl₂ was almost 100% at 13 kV of electric power and 1 kHz frequency, and CO₂, CH₃Cl, COCl₂, HCl, and Cl₂ were observed as the major reaction products. On the other hand, when CH₂Cl₂ was introduced into the plasma reactor where α-Al₂O₃ particles doped with Ca(OH)₂ were packed, the ratio of decomposition of CH₂Cl₂ became higher, compared to the case that α-Al₂O₃ particles were not doped with Ca(OH)₂. Moreover, there were no halogenated by-product gases detected in the outlet gas from the reactor. As the solid reaction products, CaClOH and Ca(ClO)₂·4H₂O were detected on Ca(OH)₂ by X-ray diffraction. From these findings, it was recognized that CH₂Cl₂ was decomposed more effectively without producing unwanted harmful halogenated by-products in the proposed non-thermal plasma reactor where α-Al₂O₃ particles doped with Ca(OH)₂ sorbent were packed.     

Waste incineration,PVC, and dioxins

Waste incineration is becoming increasingly necessary to tackle the rapidly rising amounts of municipal solid waste (MSW); in China many large cities are already surrounded by a girdle of landfills. Still, the not-in-my-backyard (nimby) syndrome holds strong. This attitude stems from fear of dioxins. These have been associated with incineration (‘dioxin factories’) and at times also with polyvinylchloride. In this paper this issue is analysed. China should build additional trust in MSW incineration, following promulgation of stricter emission standards, enforced by stringent controls.     

The effect of the addition of fly ash to municipal digested sludge on its electroosmotic dewatering

Effective handling of municipal digested sludge requires that the product cake have low water content. To this end, we investigated the change in sludge dewaterability after the addition of fly ash to municipal digested sludge, dewatering of which is difficult because of its high organic content. The performance of the dewatering is compared with that of electroosmotic dewatering (EDW) and conventional mechanical dewatering (CMD). Fly ash classified by sieving to the size of 25–75 μm and >75 μm is added to the municipal digested sludge by 10, 20, and 50 wt% by wet base. When adding fly ash particles to municipal digested sludge, dewatering efficiency improved with smaller fly ash particle size and with increase in the amount. When sludge was dewatered using an electroosmotic dewatering method, the dewatering efficiency is improved about 40% by adding fly ash of 25–75 μm particle size with 20 wt% when compared with conventional mechanical dewatering method without adding the fly ash. It is concluded that fly ash particles rich in inorganic material are helpful in the dewatering process when added to municipal digested sludge and EDW is more effective than CDW.