Co-injection of air and steam for the prevention of the downward migration of DNAPLs during steam enhanced extraction: an experimental evaluation of optimum injection ratio predictions

When steam is injected into soil containing a dense volatile non-aqueous phase liquid contaminant, the DNAPL vaporized within the heated soil region condenses and accumulates ahead of the steam condensation front. If enough DNAPL accumulates, gravitational forces can overcome trapping forces allowing the liquid contaminant to flow downward. By injecting air with steam, a portion of the DNAPL vapor remains suspended in equilibrium with the air, decreasing liquid contaminant accumulation ahead of the steam condensation front, and thus reducing the possibility of downward migration. In a previous work, a theoretical model was developed to predict the optimum injection ratio of air to steam that would eliminate accumulation of DNAPL ahead of the temperature front and thus minimize the potential for downward migration. In this work, the theoretical model is summarized, and an experiment is presented in order to evaluate the optimum injection ratio prediction. In the experiment, a two-dimensional water saturated sand pack is contaminated with a known mass of TCE (DNAPL). The system is then remediated by co-injecting air and steam at the predicted optimum injection ratio, calculated based on the average contaminant soil concentration in the sand pack. Results for the co-injection of air and steam are compared to results for the injection of pure steam or pure air. Injection at the predicted optimum injection ratio for a volumetric average NAPL saturation, reduced accumulation of the contaminant ahead of the condensation front by over 90%, as compared to steam injection alone. This indicates that the optimum injection ratio prediction is a valuable tool for limiting the spreading of DNAPL during steam-enhanced extraction. Injection at the optimum injection ratio resulted in earlier recovery of contaminant than for steam injection alone. Co-injection of steam and air is also shown to result in much higher recovery rates than air injection alone.     

Cytotoxicity and DNA damage of five organophosphorus pesticides mediated by oxidative stress in PC12 cells and protection by vitamin E

Previous studies have demonstrated that pesticides could induce cytotoxicity and genotoxicity in vivo and in vitro, and that oxidative stress may be an important factor involved. However, investigations comparing the capability of different organophosphorous (OP) compounds to induce cytotoxicity, genotoxicity and oxidative stress are limited. Hence, the aim of this paper was to access the cytotoxic and genotoxic effects of five OPs or metabolites, Acephate (ACE), Methamidophos (MET), Chloramidophos (CHL), Malathion (MAT) and Malaoxon (MAO), and to clarify the role of oxidative stress, using PC12 cells. The results demonstrated that MET, MAT and MAO caused significant inhibition of cell viability and increased DNA damage in PC12 cells at 40 mg L^?1. MAO was more toxic than the other OPs. ACE, MET, MAT and MAO increased the levels of intracellular reactive oxygen species (ROS) and malondialdehyde (MDA), and decreased the activity of superoxide dismutase (SOD), catalase (CAT) and glutathione (GSH) at 20 mg L^?1 and 40 mg L^?1 to different degrees. Pre-treatment with vitamin E(600 μM)caused a significant attenuation in the cytotoxic and genotoxic effect; pre-treatment reversed subsequent OP-induced elevation of peroxidation products and the decline of anti-oxidant enzyme activities. These results indicate that oxidative damage is likely to be an initiating event that contributes to the OP-induced cytotoxicity.     

Improvements of nano-SiO2 on sludge/fly ash mortar

Sewage sludge ash has been widely applied to cementitious materials. In this study, in order to determine effects of nano-SiO(2) additives on properties of sludge/fly ash mortar, different amounts of nano-SiO(2) were added to sludge/fly ash mortar specimens to investigate their physical properties and micro-structures. A water-binding ratio of 0.7 was assigned to the mix. Substitution amounts of 0%, 10%, 20%, and 30% of sludge/fly ash (1:1 ratio) were proposed. Moreover, 0%, 1%, 2%, and 3% of nano-SiO(2) was added to the mix. Tests, including SEM and compressive strength, were carried out on mortar specimens cured at 3, 7, and 28 days. Results showed that sludge/fly ash can make the crystals of cement hydration product finer. Moreover, crystals increased after nano-SiO(2) was added. Hence, nano-SiO(2) can improve the effects of sludge/fly ash on the hydration of mortar. Further, due to the low pozzolanic reaction active index of sludge ash, early compressive strengths of sludge/fly ash mortar were decreased. Yet, nano-SiO(2) could help produce hydration crystals, which implies that the addition of nano-SiO(2) to mortar can improve the influence of sludge/fly ash on the development of the early strength of the mortar.     

Simultaneous treatment of PVC and oyster-shell wastes by mechanochemical means

This work presents a new process for dechlorinating poly-vinyl chloride (PVC) by the use of oyster-shell waste. The process consists of milling of PVC waste with oyster-shell waste, followed by washing the milled sample with water. The milling of PVC and oyster-shell mixture results in size reduction and rupture in bonds, leading to mechanically induced reactions between the two to form CaCl2 and hydrocarbon with C=C bonds. Washing the milled mixtures with water at room temperature allows complete removal of chlorine from the milled sample. More than 95% of chlorine in PVC was removed when 2h grinding is conducted for the mixture. The present process could offer a potential route to the handling and disposal of oyster-shell and PVC wastes.     

Architects' perspectives on construction waste reduction by design

The construction, demolition and excavation waste arising in England was estimated at 91 million tonnes in 2003. The current thinking on construction waste minimisation is heavily focussed on several issues relating to physical construction waste and recycling guides. Indeed, much had been published on ways to improve on-site waste management and recycling activities but very few attempts made to address the effect of design practices on waste generation. However, there is a consensus in the literature that the architect has a decisive role to play in helping to reduce waste by focussing on designing out waste. This paper examines previous studies on architects' approach towards construction waste minimisation; and by means of a postal questionnaire, investigates: the origins of waste; waste minimisation design practices in the UK; and responsibilities and barriers within the UK architectural profession. The findings reveal that waste management is not a priority in the design process. Additionally, the architects seemed to take the view that waste is mainly produced during site operations and rarely generated during the design stages; however, about one-third of construction waste could essentially arise from design decisions. Results also indicate that a number of constraints, namely: lack of interest from clients; attitudes towards waste minimisation; and training all act as disincentives to a proactive and sustainable implementation of waste reduction strategies during the design process.     

Physical and chemical changes during composting of wood chip-bedded and straw-bedded beef cattle feedlot manure

In the 1990s, restrictions on incineration encouraged the forest industry in western Canada to develop new uses for their wood residuals by product. One such use was as a replacement for cereal straw bedding in southern Alberta's beef cattle (Bos taurus) feedlot industry. However, use of carbon (C)-rich bedding, such as wood chips, had implications for subsequent composting of the feedlot manure, a practice that was being increasingly adopted. In a 3-yr study, we compared composting of wood chip-bedded manure (WBM) and barley (Hordeum vulgare L.) straw-bedded manure (SBM). There were no significant differences in temperature regimes of SBM and WBM, indicating similar rates of successful composting. Of 17 physical and chemical parameters, five showed significant (P < 0.10) differences due to bedding at the outset of composting (Day 0), and 11 showed significant differences at final sampling (Day 124). During composting (10 sampling times), seven parameters showed significant bedding effects, 16 showed significant time effects, and four showed a Bedding x Time interaction. Significantly lower (P < 0.10) losses of nitrogen (N) occurred with WBM (19%) compared with SBM (34%), which has positive implications for air quality and use as a soil amendment. Other advantages of WBM compost included significantly higher total C (333 vs. 210 kg Mg(-1) for SBM) and inorganic N (1.3 vs. 1.0 kg Mg(-1) for SBM) and significantly lower total phosphorus (4.5 vs. 5.3 kg Mg(-1) for SBM). Our results showed that wood chip bedding should not be a problem for subsequent composting of the manure after pen cleaning. In combination with other benefits, our findings should encourage the adoption of wood chips over straw as a bedding choice for southern Alberta feedlots.     

Changing effluent chemistry affect survival,growth and physiological function of <Emphasis Type="Italic">Acacia nilotica</Emphasis> seedlings in northwestern region of India

Recycling and conservation efforts for water are the need of the day because of the lack of new water sources and the ever-increasing demand for drinking water. Seedlings of Acacia nilotica L. were irrigated with: canal water (T₁, control); municipal effluent (T₂); textile effluent (T₃); steel effluent (T₄); textile + municipal effluent in 1:1 ratio (T₅); steel + municipal effluent in 1:2 ratio (T₆); steel + textile in 1:2 ratio (T₈) and steel + municipal + textile in 1:2:2 ratio (T₇) with views to observe effluents effect on the seedlings and its adaptability and to recommend safe disposal of these effluents. Seedlings in T₆, T₇ and T₈ showed 50% lesser height and collar diameter than those in control. Seedlings in T₂ attained greatest height, collar diameter, numbers of branches and produced 140 g dry biomass seedling⁻¹. Highest concentration of manganese (Mn), iron (Fe), copper (Cu) and zinc (Zn) and lowest concentration of nitrogen (N), phosphorus (P), potassium (K), calcium (Ca) and magnesium (Mg) in the seedlings of T₄, T₆, T₇ and T₈ resulted in nutritional imbalance, mineral toxicity and reduction in photosynthetic (Pn) and transpiration (E) rates and caused seedling mortality. Seedlings of T₃ had highest sodium concentration and low concentration of Ca, Mg and micronutrients resulting in nutritional imbalance, augmented chlorosis and reduced gas exchange and biomass by half as compared to control. Increased growth, Pn and E and biomass in seedlings of T₅ over T₃ and survival period in T₆, T₇ and T₈ seedlings suggested a beneficial effect of effluents mixing. Unscientific disposal should be avoided and toxic concentration of metal ions␣may be reduced for long-term application and harmless disposal of effluents in afforestation and urban development.     

In situ transmissiometer measurements for real-time monitoring of dust discharge during orchard nut harvesting

Rapid assessments of operating conditions and field preparation on dust discharge from nut harvesters are needed to guide improved equipment design and grower practices for dust reduction. An industrial opacity sensor, typically used for industrial stack monitoring, was adapted for use on a nut harvester to measure relative dust intensity during nut pick-up operations in almond orchards. Due to the high volume of discharge air and the presence of large debris such as leaves, additional components were coupled with the sensor to enable subsampling of the air. Pre-harvest windrow preparation conditions were evaluated. Results indicated that relative dust intensity decreased by 32% during harvest activities after windrow preparation with proper nut sweeper adjustment. Conventional harvesting results indicated that under typical operating conditions, reducing the separation fan speed could reduce relative dust intensity by 54%. Ground speed also had a strong effect; reducing speed from 4.8 to 2.4 km h(-1) reduced opacity of discharged air by 50%. The measurement system was also mounted on a separate vehicle and used as a tool for comparing modifications in harvest machine designs where direct measurement of discharge may not be feasible due to mechanical constraints. A comparison between a conventional harvester and one modification in the harvester design found that the machine modification decreased relative dust intensity by 73%. The measurement tools described in this work can be used to provide rapid feedback on harvester operating conditions, orchard cultural practices, and machine design modifications.     

Assessment of <Emphasis Type="Italic">Gmelina arborea</Emphasis> sawdust–cement-bonded rainwater storage tank

The performance of a mixture of a forest bye product and cement for the production of storage structure for harvested rainwater was assessed. Three mix ratios of Cement: Gmelina arborea sawdust 3.0:1.0 (specimen A), 2.5:1.0 (specimen B) and 2.0:1.0 (specimen C) were considered. Engineering properties and dimensional stability of the different mix-ratios were monitored from prototypes cylindrical pots and test billet specimens. Possible change in quality of stored rainwater, with time was monitored in all the three cases. Water quality parameters monitored include pH, hardness, total suspended solids, alkalinity, acidity and total dissolved CO₂. The tensile stress obtained were 110, 104, and 95 N/mm², while the compressive strength were 5,000, 3,000, and 2,000 kN for specimens A, B and C respectively. Accelerated aging test showed that sample A were more resistant to deformation, while specimen C were more susceptible to change in structure over time. Similarly, the values of tensile and compressive strength after accelerated aging test increased in the order of specimen A > B > C. Except in specimen C where significant differences in alkalinity and acidity were observed, there were no significant differences in quality of the water stored in the pots after 2 months of storage. The results indicate the suitability of the Gmelina arborea waste as an alternative in constructing water storage structures in rural communities.     

The Coachella Valley Multiple Species Habitat Conservation Plan: A Decade of Delays

This article describes the history of the Coachella Valley Multiple Species Habitat Conservation Plan (CVMSHCP), in the Riverside County region of Southern California. When this collaborative biodiversity conservation planning process began, in 1994, local participants and supporters had numerous factors working in their favor. Yet, as of April 2007, nearly 13 years had passed without an approved plan. This is a common problem. Many multiple species habitat conservation plans now take more than a decade to complete, and the long duration of these processes often results in negative consequences. The CVMSHCP process became bogged down—despite strong scientific input and many political advantages—due to problematic relationships between the Plan’s local supporters, its municipal signatory parties, and officials from the state and federal wildlife agencies, particularly the regional office of the US Fish and Wildlife Service. This case study demonstrates the crucial importance of institutional structures and relationships, process management, and timeliness in habitat conservation planning. We conclude by offering several related recommendations for future HCP processes.