Buchbesprechungen

The Science of Nature -     

将高纬度地区生态系统的反馈与恢复力引入公司决策

本文讨论了在高纬度地区公司所起的作用,它被概念化为以社会和经济为媒介的生态系统,同时指出了商业环境里其他的一些重要的社会参与者.我们列举了高纬地区企业行为的三个案例并对其中各种共性进行了讨论.特别的,我们认为有必要对商业理论和实践进行革新,以使其不只是停留在社会与经济概念的组织恢复力上,而要把高纬地区的生态恢复力也包括到商业管理的目标之中.同时我们也认为区域生态系统的恢复力应该成为衡量企业可持续管理的一个有意义的指标,企业高层可以据此制定和修改企业的管理策略.最后,文章在结尾处呼吁对高纬地区内的跨国公司和国内公司的作用制定更为详细的研究议程.     

Carbon mitigation potential and costs of forestry options in Brazil,China, India,Indonesia, Mexico,the Philippines and Tanzania

This paper summarizes studies of carbon (C) mitigation potential and costs of about 40 forestry options in seven developing countries. Each study uses the same methodological approach – Comprehensive Mitigation Assessment Process (COMAP) – to estimate the above parameters between 2000 and 2030. The approach requires the projection of baseline and mitigation land-use scenarios. Coupled with data on a per ha basis on C sequestration or avoidance, and costs and benefits, it allows the estimation of monetary benefit per Mg C, and the total costs and carbon potential. The results show that about half (3.0 Pg C) the cumulative mitigation potential of 6.2 Petagram (Pg) C between 2000 and 2030 in the seven countries (about 200× 10⁶ Mg C yr^-1) could be achieved at a negative cost and the remainder at costs ranging up to $100 Mg C^-1. About 5 Pg C could be achieved, at a cost less than $20 per Mg C. Negative cost potential indicates that non-carbon revenue is sufficient to offset direct costs of these options. The achievable potential is likely to be smaller, however, due to market, institutional, and sociocultural barriers that can delay or prevent the implementation of the analyzed options.     

镀液循环流量对封闭循环电沉积Ni-SiC复合镀层的影响

目的 研究封闭式镀液循环装置中不同镀液循环流量对Ni-SiC复合镀层的影响规律,优化镀液循环流量参数.方法 以Q235管状工件为待镀基体,以添加SiC颗粒的改良瓦特镀液为母液,在自主研发的封闭式镀液循环电镀装置中以0.3、0.5、0.7 m3/h的镀液循环流量于管件内壁制备Ni-SiC复合镀层,通过SEM检测、XRD测试、硬度测试和摩擦磨损性能测试等手段,对各Ni-SiC复合镀层宏微观形貌、厚度、成分、结构、硬度和耐磨性进行分析研究.结果 在0.5 m3/h流量条件下,镀层厚度为32.98μm,SiC颗粒含量为15.37％,镀层晶粒尺寸和硬度分别为10.84 nm和704HK0.245,该条件下制备的Ni-SiC复合镀层具有最佳耐磨性,摩擦系数为0.41,体积磨损率仅2.83×10–5 mm3/Nm.结论 在不同镀液循环流量参数下,采用该封闭式循环电镀装置,均可制得均匀完整的Ni-SiC复合镀层.随镀液循环流量的升高,镀层厚度和SiC颗粒体积含量均降低,镀层颜色金属光泽增强,镀层晶粒尺寸先减小、后增大,镀层硬度则先升高、后降低.