Significance of design and operational variables in chemical phosphorus removal

Batch and continuous experiments using model and real wastewaters were conducted to investigate the effect of metal salt (ferric and alum) addition in wastewater treatment and the corresponding phosphate removal from a design and operational perspective. Key factors expected to influence the phosphorus removal efficiency, such as pH, alkalinity, metal dose, metal type, initial and residual phosphate concentration, mixing, reaction time, age of flocs, and organic content of wastewater, were investigated. The lowest achievable concentration of orthophosphate under optimal conditions (0.01 to 0.05 mg/L) was similar for both aluminum and iron salts, with a broad optimum pH range of 5.0 to 7.0. Thus, in the typical operating range of wastewater treatment plants, pH is not a sensitive indicator of phosphorus removal efficiency. The most significant effect for engineering practice, apart from the metal dose, is that of mixing intensity and slow kinetic removal of phosphorus in contact with the chemical sludge formed. Experiments show that significant savings in chemical cost could be achieved by vigorously mixing the added chemical at the point of dosage and, if conditions allow, providing a longer contact time between the metal hydroxide flocs and the phosphate content of the wastewater. These conditions promoted the achievement of less than 0.1 mg/L residual orthophosphate content, even at lower metal-to-phosphorus molar ratios. These observations are consistent with the surface complexation model presented in a companion paper (Smith et al., 2008).     

Biocompatible Polyurethane Scaffolds Prepared from Glycerol Monostearate-Derived Polyester Polyol

Biodegradable polyester polyol was synthesized from oleochemical glycerol monostearate (GMS) and glutaric acid under a non-catalyzed and solvent-free polycondensation method. The chemical structure of GMS-derived polyester polyol (GPP) was elucidated by FTIR, ¹H and ¹³C NMR, and molecular weight of GPP was characterized by GPC. The synthesized GPP with acid value of 3.03 mg KOH/g sample, hydroxyl value of 115.72 mg KOH/g sample and M_n of 1345 g/mol was incorporated with polyethylene glycol (PEG) and polycaprolactone diol (PCL diol) to produce a water-blown porous polyurethane system via one-shot foaming method. The polyurethanes were optimized by evaluating glycerol as a crosslinker, silicone surfactant and water blowing agent on tensile properties of polyurethanes. All polyurethanes underwent structural change, and crystalline hard segments of polyurethanes were shifted to higher temperature suggested that hard segments undergone re-ordering process during enzymatic treatment. In terms of biocompatibility, polyurethane scaffold produced by reacting 100% w/w of GPP with isophorone diisocyanate and additives showed the highest cells viability of 3T3 mouse fibroblast (94%, day 1), and MG63 human osteosarcoma (107%, day 1) and better cell adhesion as compared to reference polyurethane produced by only PEG and PCL diol (3T3 cell viability: 8%; MG63 cell viability: 2%). The current work demonstrated GPP synthesized from renewable and environmental friendly resources produced polyurethanes that allows improvement in physico-chemical, mechanical and biocompatibility properties. By blending with increasing content of GPP, the water-blown porous polyurethane scaffold has shown great potential as biomaterial for soft and hard tissue engineering.     

Rate constants of dichloride radical anion reactions with molecules of environmental interest in aqueous solution: a review

Environmental Science and Pollution Research - Natural waters, water droplets in the air at coastal regions and wastewaters usually contain chloride ions (Cl-) in relatively high concentrations in...     

Monitoring of emissions from selected trades and industries in Hong Kong

A survey on the concentration of organic and inorganic compounds emitted from various trades and industries in Hong Kong was performed to indicate the level of pollutants occuring in the factories, in the stacks and their dispersion into the environment. The results indicate that none of the organic or inorganic compounds present in the workplace exceed the TLV value for the factories during the visit in the two years period of study. However, the concentration of the chemistry compounds in the stack are found to be very high, with NH₃ and HCl exceeding the emission limits. As the dispersion of pollutants in a highly populated place like Hong Kong is an important concern, the effect of prominent stationary sources on the nearby population were investigated qualitatively to establish their contribution to the pollution level at the receptor site in addition to the background pollutant level. Due to the lack of input meteorological data and the highly complex topology around most sites amongst high-rise buildings in Hong Kong, it is difficult to use advanced computer model dealing with complex terrain. Instead, a simple impaction formula was tested for its applicability in Hong Kong. The results indicate an over estimation of the experimental value. Nevertheless, it could be used to provide a rough estimate of the upper limit of the pollutant concentration at given receptor sites. The feasibility of assessing the contribution or different stationary sources to the particulate collected at given receptor sites was studied and work is in progress to obtain a more comprehensive pollutant data inventory for the above assessment.     

Denitrification with carbon addition--kinetic considerations

The Blue Plains Advanced Wastewater Treatment Plant (Washington, D.C.) uses methanol as an external carbon source in a postdenitrification process, to achieve low effluent total nitrogen concentrations. This becomes more difficult in winter, at lower mixed liquor temperatures and higher flows, as a consequence of the kinetic behavior of the methanol-utilizing heterotrophs. The paper reports on an experimental batch test study conducted on Blue Plains postdenitrification sludge to investigate (1) the maximum specific growth rate of methanol-utilizing heterotrophs (Mu(METH)); (2) the temperature dependency of the growth rate; and (3) the efficacy of alternate substrates (ethanol, acetate, and sugar). A limited number of tests were conducted on sludge from two other treatment plants with methanol addition.     

Elemental composition of Jamaican foods 1: A survey of five food crop categories

The concentrations of 27 elements in Jamaican food categories consisting of fruit, legumes, leafy and root vegetables and other root crops are reported. The main analytical techniques used were neutron activation analysis and flame and graphite furnace atomic absorption spectrophotometry. The results are compared, where possible, with values from Denmark, the United Kingdom, the United States and Nigeria, and with some regulatory limits. Over 75% of the results for antimony, arsenic, barium, cerium, thorium and uranium were below the respective sample detection limits but even among these, some of the maximum values observed indicate that further examination may be useful for those foods grown in the regions of highest uptake and consumed in large amounts. The other elements reported are bromine, cadmium, calcium, caesium, cerium, chromium, copper, europium, hafnium, iron, lanthanum, lead, magnesium, manganese, phosphorus, potassium, rubidium, scandium, samarium, sodium, strontium, thorium, uranium, and zinc. Many of these elements occur at concentration levels above those reported from the other countries but it seems unlikely that most of these will contribute significantly to public health risk. However, at this stage cadmium clearly appears to be the element of greatest concern in the Jamaican food chain. The observed range of cadmium concentrations suggests that factors such as land selection, coupled perhaps where necessary, with suitably modified agricultural practices, is a feasible way to reduce the cadmium content of certain local foods.