TiO2胶体光催化降解罗丹明B染料

TiO2胶体从钛氧有机物水解制备,表征的方法有:X射线衍射光谱(XRD)、激光散射粒径分布、傅立叶变换红外光谱(FT-IR)、X射线光电子谱(XPS)和透射电子显微镜(TEM)。利用罗丹明B染料分子作为探针分子研究TiO2胶体的光催化活性,分析了pH、催化剂用量、外加氧化剂(H2O2)用量及罗丹明B初始浓度对TiO2胶体光催化活性的影响。结果表明:制备的TiO2胶体粒子平均粒径为13.8 nm(激光散法测定),光催化降解罗丹明B染料的反应属于一级动力学反应,可以用Langmuir-Hinshewood模型加以描述,反应速率常数k1为0.08413 mg/(L.min),平衡吸附常数k2为1.5305 L/mg;在pH为6,TiO2胶体用量为0.04%,H2O2(含量30%)用量为0.2%(V/V),光照度为69.6μW/cm2时,5 h后罗丹明B染料的降解率可达到99%以上;相似的条件,0.2%的P25 TiO2粉体光催化处理染料水时,罗丹明B的降解率为90%。纳米TiO2胶体不仅可以提高罗丹明B的光催化降解率,还具有用量少,可有效降低水处理成本的特点。     

改性甘蔗渣对Cu2+和Zn2+的吸附机理

研究了均苯四甲酸二酐(PMDA)和乙二胺四乙酸二酐(EDTAD)改性甘蔗渣对重金属离子Cu2+和Zn2+的吸附性能,包括吸附动力学和吸附等温线。结果表明,改性后的甘蔗渣对重金属离子Cu2+和Zn2+的吸附容量有显著提高,对Cu2+和Zn2+吸附等温线均符合Langmuir方程,吸附为单分子层吸附。根据Langmuir方程,PMDA和EDTAD改性甘蔗渣对Cu2+的吸附量分别为60.21和33.45 mg/g,对Zn2+的吸附量分别是70.53和36.53 mg/g。两种改性甘蔗渣对两种金属离子的吸附在30 min内均可完成,用准二级吸附动力学方程模拟动力学过程得到较好的线性相关性。以EDTA溶液为洗脱剂对吸附Cu2+和Zn2+的改性甘蔗渣进行洗脱再生,再生的吸附剂可反复使用。     

A simple method to prepare magnetic modified beer yeast and its application for cationic dye adsorption

The purpose of this research is to use a simple method to prepare magnetic modified biomass with good adsorption performances for cationic ions. The magnetic modified biomass was prepared by two steps: (1) preparation of pyromellitic dianhydride (PMDA) modified biomass in N, N-dimethylacetamide solution and (2) preparation of magnetic PMDA modified biomass by a situ co-precipitation method under the assistance of ultrasound irradiation in ammonia water. The adsorption potential of the as-prepared magnetic modified biomass was analyzed by using cationic dyes: methylene blue and basic magenta as model dyes. Optical micrograph and x-ray diffraction analyses showed that Fe₃O₄ particles were precipitated on the modified biomass surface. The as-prepared biosorbent could be recycled easily by using an applied magnetic field. Titration analysis showed that the total concentration of the functional groups on the magnetic PMDA modified biomass was calculated to be 0.75 mmol g^?1 by using the first derivative method. The adsorption capacities (q _m) of the magnetic PMDA modified biomass for methylene blue and basic magenta were 609.0 and 520.9 mg g^?1, respectively, according to the Langmuir equation. Kinetics experiment showed that adsorption could be completed within 150 min for both dyes. The desorption experiment showed that the magnetic sorbent could be used repeatedly after regeneration. The as-prepared magnetic modified sorbent had a potential in the dyeing industry wastewater treatment.     

长柄扁桃核壳活性炭的制备及表征

以长柄扁桃核壳为原料采用磷酸活化法制备活性炭,分别研究了温度、时间、浸渍比和磷酸浓度对活性炭吸附性能的影响;进而采用氮气吸附曲线和SEM对最佳工艺条件下的活性炭进行了表征。结果表明,长柄扁桃核壳是一种优质的活性炭原料;当温度为400℃,活化时间2 h,浸渍比2：1,磷酸浓度60%时,得到产率为46.46%,碘吸附值和亚甲基蓝吸附值分别为1 073 mg/g、255 mg/g,比表面积高达1 740 m²/g,中孔率为73.12%的孔隙发达的高中孔率活性炭。     

Biosorption and biodegradation of Acid Orange 7 by Enterococcus faecalis strain ZL: optimization by response surface methodological approach

Reactive dyes account for one of the major sources of dye wastes in textile effluent. In this study, decolorization of the monoazo dye, Acid Orange 7 (AO7) by the Enterococcus faecalis strain ZL that isolated from a palm oil mill effluent treatment plant has been investigated. Decolorization efficiency of azo dye is greatly affected by the types of nutrients and the size of inoculum used. In this work, one-factor-at-a-time (method and response surface methodology (RSM) was applied to optimize these operational factors and also to study the combined interaction between them. Analysis of AO7 decolorization was done using Fourier transform infrared (FTIR) spectroscopy, desorption study, UV–Vis spectral analysis, field emission scanning electron microscopy (FESEM), and high performance liquid chromatography (HPLC). The optimum condition via RSM for the color removal of AO7 was found to be as follows: yeast extract, 0.1 %?w/v, glycerol concentration of 0.1 %?v/v, and inoculum density of 2.5 %?v/v at initial dye concentration of 100 mg/L at 37 °C. Decolorization efficiency of 98 % was achieved in only 5 h. The kinetic of AO7 decolorization was found to be first order with respect to dye concentration with a k value of 0.87/h. FTIR, desorption study, UV–Vis spectral analysis, FESEM, and HPLC findings indicated that the decolorization of AO7 was mainly due to the biosorption as well as biodegradation of the bacterial cells. In addition, HPLC analyses also showed the formation of sulfanilic acid as a possible degradation product of AO7 under facultative anaerobic condition. This study explored the ability of E. faecalis strain ZL in decolorizing AO7 by biosorption as well as biodegradation process.     

Characterization of PM10 atmospheric aerosol at urban and urban background sites in Fuzhou city, China

Background

PM₁₀ aerosol samples were simultaneously collected at two urban and one urban background sites in Fuzhou city during two sampling campaigns in summer and winter. PM₁₀ mass concentrations and chemical compositions were determined.

Methods

Water-soluble inorganic ions (Cl^?, NO ₃ ^? , SO ₄ ^2? , NH ₄ ⁺ , K⁺, Na⁺, Ca²⁺, and Mg²⁺), carbonaceous species (elemental carbon and organic carbon), and elements (Al, Si, Mg, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, As, Se, Br, and Pb) were detected using ion chromatography, thermal/optical reflectance, and proton-induced X-ray emission methods, respectively.

Results

PM₁₀ mass concentrations, as well as most of the chemical components, were significantly increased from urban background to urban sites, which were due to enhanced anthropogenic activities in urban areas. Elements, carbonaceous species, and most of the ions were more uniformly distributed at different types of sites in winter, whereas secondary ion SO ₄ ^2? , NO ₃ ^? , and NH ₄ ⁺ showed more evident urban-background contrast in this season. The chemical mass closure indicated that mineral dust, organic matters, and sulfate were the most abundant components in PM₁₀. The sum of individually measured components accounted for 86.9?C97.7% of the total measured PM₁₀ concentration, and the discrepancy was larger in urban area than in urban background area.

Conclusion

According to the principal component analysis?Cmultivariate linear regression model, mineral dust, secondary inorganic ions, sea salt, and motor vehicle were mainly responsible for the PM₁₀ particles in Fuzhou atmosphere, and contributed 19.9%, 53.3%, 21.3%, and 5.5% of PM₁₀, respectively.     

湖北省咸宁市光伏电站太阳能资源评价

为了对无太阳辐射观测的咸宁市进行并网光伏电站太阳能资源综合评价,拟采用水平面太阳辐射气候学推算方法和倾斜面辐射换算方法,即根据武汉站历史资料分月建立总辐射量和直接辐射量与日照百分率的推算方程推算出咸宁逐月太阳辐射各分量,分析其时间变化、资源丰度和稳定性,并基于Klein提出的散射辐射各向同性的假设,计算出该地不同倾斜面年总辐射量和最佳倾角。结果表明：咸宁地区近50 a（1961~2009年）水平面太阳总辐射年总量为4 0914 MJ/m2,该地区属于太阳能资源丰富区,该地辐射形式等级处于散射辐射较多(C)等级,且太阳能资源年变化稳定度较高。正南朝向斜面接受总辐射年总量最大的条件下其最佳倾角为18°,该倾角下斜面年总辐射量为4 2246 MJ/m2,比水平的值高出33%。设计容量为1 500 kWp的光伏阵列若按最佳倾角和方位角安装,每年可发电约132×106 kW·h。太阳辐射各分量的合理推算与多个评价指标的联合应用为光伏电站规划设计提供了科学依据,也为今后类似工作提供了样本。     

Influence of ozone pollution and climate variability on net primary productivity and carbon storage in China's grassland ecosystems from 1961 to 2000

Our simulations with the Dynamic Land Ecosystem Model (DLEM) indicate that the combined effect of ozone, climate, carbon dioxide and land use have caused China's grasslands to act as a weak carbon sink during 1961-2000. This combined effect on national grassland net primary productivity (NPP) and carbon storage was small, but changes in annual NPP and total carbon storage across China's grasslands showed substantial spatial variation, with the maximum total carbon uptake reduction of more than 400gm(-2) in some places of northeastern China. The grasslands in the central northeastern China were more sensitive and vulnerable to elevated ozone pollution than other regions. The combined effect excluding ozone could potentially lead to an increase of 14Tg C in annual NPP and 0.11Pg C in total carbon storage for the same time period. This implies that improvement in air quality could significantly increase productivity and carbon storage in China's grassland ecosystems.     

Destruction of PCDD/Fs by SCR from flue gases of municipal waste incinerator and metal smelting plant

Partitioning of PCDD/F congeners between vapor/solid phases and removal and destruction efficiencies achieved with selective catalytic reduction (SCR) system for PCDD/Fs at an existing municipal waste incinerator (MWI) and metal smelting plant (MSP) in Taiwan are evaluated via stack sampling and analysis. The MWI investigated is equipped with electrostatic precipitators (EP, operating temperature: 230 degrees C), wet scrubbers (WS, operating temperature: 70 degrees C) and SCR (operating temperature: 220 degrees C) as major air pollution control devices (APCDs). PCDD/F concentration measured at stack gas of the MWI investigated is 0.728 ng-TEQ/Nm(3). The removal efficiency of WS+SCR system for PCDD/Fs reaches 93% in the MWI investigated. The MSP investigated is equipped with EP (operating temperature: 240 degrees C) and SCR (operating temperature: 290 degrees C) as APCDs. The flue gas sampling results also indicate that PCDD/F concentration treated with SCR is 1.35 ng-TEQ/Nm(3). The SCR system adopted in MSP can remove 52.3% PCDD/Fs from flue gases (SCR operating temperature: 290 degrees C, Gas flow rate: 660 kN m(3)/h). In addition, the distributions of PCDD/F congeners observed in the flue gases of the MWI and MSP investigated are significantly different. This study also indicates that the PCDD/F congeners measured in the flue gases of those two facilities are mostly distributed in vapor phase prior to the SCR system and shift to solid phase (vapor-phase PCDD/Fs are effectively decomposed) after being treated with catalyst. Besides, the results also indicate that with SCR highly chlorinated PCDD/F congeners can be transformed to lowly chlorinated PCDD/F congeners probably by dechlorination, while the removal efficiencies of vapor-phase PCDD/Fs increase with increasing chlorination.     

大气污染物扩散模式的应用研究综述

应用大气污染物扩散模式可以模拟不同尺度、气象、地形条件下工业污染物在大气中的输送与扩散特征,为大气监测、城市环境规划和空气质量预报等工作提供科学依据.归纳了目前广泛应用于模拟工业污染物扩散的模式,着重介绍了近年来国内外对这些模式的主要应用研究进展,比较了各模式在应用上的优缺点,并对大气污染物扩散模式的应用研究前景进行了讨论.