Development of an ombrotrophic peat bog (low ash) reference material for the determination of elemental concentrations

Given the increasing interest in using peat bogs as archives of atmospheric metal deposition, the lack of validated sample preparation methods and suitable certified reference materials has hindered not only the quality assurance of the generated analytical data but also the interpretation and comparison of peat core metal profiles from different laboratories in the international community. Reference materials play an important role in the evaluation of the accuracy of analytical results and are essential parts of good laboratory practice. An ombrotrophic peat bog reference material has been developed by 14 laboratories from nine countries in an inter-laboratory comparison between February and October 2002. The material has been characterised for both acid-extractable and total concentrations of a range of elements, including Al, As, Ca, Cd, Cr, Cu, Fe, Hg, Mg, Mn, Na, Ni, P, Pb, Ti, V and Zn. The steps involved in the production of the reference material (i.e. collection and preparation, homogeneity and stability studies, and certification) are described in detail.     

The fate of fipronil in modular estuarine mesocosms

The degradation and corresponding product manifold for the pesticide fipronil was determined in three replicate estuarine mesocosms. Aqueous fipronil concentrations rapidly decreased over the 672 h timescale of the experiment (95% removal). Loss was apparently first-order in fipronil, although there appeared to be a change in the removal mechanism after 96 h that corresponded to a dramatic slowdown in its disappearance. The reduction product of fipronil, fipronil sulfide, was not detected in the water column; however, it formed rapidly in sediments and was identified as the major product of fipronil degradation in the system (20% yield at 672 h, with respect to initial fipronil concentration). Fipronil sulfone is thought to form primarily via biological oxidation; and, although it was generated rapidly in the water column (10% yield), only trace amounts were detected in the sediment (1% yield). The direct photolysis product of fipronil, fipronil desulfinyl, was present in all samples; it formed rapidly in the water column (4% yield) and partitioned into the sediment phase (7% yield) over the course of the experiment. The mass balance on fipronil and associated products was 42% at 672 h.     

Distribution of Iron, Manganese, Zinc and Atrazine in Groundwater in Parts of Palar and Cheyyar River Basins, South India

A study was carried out in a part of Palar and Cheyyar river basin to evaluate the current status of iron, manganese, zinc and atrazine concentrations, their origin and distribution in groundwater. Groundwater samples were collected during post-monsoon (March 1998 and February 1999) and pre-monsoon (June 1999) periods from 41 sampling wells distributed throughout the study area. The groundwater samples were analyzed for trace metals using AAS and atrazine using HPLC. The concentration of the trace elements in groundwater is predominant during pre-monsoon period. Distribution pattern indicates that the concentration of these elements increases from west to northeast and towards Palar river. Lower concentrations in the central part may be due to recharge of fresh water from the lakes located here. During most of the months, as there is no flow in Palar river, the concentrations of trace elements in groundwater are high. Drinking water standards indicate that Mn and Zn cross the permissible limit recommended by EPA during the pre-monsoon period. A comparison of groundwater data with trace element chemistry of rock samples shows the abundance of trace elements both in the rock and water in the order of Fe > Mn > Zn and Fe > Zn > Mn. This indicates that iron in groundwater is derived from lithogenic origin. Further, Fe, Mn and Zn have good correlation in rock samples, while it is reverse in the case of water samples, indicating the non-lithogenic origin of Mn and Zn. Atrazine (a herbicide) was not detected in any of the groundwater samples in the study area, perhaps due to low-application rate and adsorption in the soil materials.     

Exposure and inhalation risk assessment in an aluminium cast-house

To date the exposure, absorption and respiratory health effects of cast-house workers have not been described since most studies performed in the aluminium industry are focused on exposure and health effects of potroom personnel. In the present study, we assessed the external exposure and the absorbed dose of metals in personnel from the aluminium cast house. This was combined with an evaluation of respiratory complaints and the lung function of the personnel. 30 workers from an aluminium casting plant participated and 17 individuals of the packaging and distribution departments were selected as controls. The exposure was assessed by the quantification of total inhalable fume with metal fraction and by the determination of urinary aluminium, chromium, beryllium, manganese and lead concentration. Carbon monoxide (CO), carbon dioxide (CO2), aldehydes and polyaromatic hydrocarbons and man-made mineral fibres concentration were assessed as well. In order to evaluate their respiratory status each participant filled out a questionnaire and their lung function was tested by forced spirometry. Total inhalable fume exposure was maximum 4.37 mg m(-3). Exposure to the combustion gases, man-made mineral fibres and metal fume was well below the exposure limits. Beryllium could not be detected in the urine. The values of aluminium, manganese and lead in the urine were all under the respective reference value. One individual had a urinary chromium excretion above the ACGIH defined biological exposure index (BEI) of 30 microg g(-1) creatinine. There was no significant difference in any of the categories of the respiratory questionnaire and in the results of the spirometry between cast house personnel and referents (Chi-square, all p > 0.05). Exposure in cast houses seem to be acceptable under these conditions. However, peak exposure to fumes cannot be excluded and the potential risk of chromium and beryllium exposure due to the recycling of aluminium requires further attention.     

Large-scale mercury variations in Lake Vänern (Sweden) 1974-98

Lake V?nern, the largest lake in Sweden, has been seriously contaminated with mercury during the 20th century. In the 1970's and 80's the direct load, mainly from a chlor-alkali industry in the area, of mercury was drastically reduced as a response to new legislation, from three to five tons down to between five and ten kg yr(-1). Large amounts of the disposed pollutant have accumulated in the sediments. The question posed in this work is now, is the effect of the drastic load reduction after more than two decades visible in the sediments? The question is relevant as large areas still are blacklisted for fishing, but also as a follow-up of a major remedy action. The lake also serves as a freshwater reservoir for even Sweden's second largest city. This work synthesises and compares data of mercury in the sediments from three major field programs, in 1974, 1984 and 1998. The interest is focused on both spatial heterogeneity and temporal trends. In 1974, the surface concentrations are significantly higher than in subsequent surveys. Significant differences are also found between 1984 and 1998. Significant spatial differences within the lake are found for respective year. The most contaminated area is located in the north, close to the major point source (a former chlor-alkali industry). This is also the area with the largest improvement, as a direct response to the reduction in load. Further from the outlet, the recovery is more affected by burial and transport processes out into the deeper basins.     

Examples of the role of analytical chemistry in environmental risk management research

Analytical chemistry is an important tier of environmental protection and has been traditionally linked to compliance and/or exposure monitoring activities for environmental contaminants. The adoption of the risk management paradigm has led to special challenges for analytical chemistry applied to environmental risk analysis. Namely, methods developed for regulated contaminants may not be appropriate and/or applicable to risk management scenarios. This paper contains examples of analytical chemistry applied to risk management challenges broken down by the analytical approach and analyte for some selected work in our laboratory. Specific techniques discussed include stable association complex electrospray mass spectrometry (cESI-MS), gas chromatography-mass spectrometry (GC-MS), split-flow thin cell (SPLITT) fractionation and matrix-assisted laser desorption time of flight mass spectrometry (MALDI-ToF-MS). Specific analytes include haloacetic acids (HAA9), perchlorate, bromate, triazine degradation products, metal-contaminated colloids and Cryptosporidium parvum oocysts.     

The collection of PM10 for toxicological investigation: comparisons between different collecting devices

A positive correlation has been established between increased levels of airborne particulate pollution and adverse health effects, the toxicological mechanisms of which are poorly understood. For toxicologists to unambiguously determine thesemechanisms, truly representative samples of ambient PM₁₀ are required. This presents problems, as PM₁₀ collecting equipment commonly employed, such as the Tapered Element Oscillating Microbalance (TEOM®), heat the inflow toexclude moisture or use fibrous filters, resulting in a PM₁₀sample that may have undergone significant chemical change on thefilter surface or is contaminated by filter fibres. Other systems(i.e. Negretti and Partisol) can successfully collect PM₁₀ without chemical alteration or filter contamination. Comparativecollections from Port Talbot, S. Wales suggest that TEOMs and Negretti/Partisol systems collect different PM₁₀'s; the principle difference arising from the TEOM's heating chamber, which precipitates water-soluble ions and volatilises some organic components. This results in both the mass and compositionof the PM₁₀'s being altered. Particle size distributionsfor Negretti and Partisol collections highlighted differences mainly attributed to different flow rates. The results of thiswork demonstrate that simple correlations between PM₁₀ massand adverse health effects are problematic. Furthermore, elucidation of the complex fractionation and chemical changes indifferent collectors is necessary.     

Air pollution exposure monitoring and estimation. Part VI. Ambient exposure of adults in an industrialised region

This paper presents methodology and results of a dynamic individual air pollution exposure model (DINEX) that calculates the hourly exposure for each adult in a panel study. Each of over 260 participants, through the use of a diary, provided information used in the model to calculate his/her personal, individualised exposure. The participants filled out the diary daily, hour by hour, over two, two month periods. The exposure assessment model coupled the diary information and results of an indoor/outdoor measurement program, with the results of dispersion modelling on an hourly basis for an industrial area in Norway. The estimated air pollution concentrations from the dispersion model, based on continuous meteorological measurements, were calibrated with air pollutant concentrations measured continuously.     

Collaborative study to improve the quality control of rare earth element determinations in environmental matrices

In order to control the quality of rare earth determinations in environmental matrices, the Standards, Measurements and Testing Programme (formerly Community Bureau of Reference, BCR) of the European Commission has started a project, the final aim of which is to certify four types of matrices (tuna muscle, mussel tissue, aquatic plant and estuarine sediment) for their contents of a range of rare earth elements (Sc, Y and the lanthanides: La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Yb and Lu). The elements U and Th were added to the study. The first part of this project consisted of an interlaboratory study which aimed to test the feasibility of preparation of environmental reference materials and to detect and remove most of the pitfalls observed in rare earth determinations. This paper presents the preparation of the four matrices for the intercomparison study and for the candidate reference material. The main results are presented of the interlaboratory study that was carried out prior to the certification campaign. This collaborative trial is the first attempt ever carried out at this scale to evaluate the state-of-the-art of rare earth determinations in the environment. Its impact on the improvement of chemical measurements will have positive effects on the comparability of data necessary for environmental monitoring.     

Evaluation of two adsorbents for diffusive sampling and thermal desorption-gas chromatographic analysis of monoterpenes in air

Tube type samplers with two different adsorbents, Chromosorb 106 and Tenax TA, were evaluated by laboratory experiments and field tests for simultaneous diffusive sampling of alpha-pinene, beta-pinene and delta 3-carene and subsequent thermal desorption-gas chromatographic analysis. No statistically significant effects of exposure time, concentrations of monoterpenes or relative humidity were found for samplers with Chromosorb 106 when running a factorial design, with the exception of the adsorption of delta 3-carene, for which some weak effects were noted. Samplers with Tenax TA were affected by the sampling time as well as the concentration for all terpenes, with a strong interaction effect between these two factors. The terpenes showed good storage stability on both adsorbents. No effect of back-diffusion was noted when using Chromosorb 106, while Tenax TA showed some back-diffusion effects. The uptake rates, in ml min-1, for the terpenes on Chromosorb 106 were 0.36 for alpha-pinene, 0.36 for beta-pinene and 0.40 for delta 3-carene. The corresponding average values on Tenax TA were 0.30 for alpha-pinene, 0.32 for beta-pinene and 0.38 for delta 3-carene. The field validation proved that diffusive sampling on Chromosorb 106 agreed well with pumped sampling on charcoal for stationary samples, while the personal samples indicated a discrepancy of 25% between Chromosorb 106 and charcoal samples. Tenax TA generally gave lower results than Chromosorb 106 in all field samples. Samplers packed with Chromosorb 106 could be used to monitor terpene levels in workplaces such as sawmills. The major advantages with this method are the sampling procedure, which is simple to perform compared to other techniques, the easily automated analysis procedure and the possibility to reuse the samplers.