Efficient search procedures for extreme pollutant values

Extreme pollutant values are of great interest in water quality monitoring because of their frequent toxicological significance. The principal barrier to the detection of these values, however, is the cost of extensive and comprehensive monitoring. This paper demonstrates an efficient method to determine the maximum sample measurement from a finite set of sequential samples without explicitly testing them all. It is assumed that the process of sample measurement is distinct from collection and has higher costs. It is further assumed that the measurements have high positive autocorrelation.A methodology is presented based on a common industrial testing procedure referred to as composite sampling—the physical pooling or compositing of a set of sequential samples before measurement. A method known as primary first order compositing (PFOC) was found to be superior to the traditional technique of random sampling, particularly if small composite sizes are utilized.The authors are, respectively, operations research analyst, Vancouver, B. C.; Associate Professor and Chairman, Policy Analysis Division, Faculty of Commerce and Business Administration, University of British Columbia; and Associate Professor, Management Science Division, Faculty of Commerce, U.B.C.     

Determination of biomass burning emission factors: Methods and results

Biomass burning, in a broad sense, encompasses different burning practices, including open and confined burnings, and different types of vegetation. Emission factors of gaseous or particulate trace compounds are directly dependent both on the fuel type and the combustion process. Emission factors are generally calculated by stoichiometric considerations using the carbon mass balance method, applied either to combustion chamber experiments or to field experiments based on ground-level measurements or aircraft sampling in smoke plumes. There have been a number of experimental studies in the last 10 years to investigate wildfires in tropical, temperate, or boreal regions. This article presents an overview of measurement methods and experimental data on emission factors of reactive or radiatively active trace compounds, including trace gases and particles. It focuses on fires in tropical regions, that is, forest and savanna fires, agricultural burns, charcoal production, use of fuelwood, and charcoal combustion.     

Factor analysis of trace-element data from tree-bark samples in The Netherlands

Monte Carlo-assisted factor analysis has been applied to a data set of 20 trace-element concentrations in tree-bark samples obtained from 123 locations in The Netherlands, with the aim to investigate the suitability of bark as a biomonitor for air pollution. A Monte Carlo approach was used to give more insight to the uncertainties and significance levels of the factor analysis results. Notwith-standing a rather strong influence of soil material on the concentration levels, factor analysis enabled the identification of five significant pollution source types, all of which corresponded with source types found in an earlier biomonitoring study in The Netherlands using epiphytic lichens. A more detailed comparison with the lichen results showed a remarkable difference in lead concentrations between bark and lichen. It was concluded that bark can be successfully employed as a biomonitor for air pollution. The power of factor analysis to adequately determine the soil contribution may render extensive sample washing procedures superfluous.     

Evaluation of the Industrial Source Complex short-term model in a large-scale multiple source region for different stability classes

The original Industrial Source Complex Model (ISCST, 90346) and its latest version, the ISCST2 (92090), are evaluated for the 1- and 24-hour averaging periods, using six statistical parameters. The confidence limits on two parameters were obtained using the bootstrap, jacknife, seductive, and robust resampling techniques. Evaluation is conducted in a multiple point source environment and in all the different stability categories, using a year of meteorological data, emission inventory of the Lucas County, in Toledo, Ohio, and monitoring data from two nearby stations for the year 1987. This was representative of a real time situation in which the ISCST is generally applied for regulatory work. The sensitivity analysis shows that the ISC is a poor performing model in the 1-h and 24-h averaging period, neutral and stable categories, and modifications to it are necessary in order to improve its performance. Its performance changes depending on the chosen paired values. A better relative performance is observed in the unstable category relative to the neutral and stable categories. Improved model performance may be achieved by applying modifications to the physics on which the model is based.     

Heavy metals in the SPM of air in the environment surrounding a ferro-alloy industrial plant in India

Prices for ferro-alloys have hardened due to the closure of plants in developed countries on account of increasingly stringent pollution control legislation, resulting in a higher cost of production. A ferro-alloy industry with a capacity of 80000 MT per annum was selected to study the nature of pollution. Because of the objectionable nature of polluting air in and around the plant it was located in a rural area where there was no other industry. The area was agriculturally active and there was no effective control system for this plant.The quality of ambient air around the plant site is discussed in this paper along with the meteorological conditions. The maximum concentration of suspended particulate matter (SPM) was 768 µg/NM³ downwind of the plant, minimum 184 µg/NM³, and the average was more than 446 µg/NM³. The presence of heavy metals, viz. Fe, Mn, Cr and Pb, was also assessed. The concentration of Fe was 50 µg/NM³ downwind and 10 µg/NM³ upwind. The concentration of other metals followed a similar trend.     

Multimedia environmental monitoring: 50 years at Hanford

Environmental monitoring has been an ongoing activity on the U.S. Department of Energy's Hanford Site in southeastern Washington for almost 50 years. Objectives are to detect and assess potential impacts of Site operations on air, surface and ground waters, foodstuffs, fish, wildlife, soil and vegetation. Data from monitoring effects are used to calculate the overall radiological dose to humans working onsite or residing in nearby communities. In 1989, measured Hanford Site perimeter concentrations of airborne radionuclides were below applicable guidelines. Concentrations of radionuclides and nonradiological water quality in the Columbia River were in compliance with applicable standards. Foodstuffs irrigated with river water taken downstream of the Site showed radionuclide levels that were similar to those found in foodstuffs from control areas. Low levels of ¹³⁷Cs and ⁹⁰Sr in most onsite wildlife samples and concentrations of radionuclides in soils and vegetation from on- and offsite locations were typical of those attributable to worldwide fallout. The calculated dose potentially received by a maximally exposed individual (i.e., based on hypothetical, worst-case assumptions for all routes of exposure) in 1989 (0.05 mrem/yr) was similar to those calculated for 1985 through 1988.In addition to monitoring radioactivity in fish and wildlife, population numbers of key species are determined. Chinook salmon (Oncorhynchus tshawytscha) spawning in the Columbia River at Hanford has increased in recent years with a concomitant increase in winter roosting activity of bald eagles (Haliaeetus leucocephalus). An elk (Cervus elaphus) herd, established by immigration in 1972, is also increasing. The Hanford Site currently serves as a refuge for Canada goose (Branta canadensis), great blue heron (Ardea herodias), and various plants and other animals, e.g., mule deer (Odocoileus hemionus), and coyotes (Canis latrans).     

Fate and movement of atrazine, cyanazine, metolachlor and selected degradation products in water resources of the deep Loess Hills of Southwestern Iowa, USA

The environmental fate and movement of herbicides widely used for weed control in corn are assessed for a deep loess soil in southwestern Iowa. Beginning in the early 1980s, the herbicide-based weed control program emphasized the application of atrazine (ATR) or cyanazine (CYN) and metolachlor (MET) for both broadleaf and grass control. Between 1992 and 1995, concentrations of ATR, desethylatrazine (DEA), desisopropylatrazine (DIA), CYN and MET were measured in rainwater, both shallow and deep vadose zone water, and well water. Results show that the frequency of herbicide detections and the range and distribution of occurrences are dependent upon both landscape position and temporal inputs of recharge water from rainfall. Generally, DIA was observed more frequently and in higher mean concentration in well water than DEA, while DEA was observed more frequently than DIA in vadose zone groundwater. A chromatographic analogy is suggested to explain the occurrence patterns observed for both parent herbicide and degradation products within the unsaturated zone water. Analysis of rainwater samples collected during this time also revealed low concentrations of ATR, CYN and MET, with the timing of the detections indicative of non-local transport. Results show that the deep loess soil conducts both water and agricultural chemicals relatively rapidly and as such represents a production system which is vulnerable to contamination of shallow groundwater by herbicide-derived chemicals. Results also illustrate the importance of including major herbicide degradation products in water resource impact assessment studies.     

Background Levels of Metals in Soils, McMurdo Station, Antarctica

McMurdo Station is the largest research station in Antarctica, with a population that ranges each year from 250 to 1200 people. Because of its size and 40-year history of use, a number of locations around the station have become contaminated with wastes. Soils and sediments in these areas have been shown to contain elevated levels of petroleum-related products, PCBs, other organics, and metals. While some remedial investigations have been conducted, background levels of metals in soils have not been determined. This paper reports on background levels of metals in a natural basalt-derived soil (gray soil) and scoria (soft porous rock used as fill, red soil) near McMurdo Station using two fundamentally different analytical procedures, concentrated acid extraction/analysis and total metals. These data facilitate determining the extent and levels of metal contamination near McMurdo Station and provide reference levels of metals for comparison with existing and future remediation data. There were statistically significant differences between metals concentrations in both gray and red soils, and no correlations between the level of extracted versus total metal. Generally, only a small fraction of a metal was extractable.     

Fractionation of butyltin species during sample extraction and preparation for analysis

Solvent extraction and evaporative concentration steps are often used in procedures for the measurement of butyltins in environmental samples. As part of a larger study utilizing radiolabeled butyltins, the loss and fractionation of butyltins during sample preparation was investigated. TBT, DBT, and MBT were extracted from acidified seawater by hexane with efficiencies of about 95–99, 50–60 and 11% respectively. In addition, losses of about 70% of DBT were found during evaporative concentration of hexane. A variety of sediment extraction procedures were tested and none were found to be highly efficient for total butyltin extraction.