Adaptive Management of Stream Channel Maintenance at Bridge Crossings in the Northern Tier Region,Pennsylvania1

Abstract: An adaptive management framework is applied to the problem of identifying mitigation measures for sediment deposition near bridge crossings in small streams in the Northern Tier region of northern Pennsylvania. The presence of the rigid bridge infrastructure introduces a challenge for applying adaptive management practices, because the integrity of the bridge structure itself has to be maintained regardless of the mitigation practices used in the stream channel near the bridge. In an effort to overcome the unacceptable risk that field‐scale adaptive management experiments present to rigid bridge infrastructure, an adaptive management approach for laboratory‐scale experimentation of mitigation methods at bridge crossings in the Northern Tier region is presented as a way to decrease the level of uncertainty about channel response to mitigation measures and increase the rate of learning about the effectiveness of these measures. Four cycles of adaptive management experiments are discussed to demonstrate that this approach results in fast and efficient learning about channel response to mitigation methods for the given conditions. The value of monitoring and of assessment of monitored data in the overall efficiency of the adaptive management approach is highlighted. Assessment of what was learned in the adaptive management experiment cycles presented here leads to new directions to continually improve management policies and practices in stream channels at bridge crossings in the Northern Tier region. The adaptive management process, rather than continuing with a normally risk‐averse management approach, results in opportunities for learning new information about a system’s response.     

Fast firing of tiles containing paper mill sludge, glass cullet and clay

The paper describes results obtained in the development of a previous research. We study here, in fast firing, the sintering behaviour and measure some properties of tiles containing a mixture of 60 wt% of paper mill sludge and 40 wt% of glass cullet. The behaviour of this material is compared to those displayed by materials obtained by the same mixture added with 10, 20 and 30 wt% of a natural red clay. In parallel, the same properties are measured also on a reference blend, which is presently used to produce commercial tiles. We show that powders containing 60 wt% of paper sludge and 40 wt% of glass cullet to which 30 wt% of clay is added give rise to materials that display a stable sintering process and have good hardness and strength and therefore could be used for the industrial production of tiles.     

Investigations on CO2 storage capacity in saline aquifers—Part 2: Estimation of storage capacity coefficients

Many studies on geological carbon dioxide (CO₂) storage capacity neglect the influence of complex coupled processes which occur during and after the injection of CO₂. Storage capacity is often overestimated since parts of the reservoirs cannot be reached by the CO₂ plume due to gravity segregation and are thus not accessible for storage. This work investigates the effect of reservoir parameters like depth, temperature, absolute and relative permeability, and capillary pressure on the processes during CO₂ injection and thus on estimates of effective storage capacity. The applied statistical characteristics of parameters are based on a large reservoir parameter database. Different measured relative permeability relations are considered. The methodology of estimating storage capacity is discussed. Using numerical 1D and 3D experiments, detailed time-dependent storage capacity estimates are derived. With respect to the concept developed in this work, it is possible to estimate effective CO₂ storage capacity in saline aquifers. It is shown that effective CO₂ mass stored in the reservoir varies by a factor of 20 for the reservoir setups considered. A high influence of the relative permeability relation on storage capacity is shown.     

The modelling of a hybrid combined cycle with pressurised fluidised bed combustion and CO2 capture

This study investigates the possibility of capturing CO₂ from flue gas under pressurised conditions, which could prove to be beneficial in comparison to working under atmospheric conditions. Simulations of two hybrid combined cycles with pressurised fluidised bed combustion and CO₂ capture are presented. CO₂ is captured from pressurised flue gas by means of chemical absorption after the boiler but before expansion. The results show a CO₂ capture penalty of approximately 8 percentage points (including 90% CO₂ capture rate and compression to 110 bar), which makes the efficiency for the best performing cycle 43.9%. It is 5.2 percentage points higher than the most probable alternative, i.e. using a natural gas fired combined cycle and a pulverised coal fired condensing plant separately with the same fuel split ratio. The largest part of the penalty is associated with the lower mass flow of flue gas after CO₂ capture, which leads to a decrease in work output in the expander and potential for feed water heating. The penalty caused by the regeneration of absorbent is quite low, since the high pressure permits the use of potassium carbonate, which requires less regeneration heat than for example the more commonly proposed monoethanolamine. Although the efficiencies of the cycles look promising it will be important to perform a cost estimate to be able to make a fair comparison with other systems. Such a cost estimate has not been done in this study. A significant drawback of these hybrid cycles in that respect is the complex nature of the systems that will have a negative effect on the economy.     

Geopolymerisation of silt generated from construction and demolition waste washing plants

Recycling plants that size, sort and wash construction and demolition waste can produce high quality aggregate. However, they also produce up to 80ton per hour of filter cake waste containing fine (<63mum) silt particles that is classified as inert waste and normally landfilled. This research investigated the potential to form geopolymers containing silt, which would allow this problematic waste to be beneficially reused as aggregate. This would significantly improve the economic viability of recycling plants that wash wastes. Silt filter cakes have been collected from a number of aggregate washing plants operating in the UK. These were found to contain similar aluminosilicate crystalline phases. Geopolymer samples were produced using silt and silt mixed with either metakaolin or pulverised fuel ash (PFA). Silt geopolymers cured at room temperature had average 7-day compressive strengths of 18.7MPa, while partial substitution of silt by metakaolin or PFA increased average compressive strengths to 30.5 and 21.9MPa, respectively. Curing specimens for 24h at 105 degrees C resulted in a compressive strength of 39.7MPa and microstructural analysis confirmed the formation of dense materials. These strengths are in excess of those required for materials to be used as aggregate, particularly in unbound applications. The implications of this research for the management of waste silt at construction and demolition waste washing plants are discussed.     

Bench-scale composting of source-separated human faeces for sanitation

In urine-diverting toilets, urine and faeces are collected separately so that nutrient content can be recycled unmixed. Faeces should be sanitized before use in agriculture fields due to the presence of possible enteric pathogens. Composting of human faeces with food waste was evaluated as a possible method for this treatment. Temperatures were monitored in three 78-L wooden compost reactors fed with faeces-to-food waste substrates (F:FW) in wet weight ratios of 1:0, 3:1 and 1:1, which were observed for approximately 20 days. To achieve temperatures higher than 15 degrees C above ambient, insulation was required for the reactors. Use of 25-mm thick styrofoam insulation around the entire exterior of the compost reactors and turning of the compost twice a week resulted in sanitizing temperatures (>or=50 degrees C) to be maintained for 8 days in the F:FW=1:1 compost and for 4 days in the F:FW=3:1 compost. In these composts, a reduction of >3 log(10) for E. coli and >4 log(10) for Enterococcus spp. was achieved. The F:FW=1:0 compost, which did not maintain >or=50 degrees C for a sufficiently long period, was not sanitized, as the counts of E. coli and Enterococcus spp. increased between days 11 and 15. This research provides useful information on the design and operation of family-size compost units for the treatment of source-separated faeces and starchy food residues, most likely available amongst the less affluent rural/urban society in Uganda.