TPH-contaminated Mexican Refinery Soil: Health Risk Assessment and the First Year of Changes

The soil of a coastal Mexican refinery is quite contaminated, especially by hydrocarbons, with detected concentrations up to 130000 mg kg(-1) as TPHs (total petroleum hydrocarbons). The main sources of contamination are pipelines, valves, and old storage tanks, besides the land disposal of untreated hydrocarbon sediments derived from the cleaning of storage tanks. A health risk assessment (HRA) was carried out in order to measure the risk hazard indexes and clean-up standards for the refinery soil. HRA suggested the following actions to be taken: benzene concentrations must be reduced in eight of the 16 studied refinery zones to 0.0074-0.0078 mg kg(-1). Also, vanadium concentration must be reduced in two zones up to a concentration of 100 mg kg(-1). In only one of all of the studied zones, benzo(a)pyrene concentration must be reduced to 0.1 mg kg(-1). After 1 yr, TPHs showed a diminution of about 52%. Even though TPHs concentrations were variable, during 1999 the average concentrations were as much as 15.5 times the goal concentration. For year 2000, TPHs concentrations were only 7.4-fold the proposed value. For the 1999-2000 period, PAHs (polycyclic aromatic hydrocarbons) concentrations decreased by 82%. Some PAHs with 2, 3, 4, and 5 aromatic rings were removed up to 100% values.     

Effects of Roadway Crossings on Leaf Litter Processing and Invertebrate Assemblages in Small Streams

The effects of the Maine Turnpike (Interstate 95) on leaf litter processing were examined in five first- and second-order coastal plain streams in southern Maine, U.S.A. Invertebrate assemblages and red maple leaf softening and loss rates were compared at 53 stations arrayed upstream and downstream of the turnpike. Litter softening rate was not affected by the roadway. Litter loss rate was significantly faster at downstream stations (-0.0024 degree-day(-1)) than at upstream stations or at stations nearest the roadway, which were not different from each other (-0.0022 degree-day(-1)). Litter softening and loss rates were more strongly related to physical and chemical habitat variables than to shredder assemblage characteristics. Significant among-stream differences were observed in most community structural metrics and in biomass of important shredder taxa, but effects of the roadway were rarely consistent among streams. This is attributed in part to habitat variation, which was greater among streams than within streams. This study suggests that while the presence of the Maine Turnpike may influence stream water quality and habitat structure, the relatively subtle effects of roadway runoff and associated habitat modifications on stream ecosystem processes are masked by within- and among-stream variability in litter processing and leaf pack invertebrate assemblage structure.     

High frequency monitoring of the coastal marine environment using the MAREL buoy

The MAREL Iroise data buoy provides physico-chemical measurements acquired in surface marine water in continuous and autonomous mode. The water is pumped 1.5 m from below the surface through a sampling pipe and flows through the measuring cell located in the floating structure. Technological innovations implemented inside the measuring cell atop the buoy allow a continuous cleaning of the sensor, while injection of chloride ions into the circuit prevents biological fouling. Specific sensors for temperature, salinity, oxygen and fluorescence investigated in this paper have been evaluated to guarantee measurement precision over a 3 month period. A bi-directional link under Internet TCP-IP protocols is used for data, alarms and remote-control transmissions with the land-based data centre. Herein, we present a 29 month record for 4 parameters measured using a MAREL buoy moored in a coastal environment (Iroise Sea, Brest, France). The accuracy of the data provided by the buoy is assessed by comparison with measurements of sea water weekly sampled at the same site as part of SOMLIT (Service d'Observation du Milieu LIToral), the French network for monitoring of the coastal environment. Some particular events (impact of intensive fresh water discharges, dynamics of a fast phytoplankton bloom) are also presented, demonstrating the worth of monitoring a highly variable environment with a high frequency continuous reliable system.     

Organochlorine Pesticide Residues in Wheat and Drinking Water Samples from Jaipur, Rajasthan, India

The organochlorine pesticide contamination in dietary sources has caused serious threat to the human progeny. The present study was therefore conducted to evaluate the pesticide contamination in wheat flour and drinking water from Jaipur City, Rajasthan, India using Gas Chromatograph. All the wheat and water samples were found to be contaminated with various organochlorine pesticide residues of DDT and its metabolites, HCH and its isomers, heptachlor and its expoxide and aldrin. The amount of pesticide detected in wheat flour was higher than the permissible limits prescribed by WHO/FAO. In drinking water only a few pesticides exceeded the permissible limits. Seasonal variations of pesticides residues were also observed during the study period.     

Development and validation of methods for environmental monitoring of cyclophosphamide in workplaces

Methods to monitor contamination of workplaces with antineoplastic drugs have been developed and validated. Cyclophosphamide (CP) was used as a model compound as it is one of the most commonly used antineoplastic drugs. A wipe sampling method to detect contamination with CP at surfaces was developed. A personal air sampling method to sample gas and vapour on solid sorbent tubes and particles with filters was also developed. Wipe and filter samples were extracted and sorbent samples were eluted, all with ethyl acetate. The samples were analysed with liquid chromatography tandem mass spectrometry. (2)H(6)-labelled cyclophosphamide was used as an internal standard. The between-day precision was 2-5% for wipe samples, 4-6% for sorbent samples and 3-8% for filter samples. The limit of detection was 0.02 ng CP per sample for the wipe and filter methods and 0.03 ng CP per sample for the solid sorbent method. Wipe sampling on surfaces made of different materials resulted in mean recoveries between 78-106%. The desorption recovery was between 97-102% for the wipe samples, 97% for the sorbent samples and 101% for the filter samples. Samples were stable for up to 2 months at 5 degrees C and -20 degrees C and for about 2 d at room temperature. The developed methods were applied to the measurement of contamination with CP in a hospital pharmacy. Trace amounts of CP, 1.3 and 1.4 ng, were detected on surfaces in the pharmacy.     

A combination of micro-porous membrane liquid-gas extraction and solid-phase trapping for ultra trace determination of benzene in urine

A method was developed for the determination of benzene in urine. The sample was pumped through the donor channel of a membrane extraction unit with a micro-porous membrane, separating the donor channel from an identical acceptor channel purged with nitrogen. The analyte reached the acceptor channel by diffusion through the membrane and was then swept by the carrier to a solid sorbent tube, where it was trapped. The analyte was subsequently thermally desorbed and analyzed by gas chromatography (GC) with mass selective detection (MS). After optimization, the recovery was close to quantitative, or 95%. Purging the membrane unit with pure water in between the samples eliminated any memory effects. The linearity was good in the concentration range examined (20-4000 ng l(-1)), with a correlation coefficient of 0.9996. The repeatability at 50 ng l(-1) and 400 ng l(-1) was 1.4% and 1.2%, respectively. The limit of detection was 12 ng l(-1) and the limit of quantification 35 ng l(-1). This enables assessment of benzene exposures of occupationally exposed subjects, of smokers and the majority of the general population. The developed method can be easily automated.     

Selection and Calibration of Numerical Modeling in Flow and Water Quality

Numerical modeling is frequently used in coastal engineering research and application. One possible issue associated with using this method however, is that initial outcomes might differ from expectation. Modeling manipulation addresses this issue by changing the initial parameters which in turn affects the final output results. The advancement of modeling techniques in recent years has seen a gradual but steady accruement of knowledge regarding the relationship between input parameters and possible outputs, which has resulted in improved accuracy and efficiency methods. The advancements within this field have predominantly occurred on an individual basis and as such lack standardisation. An expert numerical modeler may use this knowledge subconsciously, yet may not know how to convey it to the model users. This paper has been written to introduce a systematic intelligent coding schema designed to organise current coastal engineering modeling manipulation knowledge into a standardised format. This system is relevant to the development of appropriate strategies for improved accuracy and efficiency as well as model modification to simulate specific real phenomena in prototype application cases.     

How and why is Aquatic Quality Changing at Nahanni National Park Reserve, nwt, Canada?

Nahanni National Park Reserve is located at southwestern NWT-Yukon border. One of the first UNESCO World Heritage sites, Nahanni lies within Taiga Cordillera and Taiga Shield Ecozones. Base and precious metal mining occurred upstream of Nahanni prior to park establishment. Nahanni waters, sediments, fish, and caribou have naturally elevated metals levels. Baseline water, sediment and fish tissue quality data were collected and analyzed throughout Nahanni during 1988–91 and 1992–97. These two programs characterized how aquatic quality variables are naturally varying in space and time, affected by geology, stream flow, seasonality, and extreme meteorological and geological events. Possible anthropogenic causes of aquatic quality change were examined. Measured values were compared to existing Guidelines and site-specific objectives were established.     

Trihalomethanes in Drinking Water of Greater Québec Region (Canada): Occurrence, Variations and Modelling

The levels of trihalomethanes (THMs) – the main species of by-product from water chlorination – were monitored in thedistribution systems of the five major drinking water utilitiesof the greater area of Québec City in order to investigate andmodel their occurrence on a spatial and seasonal basis. Data forTHMs and other water quality and operational parametersassociated with their formation were generated through a 16 monthsampling program involving several sites representing variablewater residence times, from the plant to the system extremity.The results demonstrate that the differences in measured THMlevels between the five utilities are mainly due to the variablequality of raw waters, the type of water treatment process beingused and the type and levels of applied disinfectant. Dependingon the utility, average THM levels were from 1.3 to 2.5 timeshigher in the system extremities than in the water leaving thetreatment plant. Also, average levels of THMs measured in summerat the distribution system extremities were, depending on theutility, from 2.5 to 5 times higher than the average levelsmeasured in winter. The seasonal differences were found to besignificantly greater than those observed by others in waterutilities in the United States and Europe and are explained inlarge part by the considerable changes, over the year, in thequality and temperature of surface waters in Southern Québec. Forthe five utilities under study, multivariate regression modelswere developed in order to predict spatial and seasonalvariations of THMs. Both residual chlorine demand and temperaturewere found to be better, statistically, as predictors for THMoccurrence. The usefulness of the developed models for routineand long term water quality management, as well as for assessmentof human exposure to THMs, are also discussed.     

Trace Metal Concentration in Roadside Surface Soil and Tree Back: A Measurement of Local Atmospheric Pollution in Abuja, Nigeria

Cadmium, copper, lead, nickel and zinc concentrations were analysed by atomic absorption spectrophotometry in surface soil and tree bark from different districts of Abuja, Nigeria, in order to determine the atmospheric trace metal input in the area.Elevated concentrations of some of the studied metals were observed in the soil and tree bark samples from the commercial/high traffic areas of the city compared to backgroundvalues. In soil samples, the average concentration of the metals were 0.6±0.4, 18.0±4.0, 281±39, 16±4 and66±23 g g^-1 dry weight for Cd, Cu, Pb, Ni and Zn, respectively, whilst the average concentrations in tree bark were 0.3±0.2, 12±4, 133±32, 13±3 and 61±10 g g^-1 dry weight for Cd, Cu, Pb, Ni and Zn, respectively. The trend in trace metal levels suggested that automobile emissions are a major source of these metals as the highest concentrations of Pb and Zn were recorded in the commercial areas of the city known for their high traffic densities. The levels of metal in the study area were relativelylow compared to levels found in some larger and older cities in various countries worldwide.