一种机(针)织物与非织造布网络互穿复合材料的研究

本文主要对机织物与非织造布复合材料的网络互穿结构进行了描述,并从材料选择、单体试制、复合工艺方面进行了实践,研制出了较高透气性能和剥离强度的复合材料。     

基于道化学法的大型合成氨装置安全评价

根据道化学公司火灾、爆炸危险指数的基本原理。用VH6．0开发的安全评价软件DowSE1．0，对某大型合成氨装置进行安全评价，得出其安全措施补偿前后的火灾、爆炸指数F＆EI以及危险暴露面积，危害系数，危险等级，实际可能财产损失程度等指数。结果表明。合成氨装置中实际最大可能财产损失值都没有超过200万美元，气化系统在合成氨装置中实际最大可能财产损失值占损失替换值比例高达53％，超过了10％的相对危险值界限。说明在引进国外技术时应注重其安全防范配套措施消化吸收，并结合实际采取切实可行的安全措施，降低合成氨装置的风险程度。     

不同比例乙酸和丙酸对活性污泥微生物合成聚羟基脂肪酸酯的影响

聚羟基脂肪酸酯（PHA）是一种生物可降解塑料,利用活性污泥合成PHA具有节约成本、操作方便的优点。研究选择污泥发酵液挥发性脂肪酸（VFAs）中比重相对较高的乙酸和丙酸作为碳源自配营养液,深入研究不同质量浓度比对PHA合成的影响。结果表明,乙酸为主要碳源时更有利于PHA的合成,最大合成量12.3%出现在乙酸作为唯一碳源的条件下。此外,PHA合成量随着底物中有机酸比重的增加而增加,充分展现了利用挥发性脂肪酸大量合成PHA的良好前景。     

铁阳极电凝聚处理活性黑KN-B染料废水

对铁阳极电凝聚处理活性黑KN-B染料废水过程进行了实验研究.考察了电流密度、染料溶液初始pH值、电介质浓度及种类、温度、染料浓度等因素对脱色效率的影响.结果表明,在一定实验条件下,活性黑KN-B模拟废水的脱色效率达93%;电流强度、染料浓度、电解液初始pH值及电解质的种类对染料溶液脱色效率影响显著,电解液温度、电解质的浓度对脱色效率的影响不明显;以铁为阳极的原位电凝聚处理活性黑KN-B模拟废水混凝过程中主要作用机理以吸附电性中和为主;电凝聚过程中活性黑KN-B在阴极上发生了还原反应.     

基于PIV技术的ABR反应器在不同HRT下的液相流态特性

利用激光粒子图像测速技术（PIV）对ABR反应器的液相流态进行了研究,在水力停留时间（HRT）为3~58 h变化时,测试得反应器内下流室和上流室折流板内外侧关键截面的流场数据,获得了相关流场特征,包括速度矢量图、流线图谱和涡量场等。结果表明,HRT对下流室和上流室的液相轴向、径向平均速度和平均涡量强度影响不同,液相回流面积随HRT的增加逐渐减小;下流室液相平均涡量强度随HRT的增加逐渐增加;上流室液相平均涡量强度随HRT的增加逐渐减小。下流室和上流室在特定HRT时产生涡流、沟流。在本实验条件下,当处理难降解或高浓度废水时,得出HRT为33 h时反应器整体流态最佳。     

低强度超声波预处理对污泥自热式高温好氧消化的影响

以0.3 W·cm-2的低强度超声波对调配好的污泥进行5、10和20 min的辐照,再经过12 d的自热式高温好氧消化（ATAD）。结果表明,适当的低强度超声预处理能够有效地加快稳定化进程,其中超声波辐照10 min后的实验组效果最好,在第8.5天时,温度升高至58.3℃,VSS去除率达到42.1%,比未经超声预处理的实验组提前2 d达到稳定状态。在消化过程中脱氢酶的活性与VSS去除率有着很好的相关性（R2>0.86）,它能有效地表征VSS的高温好氧降解规律及有机物去除程度。稳定后的污泥上清液中TP浓度降至初始浓度的40%以下,TOC浓度升高至初始浓度的3~4倍。然它们的浓度仍很高,仍会给后续处理增加一定的负担。     

Influence of hydrogeochemical processes on zero-valent iron reactive barrier performance: a field investigation

Geochemical and mineralogical changes were evaluated at a field Fe0-PRB at the Oak Ridge Y-12 site concerning operation performance during the treatment of U in high NO3- groundwater. In the 5-yr study period, the Fe0 remained reactive as shown in pore water monitoring data, where increases in pH and the removal of certain ionic species persisted. However, coring revealed varying degrees of cementation. After 3.8-yr treatment, porosity reduction of up to 41.7% was obtained from mineralogical analysis on core samples collected at the upgradient gravel-Fe0 interface. Elsewhere, Fe0 filings were loose with some cementation. Fe0 corrosion and pore volume reduction at this site are more severe due to the presence of NO3- at a high level. Tracer tests indicate that hydraulic performance deteriorated: the flow distribution was heterogeneous and under the influence of interfacial cementation a large portion of water was diverted around the Fe0 and transported outside the PRB. Based on the equilibrium reductions of NO3- and SO4(2-) by Fe0 and mineral precipitation, geochemical modeling predicted a maximum of 49% porosity loss for 5 yr of operation. Additionally, modeling showed a spatial distribution of mineral precipitate volumes, with the maximum advancing from the interface toward downgradient with time. This study suggests that water quality monitoring, coupled with hydraulic monitoring and geochemical modeling, can provide a low-cost method for assessing PRB performance.     

臭氧催化氧化工艺深度处理印染废水

采用正交实验对催化剂NiO/γ-A12O3的制备条件进行优化,并探讨臭氧催化氧化法对于印染废水的深度处理效能.结果表明,最优的催化剂制备条件为:浸渍液浓度为3％、浸渍时间为4h、灼烧温度为450℃、灼烧时间为3h.臭氧催化氧化反应15 min时,COD浓度由84.22 mg/L降低至50.00 mg/L以下;氨氮浓度由10.88 mg/L降低至5.01 mg/L;色度去除率达到69％,明显高于单纯臭氧氧化的反应效率.     

超滤膜深度处理染整废水的膜污染机理

实验采用不同规格和材料的超滤膜进行染整二级尾水分离实验,对超滤膜污染机理及影响因素进行了分析。实验采用红外光谱分析了聚醚(PES)膜、聚砜(PSF)膜和聚醚酰亚胺(PEI)膜3种超滤膜材料,对比了污染前后膜面的接触角以及不同切割分子量对膜通量及出水水质的影响,并利用线性化的Herman堵塞模型拟合了不同分子量超滤膜的堵塞模型,初步探讨了超滤膜的污染机理。实验结果表明,膜材料表面亲水性基团的多少与初始膜通量大小成正比,出水COD值随超滤膜切割分子量减小而减小。切割分子量同为2 000 Da的3种超滤膜中,PES膜的处理效果最佳,出水COD平均值为47.81 mg/L;PEI膜通量最高,平衡通量可达50 L/(m2.h);切割分子量为1 000、10 000的超滤膜堵塞机理符合滤饼过滤模型,100 000的超滤膜堵塞机理更接近于完全堵塞模型;1 000的聚醚砜材质膜(PES)更适合此类废水的深度处理。     

Quantitative evaluation of environmental risks of flotation tailings from hydrothermal sulfidation–flotation process

Floatation tailings (FT) are the main by-products of the hydrothermal sulfidation–flotation process. FT (FT₁ and FT₂) were obtained by treating two different neutralization sludges (NS) (NS₁ and NS₂). This paper quantitatively evaluated the environmental risks of heavy metals (Zn, Cd, Cu, Pb, and As) in FT versus NS. The total concentration and leaching rates (R ₂) of heavy metals in FT were much lower than those in NS, demonstrating that the hydrothermal sulfidation–flotation process was able to effectively suppress the mobility and leachability of heavy metals. The BCR-three sequence leaching procedure of FT confirmed that all metals were transformed into more stable forms (residue and oxidizable forms) than were found that in NS. The potential ecological risk index indicated that the overall risks caused by heavy metals decreased significantly from 6627.59 and 7229.67 (very serious risk) in NS₁ and NS₂, respectively, to 80.26 and 76.27 (low risk) in FT₁ and FT₂, respectively. According to the risk assessment code, none of the heavy metals in FT posed significant risk to the natural environment except Zn (with low risk). In general, the risk of heavy metals in FT had been well controlled.