Further studies using X-ray fluorescence to sample lead contaminated carpeted surfaces

The sampling of carpeted surfaces to test for lead contamination primarily focuses upon vacuum techniques. Vacuum sampling techniques, however, require time-consuming, expensive laboratory analysis of the dusts obtained and are unable to determine total lead load on the carpet. X-ray fluorescence (XRF) analysis is an on-site, inexpensive, non-destructive, quick technique for predicting metals levels in a variety of media, such as water, soil, filter paper and painted surfaces. A 1992 study of the feasibility of XRF to analyze for lead and soil loadings on carpeted surfaces indicated that XRF can detect lead at a low enough level to warrant further study. This paper expands this earlier study and developes lead and soil loading calibration curves for three different carpet types based upon XRF lead L-beta peak areas and XRF iron and barium K-alpha peak and background areas. Results indicate that variation in the data can be reduced through modifications of the XRF analysis technique, thus reducing the statistically determined detection level, and that carpet type does affect the calibration. Detection levels of approximately 70 mg/m² for lead and 5 g/m² for soil were obtained. Overall, good agreement was found between results of this study and the earlier one. XRF shows excellent potential for quantitative analysis of lead on carpeted surfaces.     

Heavy metals in the SPM of air in the environment surrounding a ferro-alloy industrial plant in India

Prices for ferro-alloys have hardened due to the closure of plants in developed countries on account of increasingly stringent pollution control legislation, resulting in a higher cost of production. A ferro-alloy industry with a capacity of 80000 MT per annum was selected to study the nature of pollution. Because of the objectionable nature of polluting air in and around the plant it was located in a rural area where there was no other industry. The area was agriculturally active and there was no effective control system for this plant.The quality of ambient air around the plant site is discussed in this paper along with the meteorological conditions. The maximum concentration of suspended particulate matter (SPM) was 768 µg/NM³ downwind of the plant, minimum 184 µg/NM³, and the average was more than 446 µg/NM³. The presence of heavy metals, viz. Fe, Mn, Cr and Pb, was also assessed. The concentration of Fe was 50 µg/NM³ downwind and 10 µg/NM³ upwind. The concentration of other metals followed a similar trend.     

Assessing land use impacts on flood processes in complex terrain by using GIS and modeling approach

A distributed hydrologic modeling and GIS approach is applied for the assessment of land use impact in the Steinsel sub-basin, Alzette, Grand-Duchy of Luxembourg. The assessment focuses on the runoff contributions from different land use classes and the potential impact of land use changes on runoff generation. The results show that the direct runoff from urban areas is dominant for a flood event compared with runoff from other land use areas in this catchment, and tends to increase for small floods and for the dry season floods, whereas the interflow from forested, pasture and agricultural field areas contributes to the recession flow. Significant variations in flood volume, peak discharge, time to the peak, etc., are found from the model simulation based on the three hypothetical land use change scenarios.     

Application of a checklist for quality assistance in environmental modelling to an energy model

Large, complex energy models present considerable challenges to develop and test. Uncertainty assessments of such models provide only partial guidance on the quality of the results. We have developed a model quality assistance checklist to aid in this purpose. The model checklist provides diagnostic output in the form of a set of pitfalls for the model application. The checklist is applied here to an energy model for the problem of assessing energy use and greenhouse gas emissions. Use of the checklist suggests that results on this issue are contingent on a number of assumptions that are highly value-laden. When these assumptions are held fixed, the model is deemed capable of producing moderately robust results of relevance to climate policy over the longer term. Checklist responses also indicate that a number of details critical to policy choices or outcomes on this issue are not captured in the model, and model results should therefore be supplemented with alternative analyses.     

SI-traceable certification of Cu, Cr, Cd and Pb in sediment and fly ash candidate reference materials

Many fields in environmental analytical chemistry deal with very low limits and thresholds as set by governmental legislations or transnational regulations. The need for the accuracy, comparability and traceability of analytical measurements in environmental analytical chemistry has significantly increased and total uncertainties are even asked for by accreditation bodies of environmental laboratories. This paper addresses achieving these goals to guarantee accuracy, quality control, quality assurance or validation of a method by means of certified reference materials. The assessment of analytical results in certified reference materials must be as accurate as possible and every single step has to be fully evaluated. This paper presents the SI-traceable certification of Cu, Cr, Cd and Pb contents in geological and environmentally relevant matrices (three sediments and one fly ash sample). Certification was achieved using isotope dilution (ID) ICPMS as a primary method of measurement. In order to reduce significantly the number of analytical steps and intermediate samples a multiple spiking approach was developed. The full methodology is documented and total uncertainty budgets are calculated for all certified values. A non-element specific sample digestion process was optimised. All wet chemical digestion methods examined resulted in a more or less pronounced amount of precipitate. It is demonstrated that these precipitates originate mainly from secondary formation of fluorides (essentially CaF2) and that their formation takes place after isotopic equilibration. The contribution to the total uncertainty of the final values resulting from the formation of such precipitates was in general < 0.1% for all investigated elements. Other sources of uncertainty scrutinised included the moisture content determination, procedural blank determination, cross-contamination from the different spike materials, correction for spectral interferences, instrumental background and deadtime effects, as well as the use of either certified values or IUPAC data in the IDMS equation. The average elemental content in the sediment samples was 30-130 micrograms g-1 for Pb, 0.5-3 micrograms g-1 for Cd and 50-70 micrograms g-1 for Cu. Cr was measured in one sample and was about 60 micrograms g-1. The concentrations in the fly ash sample were up to 2 orders of magnitude higher. Expanded uncertainty for the investigated elements was about 3% (coverae factor k = 2) except for Cr, (measured by high resolution ICPMS), for which the expanded uncertainty was about 7% (k = 2).     

Improvement of the BCR three step sequential extraction procedure prior to the certification of new sediment and soil reference materials

The Standards, Measurements and Testing Programme (formerly BCR) of the European Commission proposed a three-step sequential extraction procedure for sediment analysis, following extensive expert consultations and two interlaboratory studies. This scheme was recently used to certify the extractable trace element contents of a sediment reference material (CRM 601). Although this procedure offers a means to ensure the comparability of data in this field, some difficulties concerning the interlaboratory reproducibility still remain, and a new project is currently being conducted to determine the causes of poor reproducibility in the extraction scheme. The final objective of the project is the certification of new sediment and soil reference materials for their extractable contents of Cd, Cr, Cu, Ni, Pb and Zn. This paper presents the results of a small-scale interlaboratory study, which aimed to test a revised version of the extraction schemes by comparing the original and the modified protocols using the CRM 601 sample. This work offers an improvement to the BCR sequential extraction procedure through intercomparison exercises. This improved procedure will allow the obtaining of CRMs to validate analytical data in the analysis of soils and sediments, and it will also facilitate comparability of data in the European Union.     

Soil properties and crop productivity as influenced by flyash incorporation in soil

Field experiments were carried out during 1996–97at Gulawathi, Muthiani and Salarpur Villages, IARI Farm, NewDelhi and NCPP Campus, Dadri to evaluate changes in soilcharacteristics and growth of wheat (Triticum aestivum L.),mustard (Brassica juncea L.), lentil (Lence esculentaMoench.), rice (Oryza sativa L.) and maize (Zea mays L.) byvarying amounts of flyash addition (up to 50t ha^-1) in soils atsowing/transplanting time of crops. Flyash addition in areasadjoining NCPP Thermal Power Plant, Dadri, Ghaziabad, U.P.ranged from 5–12 t ha^-1 yr^-1 in 1995–96. Shoot and root growthand yield of test crops at different locations after flyashincorporation resulted in beneficial effects of flyashaddition in most cases. The silt dominant texture of flyashimproved loamy sand to sandy loam textures of the surfacesoils at the farmers' fields. The increased growth in yield ofcrops with flyash incorporation was possibly due tomodifications in soil moisture retention and transmissioncharacteristics, bulk density, physico-chemical characterssuch as pH and EC and organic carbon content. The response offlyash addition in the soil on soil health and cropproductivity needs to be evaluated on long-term sustainableaspects.     

The Influence of pH on Mobility of Heavy Metals from Municipal Solid Waste Incinerator Fly Ash

Incineration has become one of the principal methods for municipal solid waste disposal particularly in all large cities throughout the world. Currently, the municipal solid waste incinerator fly ashes (MSWIF) are disposed of by landfill. The metal speciation of cadmium (Cd), chromium (Cr), copper (Cu), lead (Pb), and zinc (Zn) in MSWIF after been extracted with water at different pH values were examined using a sequential extraction procedure. The extraction sequence was as follows: (1) Exchangeable (NaOAc, pH 8.2), (2) Bound to Carbonates (NaOAc, pH 5.0), (3) Bound to metal oxides (HONH3Cl), (4) Bound to organic matters (HNO3, H2O2), and (5) Residual (HNO3, HCl, H2O2, HF, 1:3:1:3). The heavy metal contents in the extraction solutions were determined by inductively coupled plasma atomic emission spectrometry. The heavy metal concentrations in the different fractions obtained by sequential extraction show distinct distribution trends. The extractable fraction ranges from 25.5 to 88% of the total element content. With the pH of the extractant fall below the neutral and acidic ranges, the concentrations of heavy metals rise substantially due to the released of metals bound to carbonate fraction.     

Environmental and sustainability indicators and the concept of situational indicators. A systems approach

Through a systems approach indicators are shown to have the nature of variables, adopting different values or states, while other associated terms allude to special meanings assigned to specific values of the indicators. Practical implications are discussed. The concept of situational indicators of sustainability is introduced, representing a non-numerical function of both “pressures” or “driving forces” and “state” variables. A cost-effective multi-tiered approach to situational indicators is proposed. The concept of situational indicators is shown to be a particular case of indicators of systems behavior. A general systems formulation of the problem of sustainability highlights the importance of indicators of systems behavior and the central role of models in their definition.     

The efficacy of a limestone doser to mitigate stream acidification in a Maryland coastal plain stream: Implications for migratory fish species

The objective of this two-year study was to determine the efficacy of an automated limestone slurry doser to neutralize acidic pulses and improve water quality conditions for enhancing survival of early life stages of migratory fish species in a Maryland coastal plain stream. Implications for survival of early life stages of migratory fish species such as yellow perch (Perca flavescens), white perch (Morone americana), blueback herring (Alosa aestivalis) and alewife (Alosa pseudoharengus) are discussed based on the improved chemical conditions in the dosed area of the stream. Despite problems with overdosing in 1991 and failure of the stage transducer to work properly in 1992, the doser was generally effective in neutralizing acidic pulses (pH depressions) in the stream during three major rain events in both years. Chemical conditions (pH and inorganic monomeric aluminum) reported in the non-dosed area during major rainfall events were potentially stressful to both alewife and blueback herring although neither species was reported spawning in the stream during either year. Mitigating the potential impact of acidic conditions on early life stages of important migratory fish species was not sufficient to ensure spawning. It is therefore recommended that habitat improvement measures and well designed fish stocking programs be implemented concurrently with doser operations if the goal is to create optimum spawning conditions for migratory species.