Monitoring and assessing variation of sewage quality and microbial functional groups in a trunk sewer line

In this study, the variation of sewage quality was investigated and the active fraction of different microbial functional groups in biofilm was quantified in a 5.6-km trunk sewer line. The sewage quality including suspended solids, biochemical oxygen demand, total chemical oxygen demand (COD), total nitrogen, total Kjeldahl nitrogen, ammonia nitrogen, nitrite nitrogen, and nitrate nitrogen were measured and compared with the values in literatures. The results indicated that since the wastewater treatment plant was not operated at its full capacity, the concentrations of different compounds were lower compared with the values in literatures. The values of heterotrophic growth rate constant lay between 5.6 and 8.6 day^???1. Its average value was 7.7 day^???1. The values of heterotrophic lysis rate constant lay between 0.2 and 0.4 day^???1. The active heterotrophic biomass in biofilm varied from 240 to 800 mg COD m^???2 and average value was 497 mg COD m^???2. The biofilm mass varied from 880 to 1,080 mg m^???2. The percentage of heterotroph to biofilm mass fall within the range of 24.0–90.9% and average value was 52.9%. In the oxygen uptake rate batch tests, the biomass, growth rate constant, and lysis rate constant of autotroph could not be determined because the fraction of autotroph in biofilm was relatively few. It revealed that the degradation of organic matters, nitrification, and denitrification occurred in the trunk sewer line. But the results indicate that the condition seem favorable for nitrification.     

Use of microbial activity measurements for monitoring RBC biofilms

Fixed biomass technologies, such as rotating biological contactors or biodiscs, have been applied for wastewater depuration both in large and medium–small-sized agglomerations. Biofilm’s composition and microorganism activity are essential parameters for the successful operation and control of these systems. Biofilm’s thickness and total dry weight have been widely used for biofilm’s characterization but, actually, are not sufficient to describe biofilm activity. In fact, biofilm’s activity is not proportional to the quantity of fixed biomass, but increases with the thickness of biofilm up to a determined level called the “active thickness”. Above this level, the diffusion of nutrients through the film becomes a limiting factor. A stable, thin, and active biofilm thus offers numerous advantages in water and wastewater treatment. Different parameters have been used to evaluate biofilm’s activity. The specific oxygen uptake rate, INT-dehydrogenase activity, and the ratio active/total cells have been applied for that purpose. These methods are not only simple and rapid but also sensitive, precise, and representative. The results obtained confirm the potential of the microbial activity measurements studied for an accurate biofilm’s characterization and biomass activity estimation in fundamental research and for the practical operation and control of fixed biomass depuration systems.     

Organic speciation of atmospheric particles in Alvão Natural Park (Portugal)

PM₁₀ continental rural background aerosols were collected during a summer field campaign (August–September 2006) at Lamas de Ôlo in the upper zone of the Alvão Natural Park, a mountain region of northern Portugal. In addition to the determination of the carbonaceous content by a thermal–optical method, the organic speciation of aerosols was performed by gas chromatography–mass spectrometry in an effort to evaluate photo-oxidation products of biogenic volatile organic compounds and other markers for source characterization. The detailed analysis revealed relatively high concentrations of polyols and short-chain dicarboxylic, tricarboxylic, hydroxycarboxylic, and oxocarboxylic acids, many of which are thought to be indicators of secondary aerosol formation, accounting for about 70% of global chromatographically resolved mass. Major photo-oxidation products of α- and β-pinene have been detected. The tracers for the photo-oxidation of isoprene comprise two diastereoisomeric 2-methyltetrols, C₅-alkene triols, and 2-methylglyceric acid, which have only recently been elucidated. In addition, the occurrence of levoglucosan and other biomass combustion tracers indicates that the site was affected by wildfires. This source contributed to more than 80% of the organic carbon mass during a period of strong forest fire influence.     

Multiscale satellite and spatial information and analysis framework in support of a large-area forest monitoring and inventory update

Many countries undertake a national forest inventory to enable statistically valid monitoring in support of national and international reporting of forest conditions and change. Canada’s National Forest Inventory (NFI) program is designed to operate on a 10-year remeasurement cycle, with an interim report produced at the 5-year mid-point. The NFI is a sample-based inventory, with approximately 18,850 2 ×2-km photo plots across the country, distributed on a 20×20-km grid of sample points; these photo plots are the primary data source for the NFI. Capacity to provide annual monitoring information is required to keep policy and decision makers apprised of current forest conditions. In this study, we implemented a multistage monitoring framework and used a Moderate Resolution Imaging Spectroradiometer (MODIS) change product to successfully identify 78% of the changes in forest cover area that were captured with a Landsat change detection approach. Of the NFI photo plots that were identified by both the Landsat and MODIS approaches as having changes in forest cover, the proportion of change area within the plots was similar (R ²?=?0.78). Approximately 70% of the Landsat-derived change events occupied less than 40% of a single MODIS pixel, and more than 90% of the change events of this size were successfully detected with the MODIS product. Finally, MODIS estimates of the proportion of forest cover change at the NFI photo plot level were comparable to change estimates for the ecoregions as a whole (R ²?=?0.95). High-temporal, low-spatial resolution imagery such as MODIS, in combination with other remotely sensed data sources, can provide information on disturbance events within a national forest inventory remeasurement cycle, thereby satisfying the interim information needs of policy and decision makers as well as the requirements of national and international reporting commitments.     

Serial batch leaching procedure for characterization of coal fly ash

Although many leaching methods have been used for various purposes by research groups, industries, and regulators, there is still a need for a simple but comprehensive approach to leaching coal utilization by-products and other granular materials in order to estimate potential release of heavy metals when these materials are exposed to natural fluids. A serial batch characterization method has been developed at the National Energy Technology Laboratory that can be completed in 2–3 days to serve as a screening tool. The procedure provides an estimate of cumulative metals release under varying pH conditions, and leaching the sample at increasing liquid/solid ratios can indicate the rate at which this process will occur. This method was applied to eight fly ashes, adapted to the acidic or alkaline nature of the ash. The leachates were analyzed for 30 elements. The test was run in quadruplicate, and the relative standard deviation (RSD) was used as a measure of method reproducibility. RSD values are between 0.02 and 0.70, with the majority of the RSD values less than 0.3. The serial batch leaching procedure was developed as a simple, relatively quick, yet comprehensive method of estimating the risk of heavy metal release from fly ash when it is exposed to natural fluids, such as acid rain or groundwater. Tests on a random selection of coal fly ashes have shown it to be a reasonably precise method for estimating the availability and long-term release of cations from fly ash.     

Chemical-mineralogical characterisation of coarse recycled concrete aggregate

The construction industry is now putting greater emphasis than ever before on increasing recycling and promoting more sustainable waste management practices. In keeping with this approach, many sectors of the industry have actively sought to encourage the use of recycled concrete aggregate (RCA) as an alternative to primary aggregates in concrete production. The results of a laboratory experimental programme aimed at establishing chemical and mineralogical characteristics of coarse RCA and its likely influence on concrete performance are reported in this paper. Commercially produced coarse RCA and natural aggregates (16-4 mm size fraction) were tested. Results of X-ray fluorescence (XRF) analyses showed that original source of RCA had a negligible effect on the major elements and a comparable chemical composition between recycled and natural aggregates. X-ray diffraction (XRD) analyses results indicated the presence of calcite, portlandite and minor peaks of muscovite/illite in recycled aggregates, although they were directly proportioned to their original composition. The influence of 30%, 50%, and 100% coarse RCA on the chemical composition of equal design strength concrete has been established, and its suitability for use in a concrete application has been assessed. In this work, coarse RCA was used as a direct replacement for natural gravel in concrete production. Test results indicated that up to 30% coarse RCA had no effect on the main three oxides (SiO2, Al2O3 and CaO) of concrete, but thereafter there was a marginal decrease in SiO2 and increase in Al2O3 and CaO contents with increase in RCA content in the mix, reflecting the original constituent's composition.     

Pilot installation for the thermo-chemical characterisation of solid wastes

The increasing production and the large variety of wastes require operators of thermal treatment units to continuously adapt the installations or the functioning parameters to the different physical and chemical properties of the wastes. Usually, the treated waste is encountered in the form of heterogeneous mixtures. The classical tests such as thermogravimetry and calorimetric bomb operate component by component, separately. In addition to this, they can analyse only small quantities of waste at a time (a few grams). These common tests are necessary but insufficient in the global waste analysis in the view further thermal treatment. This paper presents an experimental installation, which was designed and built at the CNRS Science Division, Department of Industrial Methods, Compiègne University of Technology, France. It allows the determination of waste thermal and chemical properties by means of thermal treatment. Also, it is capable of continuously analysing significant quantities of waste (up to 50kg/h) as compared to the classical tests and it can work under various conditions: The installation reproduces the process conditions from incinerators or pyrolysis reactors. It also provides complete information on the kinetics of the waste thermal degradation and on the pollutant emissions. Using different mixtures of components present in the municipal solid waste and also in the reconstituted MSW samples, we defined a series of criteria for characterising waste behaviour during the stages of the main treatment process such as: feeding, devolatilisation/oxidation, advancement, solid residue evacuation, and pollutants emission.     

Road soil retention of Pb leached from MSWI bottom ash

Municipal solid waste incinerator (MSWI) bottom ash may be used as a road construction material; it potentially contains however a sizable quantity of heavy metals, which under the effect of rainfall infiltration through the road structure can be leached out from the material and infiltrate into the underlying soil. An eco-compatibility assessment of MSWI bottom ash reuse in road construction applications necessitates examining the solubility and retention of heavy metals in road soils. This study is dedicated to Pb transfer, sorption and desorption (NEN 7341 standard test) within various soils. These experiments yield results relative to the interaction between road soils and an MSWI bottom ash leachate representative of a "fresh" product, with a high leaching potential. For the soils investigated, the sorption of lead varies between 90% and 99%. For an extraction at pH 7, Pb release is very low (<2%) for all soils, while at pH 4 leaching varies between 4% and 47%. This work shows that Pb may be fixed by some types of road soil in mostly stable forms.     

Composition of a Spanish sewage sludge and effects on treated soil and olive trees

The effects of sewage sludge (SL) application on the soil and olive trees (Olea europaea L., cultivar: cornicabra) were studied. The plants were grown in 8.5L pots and subjected to the following treatments: 0, 3.66, 7.32, 14.65, 29.3, 58.6, and 117.2 g SL kg(-1) soil that corresponded, respectively, to 0, 4, 8, 16, 32, 64 and 128 M g ha(-1) dry weight of sewage sludge. The application of SL at the rates 64 and 128 M g ha(-1) produced leaf tip burning and leaf drop after 120 days, although cumulative metal pollutant loading rates was below USEPA and European regulations. This toxicity symptom could be caused by the high sodium levels in the leaves (over 0.19%), which can damage olive tree development. The Na contents of leaves were well correlated with soil Na content (r2: 0.91). In general, SL rates significantly increased the level of Cr, Ni, Cu, Zn, Cd and Pb in soil and plants, but these concentrations were in the normal ranges, except for the Zn concentration, which was over the critical soil content for the rates of 32, 64, 128 Mg ha(-1) but not in the leaves. Results suggested that regulations about the utilization of sewage sludge on agricultural land should consider the limit values for salt, and not only metals, that may be added to soil, in order to minimize the risk of negative effects to plant health.     

Bioaccumulation of anthropogenic contaminants by detritivorous fish in the Río de la Plata estuary: 1-aliphatic hydrocarbons

The temporal variability and bioaccumulation dynamics of C_12–25 n-alkanes, isoprenoids and unresolved aliphatic hydrocarbons (UCM) were studied in a detritivorous fish (Sábalo: Prochilodus lineatus) collected from 1999 to 2005 in the sewage impacted Buenos Aires coastal area. Fish muscles contain huge amounts of n-C_12–25 (165 ± 93, 70 ± 48 or 280 ± 134 μg g⁻¹, dry, fresh and lipid weight, respectively) and UCM (931 ± 560, 399 ± 288 and 1567 ± 802 μg g⁻¹) reflecting the chronic bioaccumulation of fossil fuels from sewage particulates. On a temporal basis, lipid normalized aliphatic concentrations peaked by the end of 2001–2002 during the rainiest period over the last four decades (1750 vs. 1083 ± 4.6 mm in 1999, 2004 and 2005), reflecting an enhanced exposition due to massive anthropogenic fluxes from Metropolitan Buenos Aires in wet years. The hydrocarbon composition in fish muscles is enriched in n-C_15–17 and isoprenoids relative to a fresh crude oil and settling particulates, with fresher signatures during the 2001–2002 maxima. Fish/settling material bioaccumulation factors (BAFs: 0.4–6.4 dry weight or 0.07–0.94 lipid-organic carbon) plotted against K_ow showed a parabolic pattern maximizing at n-C_14–18 and isoprenoids. The optimal bioaccumulation window corresponds to highly hydrophobic (log K_ow: 7.2–9.9), intermediate-size C_14–18 n-alkanes and C_15–20 isoprenoids (MW: 198–282; length: 17.9 to 25.4 Å) with melting points ranging from −19.8 to 28 °C. The uptake efficiency is inversely correlated to melting points and increased from 75% for n-C₂₅ to above 90% for n-C_14–15 and isoprenoids.