Atmospheric haze: Its sources and effects on visibility in rural areas of the continental United States

Spatial and temporal trends in visibility are examined at a national level. It is shown that visibility is impaired in all antional parks approximately 90% of the time, and that eastern visibilities are about 10 times lower than western visibilities. Measurement of atmospheric particulates that affect visibility shows that sulfates associated with man-made emissions of sulfur dioxide are the single largest contributor to visibility reduction, except in the northwestern United States, where organic aerosols contribute significantly. In the East, coal fired power plants along the Ohio River Vallery contribute the most SO₂, while oil refining activities and other industrial sources in southern California, copper smelters in southern Arizona, and industrial activity along the Gulf Coast of Mexico contribute most of the SO₂, and thus sulfates, in the West.Contribution from Fourth World Wilderness Congress-Acid Rain Symposium, Denver (Estes Park), Colorado, September 11–18, 1987.The assumptions, findings, conclusions, judgments and views presented herein are those of the authors and should not be interpreted as necessarily representing official National Park Service policies.     

Organochlorine and mercury residues in Swainson's and ferruginous hawk eggs collected in North and South Dakota, 1974–79

Residues of organochlorine pesticides, polychlorinated biphenyls (PCBs), and mercury were measured in eggs of Swainson's hawks (Buteo swainsoni) and ferruginous hawks (B. regalis) collected in North and South Dakota during 1974–79. DDE was the most common compound detected in the eggs, but residues were below levels known to have adverse effects on reproduction. Other organochlorine compounds and mercury were found at low levels. Eggs of ferruginous hawks tended to contain more compounds with higher residues than eggs of Swainson's hawks.     

Exploring data quality for some inorganic and organic constituents of inhalable particulate matter (PM10)

Quality assurance (QA) assessments of air pollution data sets provide a basis for evaluating the significance of various substances in the atmosphere. For non-criteria pollutants, QA results are seldom reported in the technical literature and are often difficult to estimate. The present report provides a summary of QA results such as recovery, precision and accuracy data. Of the six trace elements and nine organic constituents compared in detail, recoveries, laboratory precision and laboratory accuracy values were 100%, ±3% to ±19% and-2 to-13% for the former group and 69% to 98%, ±7% to 23% and-15 to-34% for the later group. System precision varied from ±22% to ±47% for the trace elements and ±42% to ±83% for the organic constituents. Limitations in the interpretation of non-criteria particulate-phase pollutant data bases are discussed with some emphasis placed on receptor-modelling and risk assessment applications. Finally, the relevance of NBS certified materials for QA estimates in non-criteria air pollutant studies is also reviewed.     

Human plasma levels of POPs,and diet among native people from Uelen,Chukotka

Some of the people living in the Chukotka Peninsula of Russia depend heavily on marine mammals, but little is known of the exact dietary patterns and plasma levels of POPs among these populations. In this study, POPs levels in plasma from 50 participants from the isolated community of Uelen (Bering Strait) were determined and related to dietary information obtained through a food frequency questionnaire. The intake of marine mammals was high and the combined intake of blubber from walrus, seal and whale was a significant predictor (p < 0.01) of plasma concentrations of sum PCBs and borderline for sum CDs (p = 0.02) and sum DDTs (p = 0.04). There was a significant gender difference in the levels of POPs, and among women there was a significant increase with age. Extensive breastfeeding and lower blubber intake among women could be possible explanations for this gender difference. Despite the high intake of blubber the plasma levels of PCBs and DDTs were lower than some of those reported for the East Coast of Greenland. The geometric mean values for sum PCBs (17 congeners) and sum DDTs were 1316 ng g(-1) lipids and 563 ng g(-1) lipids, respectively. PCB 163, which partly co-eluted with PCB 138, was found in high concentrations (40% of PCB 138). This raises questions regarding the validity of using PCB 138 and PCB 153 to calculate the level of Arochlor 1260. The geometric mean of sum CDs was 518 ng g(-1) lipids. Concentrations of beta-HCH (geometric mean; 410 ng g(-1) lipids) were higher than observed for other native populations depending on marine mammals. Transportation of beta-HCH by ocean currents through the Bering Strait into the Arctic Ocean or regional point sources might explain these elevated levels.     

Integration of modeling,monitoring and laboratory observation to determine reasons for air quality violations

An attempt was made to explain ambient air quality violations in the vicinity of industrial plants. Micrometeorology, diffusion calculaations, ambient readings, and plant engineering data are all taken into consideration to ascertain whether the plant is or is not the principal offender.Scrutiny of hi-vol filters using scanning electron microscopy for particle size analysis and particle chemical make-up as an assessment technique is also described.Case histories using the above analytical techniques are discussed.Presented at the 16th National Conference on Energy and the Environment, May 23, 1979     

Further studies using X-ray fluorescence to sample lead contaminated carpeted surfaces

The sampling of carpeted surfaces to test for lead contamination primarily focuses upon vacuum techniques. Vacuum sampling techniques, however, require time-consuming, expensive laboratory analysis of the dusts obtained and are unable to determine total lead load on the carpet. X-ray fluorescence (XRF) analysis is an on-site, inexpensive, non-destructive, quick technique for predicting metals levels in a variety of media, such as water, soil, filter paper and painted surfaces. A 1992 study of the feasibility of XRF to analyze for lead and soil loadings on carpeted surfaces indicated that XRF can detect lead at a low enough level to warrant further study. This paper expands this earlier study and developes lead and soil loading calibration curves for three different carpet types based upon XRF lead L-beta peak areas and XRF iron and barium K-alpha peak and background areas. Results indicate that variation in the data can be reduced through modifications of the XRF analysis technique, thus reducing the statistically determined detection level, and that carpet type does affect the calibration. Detection levels of approximately 70 mg/m² for lead and 5 g/m² for soil were obtained. Overall, good agreement was found between results of this study and the earlier one. XRF shows excellent potential for quantitative analysis of lead on carpeted surfaces.     

Optimizing the removal of small fish passage barriers

Removing small artificial barriers that hinder upstream migrations of fish is a major problem in riparian habitat restoration. Because of budgetary limitations, it is necessary to prioritize barrier removal and repair decisions. These have usually been based on scoring and ranking procedures, which, although simple to use, can be very inefficient in terms of increasing the amount of accessible instream habitat. We develop a novel decision-making approach, based on integer programming techniques, which optimizes repair and removal decisions. Results show based on real datasets of barrier culverts located in Washington State that scoring and ranking is over 25% below the optimum on average and a full 100% below in the worst case, producing no net habitat gain whatsoever. This is compared to a dynamic programming method that was able to find optimal solutions in less than a second, even for problems with up to several hundred variables, and a heuristic method, which found solutions with less than a 1% average optimality gap in even less time.     

SI-traceable certification of Cu, Cr, Cd and Pb in sediment and fly ash candidate reference materials

Many fields in environmental analytical chemistry deal with very low limits and thresholds as set by governmental legislations or transnational regulations. The need for the accuracy, comparability and traceability of analytical measurements in environmental analytical chemistry has significantly increased and total uncertainties are even asked for by accreditation bodies of environmental laboratories. This paper addresses achieving these goals to guarantee accuracy, quality control, quality assurance or validation of a method by means of certified reference materials. The assessment of analytical results in certified reference materials must be as accurate as possible and every single step has to be fully evaluated. This paper presents the SI-traceable certification of Cu, Cr, Cd and Pb contents in geological and environmentally relevant matrices (three sediments and one fly ash sample). Certification was achieved using isotope dilution (ID) ICPMS as a primary method of measurement. In order to reduce significantly the number of analytical steps and intermediate samples a multiple spiking approach was developed. The full methodology is documented and total uncertainty budgets are calculated for all certified values. A non-element specific sample digestion process was optimised. All wet chemical digestion methods examined resulted in a more or less pronounced amount of precipitate. It is demonstrated that these precipitates originate mainly from secondary formation of fluorides (essentially CaF2) and that their formation takes place after isotopic equilibration. The contribution to the total uncertainty of the final values resulting from the formation of such precipitates was in general < 0.1% for all investigated elements. Other sources of uncertainty scrutinised included the moisture content determination, procedural blank determination, cross-contamination from the different spike materials, correction for spectral interferences, instrumental background and deadtime effects, as well as the use of either certified values or IUPAC data in the IDMS equation. The average elemental content in the sediment samples was 30-130 micrograms g-1 for Pb, 0.5-3 micrograms g-1 for Cd and 50-70 micrograms g-1 for Cu. Cr was measured in one sample and was about 60 micrograms g-1. The concentrations in the fly ash sample were up to 2 orders of magnitude higher. Expanded uncertainty for the investigated elements was about 3% (coverae factor k = 2) except for Cr, (measured by high resolution ICPMS), for which the expanded uncertainty was about 7% (k = 2).     

A study of the distribution of lead, cadmium and copper between water and kaolin, bentonite and a river sediment

Experiments were carried out to monitor the equilibrium distribution of lead, cadmium and copper between an aqueous phase modelling natural water and a solid phase modelling natural sediment, under varying conditions. The aqueous phase was analysed using ETAAS and differential pulse anodic stripping voltammetry (DPASV), whereas XRD and FTIR were used to study the solid phase. Sorption isotherms at constant pH were measured. Conditional distribution constants were calculated as functions of the pH, the time of equilibration and the amount of solid material. The results obtained stress the need for standardization of the approaches to the study of water-sediment interactions in order to be able to evaluate and compare the extensive data from field measurements and to predict these interactions.     

Soil properties and crop productivity as influenced by flyash incorporation in soil

Field experiments were carried out during 1996–97at Gulawathi, Muthiani and Salarpur Villages, IARI Farm, NewDelhi and NCPP Campus, Dadri to evaluate changes in soilcharacteristics and growth of wheat (Triticum aestivum L.),mustard (Brassica juncea L.), lentil (Lence esculentaMoench.), rice (Oryza sativa L.) and maize (Zea mays L.) byvarying amounts of flyash addition (up to 50t ha^-1) in soils atsowing/transplanting time of crops. Flyash addition in areasadjoining NCPP Thermal Power Plant, Dadri, Ghaziabad, U.P.ranged from 5–12 t ha^-1 yr^-1 in 1995–96. Shoot and root growthand yield of test crops at different locations after flyashincorporation resulted in beneficial effects of flyashaddition in most cases. The silt dominant texture of flyashimproved loamy sand to sandy loam textures of the surfacesoils at the farmers' fields. The increased growth in yield ofcrops with flyash incorporation was possibly due tomodifications in soil moisture retention and transmissioncharacteristics, bulk density, physico-chemical characterssuch as pH and EC and organic carbon content. The response offlyash addition in the soil on soil health and cropproductivity needs to be evaluated on long-term sustainableaspects.