Emission Impacts of Electric Vehicles

Alternative vehicular fuels are proposed as a strategy to reduce urban air pollution. In this paper, we analyze the emission Impacts of electric vehicles In California for two target years, 1995 and 2010. We consider a range of assumptions regarding electricity consumption of electric vehicles, emission control technologies for power plants, and the mix of primary energy sources for electricity generation. We find that, relative to continued use of gasoline-powered vehicles, the use of electric vehicles would dramatically and unequivocally reduce carbon monoxide and hydrocarbons. Under most conditions, nitrogen oxide emissions would decrease moderately. Sulfur oxide and particulate emissions would Increase or slightly decrease. Because other areas of the United States tend to use more coal in electricity generation and have less stringent emission controls on power plants, electric vehicles may have less emission reduction benefits outside California.     

Speciation of Arsenic in Ambient Aerosols Collected in Los Angeles

First-time measurements of the potentially toxic inorganic species of arsenic (arsenite arid arsenate) have been obtained in fine (<2.5 µm AD) and coarse (>2.5 µm AD) atmospheric particles in the Los Angeles area. A recently developed method that includes procedures for sample collection, preparation, and analysis was used in this study. Size-fractlonated aerosol samples were collected with a high-volume dichotomous virtual impactor that employed polytetrafluoroethylene filters. Results were obtained for the recovery of arsenic standards added to unexposed and collected filters. Data from this study, indicated that the recently developed speciation method can be used to determine concentrations of As(lll) and As(V) In atmospheric particulate matter samples.

Size-fractionated aerosol samples were collected in the city of Industry during January and February 1987. In most samples, As(lll) and As( V) were above the detection limit (approximately 1 ng m^-3 of either species) in both aerosol size fractions. A greater portion (about 75 percent) of the two species were observed in the fine particles. The As(lll)/As(V) ratio for both particle sizes was close to 1 (I.e., an equal mixture of both species). Comparison of total suspended particulate arsenic measured by the speciation method to that measured by a routine California Air Resources Board-approved procedure showed good agreement (r = 0.94), indicating both methods were approximately equivalent for the collection and analysis of aerosol arsenic.     

HCI Sorption by Dry NaHCO3 for Incinerator Emissions Control

The sorption of hydrochloric acid (HCI) by thermally decomposed sodium bicarbonate (NaHCO₃) was investigated using a fixed-bed reactor containing sorbent particles dispersed in a bed of spherical glass beads. The gas flow rate (68° F and 760 mm Hg) was 0.039 cfm (1.1 liter/min) and the bed had a cross-sectional area of 0.0055 sq. ft. (5.1 sq. cm). The influence of particle diameter (10, 45 and 163 μm), temperature (225, 275, 375, 455, and 550° F), superficial gas velocity (11 and 21 fpm at reactor conditions, 375° F), and Inlet HCI gas concentration (415 ppm and 760 ppm in N₂, 275 and 455° F) were studied. Results showed that HCI sorption increased strongly with increasing temperature but was only weakly dependent on particle diameter, superficial gas velocity, and HCI gas concentration.     

A Combined Ca(OH)2/NH3 Flue Gas Desulfurization Process for High Sulfur Coal: Results of a Pilot Plant Study

The removal of SO₂ with atomization of a slaked lime slurry and supplemental injection of gaseous NH₃ were tested in a conventional spray dryer/baghouse system for SO₂ concentrations of 2000 ppm and 3000 ppm and a 30° F approach to saturation. Results at 3000 ppm of SO₂ showed an average SO₂ removal efficiency of 90.3 percent at a combined stoichiometric ratio of 0.95-1.10 and an average overall sorbent utilization of 91.6 percent. The overall molal ratio of NH₃/SO₂ reaction was found to be 2:1 under the test conditions Particle size analyses, and EP toxicity tests were conducted on the products of the reactions.     

The Effects of Infiltration and Insulation on the Source Strengths and Indoor Air Pollution from Combustion Space Heating Appliances

Many energy conservation strategies for residences involve reducing house air exchange rates. Reducing the air exchange rate of a house can cause an increase in pollutant levels if there is an indoor pollution source and if the indoor pollutant source strength remains constant. However, if the indoor pollutant source strength can also be reduced, then it is possible to maintain or even improve indoor air quality. Increasing the insulation level of a house is a means of achieving energy conservation goals and, in addition, can reduce the need for space heating and thereby reduce the pollutant source strengths of combustion space heaters such as unvented kerosene space heaters, unvented gas space heaters, and wood stoves. In this paper, the indoor air quality trade-off between reduced infiltration and increased insulation in residences is investigated for combustion space heaters. Two similar residences were used for the experiment. One residence was used as a control and the other residence had infiltration and insulation levels modified. An unvented propane space heater was used as the source in this study. A model was developed to describe the dependence of both indoor air pollution levels and the appliance source strengths on house air exchange rates and house insulation levels. Model parameters were estimated by applying regression techniques to the data. Results show that indoor air pollution levels in houses with indoor combustion space heating pollution sources can be held constant (or lowered) by reducing the thermal conductance by an amount proportional to (or greater than) the reduction of the air exchange rate.     

Limestone Dissolution in Flue Gas Scrubbing: Effect of Sulfite

Batch limestone dissolution experiments were carried out in a pH stat apparatus at 55°C with CO2 sparging and dissolved sulfite. Particle size distribution, utilization, sulfite in solution, limestone type, and the approach to calcite equilibrium were all found to contribute to the limestone reactivity. In the absence of sulfite, limestone dissolution was controlled solely by mass transfer. For a given stone under mass transfer control, film thickness was found to be independent of pH. The dissolution rate in the presence of sulfite was controlled by a combined surface kinetics/mass transfer regime. SEM micrographs supported this conclusion. A surface rate correlation was developed which accounted for observed inhibition by an inverse dependence on calcium sulfite concentration at the limestone surface. While the form of the rate expression was applicable to all stones, the surface rate constant was stone dependent. A computer code which accounted for mass transfer with surface kinetics was tested against experimental observations of four limestone types. Changes in pH and the concentrations of calcium, carbonate, sulfite, sulfate, and adipic acid were accurately modeled.     

Ozone Control Strategies Based on the Ratio of Volatile Organic Compounds to Nitrogen Oxides

The 1990 Clean Air Act Amendments require states with O₃ nonattainment areas to adopt regulations to enforce reasonable available control technologies (RACT) for NO_X stationary sources by November 1992. However, if the states can demonstrate that such measures will have an adverse effect on air quality, NO_X requirements may be waived. To assist the states in making this decision, the U.S. EPA is attempting to develop guidelines for the states to use in deciding whether NO_X reductions will have a positive or negative impact on O3 air quality. Although NO_X is a precursor of O₃, at low VOC/NO_X ratios, the reduction of NO_X can result in increased peak O₃. EPA is examining existing information on VOC/NO_X ratios to develop “rules of thumb” to guide the states in their decision-making process. An examination of 6 a.m. to 9 a.m. VOC/NO_X ratios at a number of sites in the eastern U.S. indicates that the ratio is highly variable from day-to-day and there is no apparent relationship between ratios measured at different sites within the same area. In addition, statistical analysis failed to identify significant relationships between the 6 a.m. to 9 a.m. VOC/NO_X ratio and the maximum 1-hr. O₃ within a given area. Since we know from smog chamber and modeling studies that such a relationship exists, this further invalidates the assumption that a ratio measured at a single site is representative of the ratio for the entire region. Based on this Information, we conclude that having the 6 a.m. to 9 a.m. ambient VOC/NO_X ratio for a given area is insufficient information, by itself, to decide whether a VOC-alone, a NO_x-alone, or a combined VOC-NO_X reduction strategy is a viable or optimum O₃-reduction strategy.     

Ambient Air Benzene Concentrations in Canada (1989-1993): Seasonal and Day of Week Variations,Trends, and Source Influences

Abstract

Since 1987, the Pollution Measurement Division of the Environmental Protection Service, Environment Canada, has operated a field program for measuring benzene in ambient air. With the cooperation of provincial and municipal environmental agencies, samples have been collected at over 30 urban and rural monitoring sites across the country. Samples are collected in evacuated canisters and analyzed by gas chromatography with a mass-selective detector. Using data from all sites, the composite average benzene concentration for Canada over the years 1989 to 1993 was 3.6 μg/m³ and the composite median was found to be 2.6 μ/m³. Benzene concentrations are highest at urban sites near major streets and at sites influenced by industrial sources. For eighteen urban and suburban trend sites (those with no nearby industrial sources), composite annual median benzene concentrations decreased by 20% between 1989 and 1993. For the same period, median benzene concentrations decreased by 33% at four trend sites with nearby industries. At most monitoring sites the parameters for benzene and CO are highly correlated; supporting the inventory estimate that most emissions of benzene are due to vehicle exhaust. For sites with nearby industrial sources of benzene, the industries are estimated to account for 35 to 70% of the benzene dose experienced at the sites. These site specific contributions are much more significant than the estimated national emissions assigned to industrial sources.     

Atmospheric Chemistry of Toxic Contaminants. 3. Unsaturated Aliphatics: Acrolein,Acrylonitrile, Maleic Anhydride

Detailed mechanisms are outlined for the chemical reactions that contribute to In-situ formation and atmospheric removal of the unsaturated aliphatic contaminants acrolein, acrylonitrile, and maleic anhydride. In-situ formation of small amounts of acrolein and maleic anhydride may Involve the reaction of OH (and O₃) with 1,3-dienes and the reaction of OH with aromatic hydrocarbons, respectively. There is no known pathway for In-situ formation of acrylonitrile. Rapid removal of acrolein (half-life = less than one day) and of maleic anhydride (half-life = several hours) is expected from their rapid reactions with OH (major), O₃, and NO₃. These reactions lead to formaldehyde and glyoxal from acrolein and to dicarbonyls from maleic anhydride. Acrylonitrile is removed at a slower rate (half-life = 2–7 days) by reaction with OH, leading to formaldehyde and formyl cyanide.