Relationships between analytical methods utilized as tools in the evaluation of landfill waste stability

In this study, the refuse from 12 landfills of various ages ranging from fresh refuse to material 11 years old was collected, and changes in the bio-stability parameters were determined. The parameters measured included cellulose, lignin, biochemical methane potential (BMP) and volatile solids, along with plastics. These parameters, along with the cellulose to lignin ratio were compared to determine which were most indicative of the bio-stability of the refuse. Lignin and volatile solids measurements were affected by plastics in refuse samples. Plastics increased both lignin and volatile solids measurements by approximately 10%. Cellulose and volatile solids measurements correlated well with age, each other, and with BMP measurements and were therefore considered the best parameters to determine stability. Data for the Riverbend landfill, a landfill with a moisture content of 48%, which is similar to that of bioreactor landfills, showed that degradation was nearly complete after 5 years as indicated by low values for cellulose and BMP.     

An evaluation of the interaction of morning residual layer and afternoon mixed layer ozone in Houston using ozonesonde data

The Tropospheric Ozone Pollution Project (TOPP) launched >220 ozonesondes in Houston (July 2004–June 2008) providing examples of pollution transported into, re-circulated within, and exported from the Houston area. Fifty-one launches occurred during the Texas Air Quality Study (TexAQS) II and the summer portion of IONS-06 (INTEX [Intercontinental Transport Experiment] Ozonesonde Network Study). On 11 days during TexAQS II and on 8 other occasions, ozonesondes were launched both at dawn and in the afternoon. Analysis of these “intensive” launch sequences shows that morning residual layer (RL) ozone concentrations ([O₃]) explained 60–70% of the variability found in the afternoon mixed layer (ML). Furthermore, maximum RL [O₃] is nearly identical to the mean ML [O₃] from the previous afternoon (morning minus afternoon = ?1.6 ± 8.4 ppbv). During TexAQS II, mean [O₃] below 1.3 km (the mean ML height from ozonesonde data) increased from 37 ± 22 ppbv in the morning to 74 ± 18 ppbv in the afternoon, suggesting an average net local daily O₃ production of ～500–900 tons over the metropolitan Houston area.     

Windsor, Ontario exposure assessment study: design and methods validation of personal, indoor, and outdoor air pollution monitoring

The Windsor, Ontario Exposure Assessment Study evaluated the contribution of ambient air pollutants to personal and indoor exposures of adults and asthmatic children living in Windsor, Ontario, Canada. In addition, the role of personal, indoor, and outdoor air pollution exposures upon asthmatic children's respiratory health was assessed. Several active and passive sampling methods were applied, or adapted, for personal, indoor, and outdoor residential monitoring of nitrogen dioxide, volatile organic compounds, particulate matter (PM; PM < or = 2.5 microm [PM2.5] and < or = 10 microm [PM10] in aerodynamic diameter), elemental carbon, ultrafine particles, ozone, air exchange rates, allergens in settled dust, and particulate-associated metals. Participants completed five consecutive days of monitoring during the winter and summer of 2005 and 2006. During 2006, in addition to undertaking the air pollution measurements, asthmatic children completed respiratory health measurements (including peak flow meter tests and exhaled breath condensate) and tracked respiratory symptoms in a diary. Extensive quality assurance and quality control steps were implemented, including the collocation of instruments at the National Air Pollution Surveillance site operated by Environment Canada and at the Michigan Department of Environmental Quality site in Allen Park, Detroit, MI. During field sampling, duplicate and blank samples were also completed and these data are reported. In total, 50 adults and 51 asthmatic children were recruited to participate, resulting in 922 participant days of data. When comparing the methods used in the study with standard reference methods, field blanks were low and bias was acceptable, with most methods being within 20% of reference methods. Duplicates were typically within less than 10% of each other, indicating that study results can be used with confidence. This paper covers study design, recruitment, methodology, time activity diary, surveys, and quality assurance and control results for the different methods used.     

Use of mixed technologies to remediate chlorinated DNAPL at a Brownfields site

A former chlorofluorocarbon manufacturing facility in northern New Jersey was purchased for redevelopment as a warehousing/distribution center as part of the New Jersey Department of Environmental Protection's Brownfields redevelopment initiative. Soil and groundwater at the site were impacted with dense nonaqueous‐phase liquids (chlorinated organic compounds) and light nonaqueous‐phase liquids (petroleum hydrocarbons). The initial remedial strategy (excavation and offsite disposal) developed by prior site owners would have been cost‐prohibitive to the new site owners and made redevelopment infeasible. Mixed remedial technologies were employed to reduce the cost of remediation while meeting regulatory contaminant levels that are protective of human health and the environment. The most heavily impacted soils (containing greater than 95 percent of the contaminant mass) were excavated and treated onsite by the addition of calcium oxide and lime kiln dust coupled with physical mixing. Treated soils were reused onsite as part of the redevelopment. Residual soil and groundwater contamination was treated via in situ injections of emulsified oil to enhance anaerobic biodegradation, and emulsified oil/zero‐valent iron to chemically reduce residual contaminants. Engineering (cap) and administrative (deed restriction) controls were used as part of the final remedy. The remedial strategy presented in this article resulted in a cost reduction of 50 percent of the initial remedial cost estimate. © 2008 Wiley Periodicals, Inc.     

Probabilistic assessment of the potential indoor air impacts of vent-free gas heating appliances in energy-efficient homes in the United States

Use of vent-free gas heating appliances for supplemental heating in U.S. homes is increasing. However, there is currently a lack of information on the potential impact of these appliances on indoor air quality for homes constructed according to energy-efficient and green building standards. A probabilistic analysis was conducted to estimate the impact of vent-free gas heating appliances on indoor air concentrations of carbon monoxide (CO), nitrogen dioxide (NO₂), carbon dioxide (CO₂), water vapor, and oxygen in “tight” energy-efficient homes in the United States. A total of 20,000 simulations were conducted for each Department of Energy (DOE) heating region to capture a wide range of home sizes, appliance features, and conditions, by varying a number of parameters, e.g., room volume, house volume, outdoor humidity, air exchange rates, appliance input rates (Btu/hr), and house heat loss factors. Predicted airborne levels of CO were below the U.S. Environmental Protection Agency (EPA) standard of 9 ppm for all modeled cases. The airborne concentrations of NO₂ were below the U.S. Consumer Product Safety Commission (CPSC) guideline of 0.3 ppm and the Health Canada benchmark of 0.25 ppm in all cases and were below the World Health Organization (WHO) standard of 0.11 ppm in 99–100% of all cases. Predicted levels of CO₂ were below the Health Canada standard of 3500 ppm for all simulated cases. Oxygen levels in the room of vent-free heating appliance use were not significantly reduced. The great majority of cases in all DOE regions were associated with relative humidity (RH) levels from all indoor water vapor sources that were less than the EPA-recommended 70% RH maximum to avoid active mold and mildew growth. The conclusion of this investigation is that when installed in accordance with the manufacturer’s instructions, vent-free gas heating appliances maintain acceptable indoor air quality in tight energy-efficient homes, as defined by the standards referenced in this report.

Implications: Probabilistic modeling of indoor air concentrations of carbon monoxide (CO), nitrogen dioxide (NO₂), carbon dioxide (CO₂), water vapor, and oxygen associated with use of vent-free gas heating appliances provides new data indicating that uses of these devices are consistent with acceptable indoor air quality in “tight” energy-efficient homes in the United States. This study will provide authoritative bodies such as the International Code Council with definitive information that will assist in the development of future versions of national building codes, and will provide evaluation of the performance of unvented gas heating products in energy conservation homes.     

Recycling Irrigation Reservoir Stratification and Implications for Crop Health and Production

Recycling irrigation reservoirs (RIRs) are an emerging aquatic ecosystem and water resource of global significance. This study investigated the vertical distribution of water temperature, dissolved oxygen (DO), and pH in eight RIRs at two nurseries each in Virginia and Maryland from 2011 to 2014. Monomictic thermal stratification was observed from April to October in all RIRs, despite their shallow depths (0.75‐3.89 m). The strongest stratification had a top‐bottom temperature difference of 21.53°C. The top‐bottom temperature difference was positively correlated with water column depth, air temperature, and daily light integral (p < 0.05). Wind speed did not impact the thermal stratification, likely due to their relatively small surface areas. Thermal stratification affected the vertical distribution of DO and pH. The top‐bottom differences in DO and pH were greater during stratification periods than nonstratification periods. Water pH in all RIRs was higher at the top than at the bottom with the greatest difference of 4.16 units. Discovery and characterization of thermal stratification in RIRs helps understand water quality dynamics in this novel ecosystem and promote safe and productive water reuse for irrigation. Specifically, water withdrawal depths should be adjusted according to variations in temperature, DO, and pH during the stratification and nonstratification periods to mitigate pathogen risk and improve water treatment efficacy and crop production.     

Building community resilience: can everyone enjoy a good life?

Initiatives to reduce community carbon emissions and foster sustainable lifestyles have had varying degrees of success. There is now a need for a re-energised, concerted and joined-up approach that places environmental issues in a wider context – one that improves quality of life while building community resilience. This involves enhancing the capacity of neighbourhoods to recover, respond and adapt to environmental and socio-economic changes. This paper examines the experience gained in a participatory action research (PAR) study to build community resilience, where facilitators supported residents to take ownership of their own agendas. The New Earswick Good Life Initiative (GLI) was an 18-month project undertaken in a low-income suburb of York (UK). A range of approaches were used to identify activities which had the most potential to nurture resilience and foster a shift towards greater environmental sustainability. The GLI highlighted how the introduction of new ideas not only need to be locally relevant but also requires care and time in order for them to embed within community. Altering the way a community manages its environment involves transforming social relationships, strengthening institutions and influencing local power balances. Furthermore, it is necessary to build social capital, knowledge, leadership skills and support social networks to allow communities to effectively engage with relevant local and national policies. Only by providing opportunities to develop these resilient attributes can increased local responsibility be successful. The paper concludes by providing guidance on strengthening community resilience and delivering pro-environmental behaviour change.     

Integrative research on environmental and landscape change: PhD students' motivations and challenges

The growing demand for integrative (interdisciplinary or transdisciplinary) approaches in the field of environmental and landscape change has increased the number of PhD students working in this area. Yet, the motivations to join integrative projects and the challenges for PhD students have so far not been investigated. The aims of this paper were to identify the understanding of PhD students with regard to integrative research, their motivations to join integrative projects, their expectations in terms of integration and results, and to reveal the challenges they face in integrative projects. We collected data by a questionnaire survey of 104 PhD students attending five PhD Master Classes held from 2003 to 2006. We used manual content analysis to analyse the free-text answers. The results revealed that students lack a differentiated understanding of integrative approaches. The main motivations to join integrative projects were the dissertation subject, the practical relevance of the project, the intellectual stimulation of working with different disciplines, and the belief that integrative research is more innovative. Expectations in terms of integration were high. Core challenges for integration included intellectual and external challenges such as lack of knowledge of other disciplines, knowledge transfer, reaching depth, supervision, lack of exchange with other students and time demands. To improve the situation for PhD students, we suggest improving knowledge on integrative approaches, balancing practical applicability with theoretical advancement, providing formal introductions to other fields of research, and enhancing institutional support for integrative PhD projects.     

Removal of toxic ions (chromate, arsenate, and perchlorate) using reverse osmosis, nanofiltration, and ultrafiltration membranes

Rejection characteristics of chromate, arsenate, and perchlorate were examined for one reverse osmosis (RO, LFC-1), two nanofiltration (NF, ESNA, and MX07), and one ultrafiltration (UF and GM) membranes that are commercially available. A bench-scale cross-flow flat-sheet filtration system was employed to determine the toxic ion rejection and the membrane flux. Both model and natural waters were used to prepare chromate, arsenate, and perchlorate solutions (approximately 100 μg L⁻¹ for each anion) in mixtures in the presence of other salts (KCl, K₂SO₄, and CaCl₂); and at varying pH conditions (4, 6, 8, and 10) and solution conductivities (30, 60, and 115 mS m⁻¹). The rejection of target ions by the membranes increases with increasing solution pH due to the increasingly negative membrane charge with synthetic model waters. Cr(VI), As(V), and rejection follows the order LFC-1 (>90%) > MX07 (25–95%)  ESNA (30–90%) > GM (3–47%) at all pH conditions. In contrast, the rejection of target ions by the membranes decreases with increasing solution conductivity due to the decreasingly negative membrane charge. Cr(VI), As(V), and rejection follows the order CaCl₂ < KCl  K₂SO₄ at constant pH and conductivity conditions for the NF and UF membranes tested. For natural waters the LFC-1 RO membrane with a small pore size (0.34 nm) had a significantly greater rejection for those target anions (>90%) excluding (71–74%) than the ESNA NF membrane (11–56%) with a relatively large pore size (0.44 nm), indicating that size exclusion is at least partially responsible for the rejection. The ratio of solute radius (r_i,s) to effective membrane pore radius (r_p) was employed to compare ion rejection. For all of the ions, the rejection is higher than 70% when the r_i,s/r_p ratio is greater than 0.4 for the LFC-1 membrane, while for di-valent ions (, , and ) the rejection (38–56%) is fairly proportional to the r_i,s/r_p ratio (0.32–0.62) for the ESNA membrane.     

Individual particle characteristics of North African dust under different long-range transport scenarios

After urban sources, mineral dust in Madrid is the second biggest contributor to PM₁₀, making up 40% on average, of total emissions. Approximately, 50% of the days on which the daily limit of 50 μg m^?3 marked by the European Directive, are ascribable to Saharan outbreaks. The present study has focused on individual particle characterization of North African dust over Madrid by SEM/EDX, since no previous works on this type of characterization have been found in the region. More than 30,000 particles from 6 different samples have been measured to characterize 4 African episodes with very different meteorological scenarios, transport processes and source origins. Different samples from the same episode have also been characterized to evaluate homogeneity of dust characteristics over time. Silicates, mainly composed of clay minerals, are the main component, with abundances ranging from 65 to 85% by particle volume. Chemical cluster distribution of silicates has been linked to the major topsoil mineralogical composition in the origin of the episodes. Aspect Ratio (AR) has been used to compare particle morphology between episodes. AR values from samples taken under the same scenarios are statistically equal. For all the samples and size ranges AR values are found to be in the same order: AR_sulphates > AR_silicates > AR_carbonates. Particles not only maintained morphology during the episode, but also chemical composition, since clusters turned out to be very similar in samples taken on the same day and different days. Similarities and differences in particle chemical composition and morphology between the different transport patterns are discussed in detail throughout the paper.