A comparison of X-ray fluorescence and wet chemical analysis of air filter samples from a scrap lead smelting operation

Personal and area air samples were taken at a scrap lead smelter operation in a bullet manufacturing facility. Samples were taken using the 37-mm styrene-acrylonitrile closed-face filter cassette (CFC, the current US standard device for lead sampling), the 37-mm GSP or "cone" sampler, the 25-mm Institute of Occupational Medicine (IOM) inhalable sampler, and the 25-mm Button sampler (developed at the University of Cincinnati). Polyvinylchloride filters were used for sampling. The filters were pre- and post-weighed, and analyzed for lead content using a field-portable X-ray fluorescence (XRF) analyzer. The filters were then extracted with dilute nitric acid in an ultrasonic extraction bath and the solutions were analyzed by inductively coupled plasma optical emission spectroscopy. The 25-mm filters were analyzed using a single XRF reading, while three readings on different parts of the filter were taken from the 37-mm filters. The single reading from the 25-mm filters was adjusted for the nominal area of the filter to obtain the mass loading, while the three readings from the 37-mm filters were inserted into two different algorithms for calculating the mass loadings, and the algorithms were compared. The IOM sampler was designed for material collected in the body of the sampler to be part of the collected sample as well as that on the filter. Therefore, the IOM sampler cassettes were rinsed separately to determine if wall-loss corrections were necessary. All four samplers gave very good correlations between the two analytical methods above the limit of detection of the XRF procedure. The limit of detection for the 25-mm filters (5 microg) was lower than for the 37-mm filters (10 microg). The percentage of XRF results that were within 25% of the corresponding ICP results was evaluated. In addition, the bias from linear regression was estimated. Linear regression for the Button sampler and the IOM sampler using single readings and the GSP using all tested techniques for total filter loading gave acceptable XRF readings at loadings equivalent to sampling at the OSHA 8-hour Action Level and Permissible Exposure Limit. However, the CFC only had acceptable results when the center reading corrected for filter area was used, which was surprising, and may be a result of a limited data set. In addition to linear regression, simple estimation of bias indicated reasonable agreements between XRF and ICP results for single XRF readings on the Button sampler filters, (82% of the individual results within criterion), and on the IOM sampler filters (77% or 61%--see text), and on the GSP sampler filters using the OSHA algorithm (78%). As a result of this pilot project, all three samplers were considered suitable for inclusion in further field research studies.     

Development and validation of methods for environmental monitoring of cyclophosphamide in workplaces

Methods to monitor contamination of workplaces with antineoplastic drugs have been developed and validated. Cyclophosphamide (CP) was used as a model compound as it is one of the most commonly used antineoplastic drugs. A wipe sampling method to detect contamination with CP at surfaces was developed. A personal air sampling method to sample gas and vapour on solid sorbent tubes and particles with filters was also developed. Wipe and filter samples were extracted and sorbent samples were eluted, all with ethyl acetate. The samples were analysed with liquid chromatography tandem mass spectrometry. (2)H(6)-labelled cyclophosphamide was used as an internal standard. The between-day precision was 2-5% for wipe samples, 4-6% for sorbent samples and 3-8% for filter samples. The limit of detection was 0.02 ng CP per sample for the wipe and filter methods and 0.03 ng CP per sample for the solid sorbent method. Wipe sampling on surfaces made of different materials resulted in mean recoveries between 78-106%. The desorption recovery was between 97-102% for the wipe samples, 97% for the sorbent samples and 101% for the filter samples. Samples were stable for up to 2 months at 5 degrees C and -20 degrees C and for about 2 d at room temperature. The developed methods were applied to the measurement of contamination with CP in a hospital pharmacy. Trace amounts of CP, 1.3 and 1.4 ng, were detected on surfaces in the pharmacy.     

Using improved neural network model to analyze RSP,NOx and NO2 levels in urban air in Mong Kok,Hong Kong

As the health impact of air pollutants existing in ambient addresses much attention in recent years, forecasting of airpollutant parameters becomes an important and popular topic inenvironmental science. Airborne pollution is a serious, and willbe a major problem in Hong Kong within the next few years. InHong Kong, Respirable Suspended Particulate (RSP) and NitrogenOxides NO_x and NO₂ are major air pollutants due to thedominant diesel fuel usage by public transportation and heavyvehicles. Hence, the investigation and prediction of the influence and the tendency of these pollutants are ofsignificance to public and the city image. The multi-layerperceptron (MLP) neural network is regarded as a reliable andcost-effective method to achieve such tasks. The works presentedhere involve developing an improved neural network model, whichcombines the principal component analysis (PCA) technique and theradial basis function (RBF) network, and forecasting thepollutant levels and tendencies based in the recorded data. Inthe study, the PCA is firstly used to reduce and orthogonalizethe original input variables (data), these treated variables arethen used as new input vectors in RBF neural network modelestablished for forecasting the pollutant tendencies. Comparingwith the general neural network models, the proposed modelpossesses simpler network architecture, faster training speed,and more satisfactory predicting performance. This improvedmodel is evaluated by using hourly time series of RSP, NO_x and NO₂ concentrations collected at Mong Kok Roadside Gaseous Monitory Station in Hong Kong during the year 2000. By comparing the predicted RSP, NO_x and NO₂ concentrationswith the actual data of these pollutants recorded at the monitorystation, the effectiveness of the proposed model has been proven.Therefore, in authors' opinion, the model presented in the paper is a potential tool in forecasting air quality parameters and hasadvantages over the traditional neural network methods.     

Trihalomethanes in Drinking Water of Greater Québec Region (Canada): Occurrence, Variations and Modelling

The levels of trihalomethanes (THMs) – the main species of by-product from water chlorination – were monitored in thedistribution systems of the five major drinking water utilitiesof the greater area of Québec City in order to investigate andmodel their occurrence on a spatial and seasonal basis. Data forTHMs and other water quality and operational parametersassociated with their formation were generated through a 16 monthsampling program involving several sites representing variablewater residence times, from the plant to the system extremity.The results demonstrate that the differences in measured THMlevels between the five utilities are mainly due to the variablequality of raw waters, the type of water treatment process beingused and the type and levels of applied disinfectant. Dependingon the utility, average THM levels were from 1.3 to 2.5 timeshigher in the system extremities than in the water leaving thetreatment plant. Also, average levels of THMs measured in summerat the distribution system extremities were, depending on theutility, from 2.5 to 5 times higher than the average levelsmeasured in winter. The seasonal differences were found to besignificantly greater than those observed by others in waterutilities in the United States and Europe and are explained inlarge part by the considerable changes, over the year, in thequality and temperature of surface waters in Southern Québec. Forthe five utilities under study, multivariate regression modelswere developed in order to predict spatial and seasonalvariations of THMs. Both residual chlorine demand and temperaturewere found to be better, statistically, as predictors for THMoccurrence. The usefulness of the developed models for routineand long term water quality management, as well as for assessmentof human exposure to THMs, are also discussed.     

Sharing the geo-Referenced Results of Climate Change Impact Research

The Prairie Adaptation Research Collaborative (PARC) has implemented an Internet Map Server (IMS) at the PARC web site (www.parc.ca) to 1) disseminate the geo-referenced results of PARC sponsored research on climate change impacts and adaptation, and 2) address data, information and knowledge management within the PARC network of researchers and partners. PARC facilitates interdisciplinary research on adaptation to the impacts of climate change in the Canadian Prairie Provinces. The web site is intended as a platform for sharing information and encouraging discussion of climate change impacts and adaptation. The IMS enables scientists and stakeholders to apply simple climate change scenarios to geo-referenced biophysical and social data, and dynamically create maps that display the geographic distribution of potential impacts of climate change. With a limited capacity for spatial analysis, most geo-processing and the climate impact modeling is done offline within a GIS environment. The IMS will serve the output from climate impact models, such that the model results can be customized by the web site user and be most readily applied to the planning and analysis of adaptation strategies.     

Application of the benthic index of biotic integrity to environmental monitoring in Chesapeake Bay

The Chesapeake Bay benthic index of biotic integrity (B-IBI) was developed to assess benthic community health and environmental quality in Chesapeake Bay. The B-IBI provides Chesapeake Bay monitoring programs with a uniform tool with which to characterize bay-wide benthic community condition and assess the health of the Bay. A probability-based design permits unbiased annual estimates of areal degradation within the Chesapeake Bay and its tributaries with quantifiable precision. However, of greatest interest to managers is the identification of problem areas most in need of restoration. Here we apply the B-IBI to benthic data collected in the Bay since 1994 to assess benthic community degradation by Chesapeake Bay Program segment and water depth. We used a new B-IBI classification system that improves the reliability of the estimates of degradation. Estimates were produced for 67 Chesapeake Bay Program segments. Greatest degradation was found in areas that are known to experience hypoxia or show toxic contamination, such as the mesohaline portion of the Potomac River, the Patapsco River, and the Maryland mainstem. Logistic regression models revealed increased probability of degraded benthos with depth for the lower Potomac River, Patapsco River, Nanticoke River, lower York River, and the Maryland mainstem. Our assessment of degradation by segment and water depth provided greater resolution of relative condition than previously available, and helped define the extent of degradation in Chesapeake Bay.     

Application of a systemic approach to the study of pollution of the Tinto and Odiel rivers (Spain)

The province of Huelva in the SW of Spain presents high environmental contrasts: together with the great abundance of natural spaces, it shows the impacts of historical natural resources exploitation processes. In the Ria of Huelva, the effluents of the chemical industries must be added to the contaminating inputs of the Tinto and Odiel rivers, coming from the acid drainage of the mines located in the Iberian Pyrite Belt. This forced the Environmental Agency (AMA) to elaborate in 1987 an Effluent Remediation Plan in order to negate unacceptable environmental impacts. The application of a grey box systemic analysis to the AMD pollution, undergone by the Tinto and Odiel rivers has allowed to set a conclusive explanation of the sampling results observed for a period of 11 years, thus making available an overall view of the polluting process and, above all, an explanation of its partial aspects.     

A Spatial Model to Estimate Habitat Fragmentation and Its Consequences on Long-Term Persistence of Animal Populations

The increasing use of the landscape by humans has led to important diminutions of natural surfaces. The remaining patches of wild habitat are small and isolated from each other among a matrix of inhospitable land-uses. This habitat fragmentation, by disabling population movements and stopping their spread to new habitats, is a major threat to the survival of numerous plant and animal species. We developed a general model, adaptable for specific species, capable of identifying suitable habitat patches within fragmented landscapes and investigating the capacity of populations to move between these patches. This approach combines GIS analysis of a landscape, with spatial dynamic modeling. Suitable habitat is identified using a threshold area to perimeter ratio. Potential movement pathways of species between habitat patches are modeled using a cellular automaton. Habitat connectivity is estimated by overlaying habitat patches with movement pathways. The maximum potential population is calculated within and between connected habitat patches and potential risk of inbreeding within meta-populations is considered. The model was tested on a sample map and applied to scenario maps of predicted land-use change in the Peoria Tri-county region (IL). It (1) showed area of natural area alone was insufficient to estimate the consequences on animal populations; (2) underscored the necessity to use approaches investigating the effect of land-use change spatially through the landscape and the importance of considering species-specific life history characteristics; and (3) highlighted the model's potential utility as an indicator of species likelihood to be affected negatively by land-use scenarios and therefore requiring detailed investigation.     

Flow-injection analysis with fluorescence detection for the determination of trace levels of ammonium in seawater

A method using flow-injection, gas-diffusion, derivatisation and then fluorescent detection has been established for ammonium ion determination in seawater. The fluorescent derivative formed by reacting ortho-phthaldialdehyde (OPA) and sulfite with ammonia gives high sensitivity while removing potential interferences. This is required to measure the low concentrations of ammonium often seen in the open ocean. The experimental conditions (flow-rate, reagent concentrations, membrane configurations, etc.) were manipulated to improve performance. For a sample throughput of 30 samples h(-1), the limit of detection was 7 nM, the coefficient of variation was 5.7% at 800 nM, and the calibration curve was linear to at least 4 micromol L(-1). Interferences were minimised by a gaseous diffusion step. Volatile small molecular-weight amines as interferents were discriminated against by this method. They neither passed through the membrane as efficiently as ammonia, nor reacted as readily with OPA when sulfite was the reductant. Contamination by ammonia from laboratory and shipboard sources complicates application of the method to natural waters, especially measurement of low concentrations (<100 nM) in open-ocean waters. Steps to overcome contamination are described in detail. Some results are presented for ammonium determination in Southern Ocean and Huon Estuary (Tasmania) waters.