Disappearance of bromopropylate residues in artichokes, strawberries and beans

Residues of Bromopropylate were determine in artichokes, strawberries and beans after foliar spray of acaricide at two rates. The rates used were 1 g/l formulated product (normal recommended) and 1.5 g/l. The residue levels of bromopropylate in the three crops after 14 days were lower than 0.7 ppm and did not exceed the Maximum Residual Level (MRL) recommended by FAO. In the artichokes and strawberries, the total concentration of residues decreased by 50% of the initial level after 2-3 days. Only trace levels of the bromopropylate residues (less than 0.01 ppm) were detected in the "hearts" of the artichokes. Bromopropylate residues in the green beans were also less than 0.8 ppm after the first day of foliar spraying. The kinetic of degradation occurred in two different steps. In the first step (4-6 days) the dissipation of bromopropylate was faster whereas in the second step (7-14 days) the loss of residues was much slower.     

The influence of pH on cadmium toxicity to the green alga Stichococcus bacillaris and on the cadmium forms present in the culture medium

Cadmium toxicity to the green alga Stichococcus bacillaris was investigated in media of pH 3-9. A significant decrease of cadmium toxicity occurred in both the acidic and alkaline ranges of pH. In media of pH 3 and 9, cadmium did not affect the dry mass content substantially. Maximum toxicity of cadmium was noticed at pH 6-7. Voltametric investigations showed a significant effect of pH on electrochemically measured cadmium content in the culture media. Hydrolysis of the medium components and formation of cadmium complexes with OH(-) ions caused a considerable decrease in amounts of electrochemically measured cadmium in the alkaline range of pH.     

Air Pollution in Singapore: Its Multielemental Aspect as Measured by Nuclear Analytical Techniques

Aerosol samples were collected in 1994 in Singapore on two occasions: once in June during the normal meteorological conditions and later in October during a long haze period caused by the heavy forest fire in Indonesia. Filtration and impaction collection methods were used simultaneously so that detailed elemental analysis of bulk as well as of different size fractions could be performed. Accelerator based nuclear analytical techniques such as Particle Induced X-Ray Emission (PIXE), Rutherford Backscattering (RBS) and Nuclear Microscopy (NM) were used for analysis. These techniques are fast, truly multielemental and perfectly suited for routine analysis of a large number of aerosol samples. Typically all samples were analysed for the following 24 elements: Na, Mg, Al, Si, P, S, Cl, K, Ca, Ti, V, Mn, Cr, Fe, Co, Ni, Cu, Zn, Ga, As, Br, Rb, Sr and Pb. Detection limits for bulk analysis were generally below ng/m3 and for single particle analysis absolute detectable mass was approximately 10-17 g. Additionally, trace elements such as Cd, Sn, Sb and Ba whose characteristic X-ray lines were normally "obscured" by the lines of other more abundant elements, were detected when analysing by nuclear microscope in single particle mode.Judging by the average concentrations of lead and sulphur which are good indicators of industrial component of air pollution the situation in Singapore is satisfactory. Pb was typically found in concentrations of 5 to 50 ng/m3 and sulphur in concentrations of 1 to 2 µg/m3. These concentrations are well below limits set by the World Health Organisation (1500 ng/m3 and 40 µg/m3, respectively). On the other hand during the haze period the average concentrations of elements like S, K, Ti, V, Mn, Ni, As and Pb were found to be 3 to 6 times higher than usual. Results are presented and discussed.     

The efficacy of protoporphyrin as a predictive biomarker for lead exposure in canvasback ducks: Effect of sample storage time

We used 363 blood samples collected from wild canvasback dueks (Aythya valisineria) at Catahoula Lake, Louisiana, U.S.A. to evaluate the effect of sample storage time on the efficacy of erythrocytic protoporphyrin as an indicator of lead exposure. The protoporphyrin concentration of each sample was determined by hematofluorometry within 5 min of blood collection and after refrigeration at 4 °C for 24 and 48 h. All samples were analyzed for lead by atomic absorption spectrophotometry. Based on a blood lead concentration of 0.2 ppm wet weight as positive evidence for lead exposure, the protoporphyrin technique resulted in overall error rates of 29%, 20%, and 19% and false negative error rates of 47%, 29% and 25% when hematofluorometric determinations were made on blood at 5 min, 24 h, and 48 h, respectively. False positive error rates were less than 10% for all three measurement times. The accuracy of the 24-h erythrocytic protoporphyrin classification of blood samples as positive or negative for lead exposure was significantly greater than the 5-min classification, but no improvement in accuracy was gained when samples were tested at 48 h. The false negative errors were probably due, at least in part, to the lag time between lead exposure and the increase of blood protoporphyrin concentrations. False negatives resulted in an underestimation of the true number of canvasbacks exposed to lead, indicating that hematofluorometry provides a conservative estimate of lead exposure.The U.S. Government's right to retain a non-exclusive, royalty-free licence in and to any copyright is acknowledgedDeceased     

Speciation of arsenic using solid phase extraction cartridges

Various solid phase extraction (SPE) cartridges were investigated for speciation of arsenite [As(III)], arsenate [As(v)], monomethylarsonic acid (MMA) and dimethylarsinic acid (DMA). Cartridges containing different types of sorbent materials were tested for arsenic retention and elution characteristics. Alumina cartridges were found to completely retain all the four target arsenic species, and are suitable for removal and preconcentration purposes. For speciation analysis, different arsenic species were separated on the basis of their selective retention on and elution from specific cartridges. DMA was retained on a resin-based strong cation exchange cartridge and eluted with 1.0 M HCl. MMA and As(v) were both retained on a silica-based strong anion exchange cartridge and sequentially eluted with 60 mM acetic acid (for MMA) and 1.0 M HCl [for As(v)]. As(III) was not retained on either cartridge and remained in solution. Arsenic species in solution and those eluted from the cartridges were subsequently quantified by using flow injection with hydride generation atomic fluorescence spectrometry (FI-HGAFS) and hydride generation atomic absorption spectrometry (FI-HGAAS). A detection limit of 0.05 microg L(-1) arsenic in water sample was achieved using HGAFS. An application of the method was demonstrated at a drinking water treatment facility. As(III) and As(v) species were determined in water at various stages of treatment. The method is suitable for routine determination of trace levels of arsenic in drinking water to comply with more stringent environmental regulations.     

Multi-objective, decision-based assessment of a water quality monitoring network in a river system

Water quality monitoring network design has historically tended to use experience, intuition and subjective judgement in locating monitoring stations. Better design procedures to optimize monitoring systems need to simultaneously identify significant planning objectives and consider a number of social, economic and environmental constraints. The consideration of multiple objectives may require further decision analysis to determine the preference weights associated with the objectives to aid in the decision-making process. This may require the application of an optimization study to extract such information from decision makers or experts and to evaluate the overall effectiveness of locating strategies. This paper assesses the optimal expansion and relocation strategies of a water quality monitoring network using a two-stage analysis. The first stage focuses on the information retrieval of preference weights with respect to the designated planning objectives. With the aid of a pre-emptive goal programming model, data analysis is applied to obtain the essential information from the questionnaire outputs. The second stage then utilizes a weighted multi-objective optimization approach to search for the optimal locating strategies of the monitoring stations in the river basin. Practical implementation is illustrated by a case study in the Kao-Ping River Basin, south Taiwan.     

Optimal and suboptimal control of anaerobic digesters

Anaerobic digester failure due to entry of inhibitors or sudden changes in the feed substrate concentration may be encompassed beneficially by applying optimal control theory. An almost proportional relationship between the dilution rate and the methane production rate leads to a simple suboptimal control law with only minor loss in performance, after the occurrence of the above mentioned events.     

Impact of distillery effluent application to land on soil microflora

A pot culture experiment was conducted to evaluate the effect of different treatments of distillery wastewater, i.e. raw, treated, diluted and raw distillery wastewater mixed with domestic waste stabilization pond effluent (1:1) on populations of bacteria, fungi, actinomycetes and nitrogen fixing bacteria. The results indicated that raw wastewater decreased the population of bacteria, fungi and actinomycetes. The growth rates of Rhizobium and Azotobacter were also reduced after raw wastewater application. The toxic effect of raw wastewater was minimized when it was mixed with stabilization pond effluent (1:1), this was demonstrated by an increase in the populations of all the microorganisms studied. When a groundnut plant was irrigated with raw distillery wastewater, no fruits were produced and there was also less nodulation. This study indicates that raw distillery wastewater is very toxic to the soil microorganisms which are important in the soil ecosystem.     

Quantification of protein adducts of hexahydrophthalic anhydride and methylhexahydrophthalic anhydride in human plasma

Hexahydrophthalic anhydride (HHPA) and methylhexahydrophthalic anhydride (MHHPA) are two highly allergenic compounds used in the chemical industry. A method was developed for quantification of protein adducts of HHPA and MHHPA in human plasma. The plasma was dialysed and the anhydrides were hydrolysed from the proteins at mild acidic conditions. The released hexahydrophthalic acid (HHP acid) and methylhexahydrophthalic acid (MHHP acid) were purified by reversed solid phase extraction followed by derivatisation with pentafluorobenzyl bromide. The derivatives were analysed using GC-MS in negative ion chemical ionisation mode with ammonia as moderating gas. As internal standards, deuterium labelled HHP and MHHP acids were used. The detection limits were 0.06 pmol mL(-1) plasma for HHP acid and 0.03 pmol mL(-1) plasma for MHHP acid. The between-day precisions for HHP acid were 18% at 0.3 pmol mL(-1) and 8% at 4 pmol mL(-1). For MHHP acid, the precisions were 13% at 0.3 pmol mL(-1) and 9% at 4 pmol mL(-1). There were strong correlations (r=0.94 for HHPA and 0.99 for MHHPA) between total plasma protein adduct concentrations and serum albumin adduct levels. Workers exposed to time-weighted average air levels of HHPA between < 1 and 340 microg m(-3) and between 2 and 160 microg m(-3) for MHHPA had plasma adduct levels between the detection limits of the methods and 8.40 and 19.0 pmol mL(-1), respectively.     

The influence of geometry and draught shields on the performance of passive samplers

Passive samplers provide an excellent opportunity to perform indicative measurements or establish a dense network of measuring sites. A drawback compared with conventional active measuring methods is the larger spread of results. This variation can, to a large extent, be attributed to the influence of temperature, sampler geometry and wind on sampling results. A proper design of sampler geometry and optimum choice of draught shield can reduce the influence of wind velocity on a badge type sampler to less than 10%. Wire mesh screens prove to be inadequate in damping turbulence. Filters give good results. Attention should be paid to the size and isolation value of the walls of the sampler to prevent thermal updrafts occurring within the sampler. Tube type samplers are less influenced by wind, provided that turbulence is prevented from influencing diffusion within the sampler.