Remediation of MTBE from drinking water: air stripping followed by off-gas adsorption

The widespread use of methyl tertiary butyl ether (MTBE) as an oxygenate in gasoline has resulted in the contamination of a large number of ground and surface water sources. Even though air stripping has been proven to be an effective treatment technology for MTBE removal, off-gas treatment often is required in conjunction with it. This study evaluated the combined treatment technologies of air stripping followed by off-gas adsorption on a pilot scale for the treatment of MTBE-contaminated water. The effect of air/water ratios on the treatment efficiency was studied, and the mass transfer coefficient was determined. Air/water ratios of 105:1, 151:1, 177:1, 190:1, 202:1, and 206:1 were used, and a treatment efficiency of >99% was achieved for all the runs conducted. The depth of packing required to achieve maximum treatment efficiency decreased with increasing air/water ratio. Relative humidity (RH) impacts on the MTBE adsorption capacity of a granular activated carbon (GAC) and carbonaceous resin were determined from pilot plant studies. Breakthrough profiles obtained from the pilot plant studies conducted at 20, 30, and 50% RH indicated that GAC has a higher adsorptive capacity than resin. The adsorptive capacity of GAC decreased with increasing RH, whereas RH did not impact the resin adsorptive capacity.     

Development of emission factors for polycarbonate processing

Emission factors for selected volatile organic compounds (VOCs) and particulate emissions were developed while processing eight commercial grades of polycarbonate (PC) and one grade of a PC/acrylonitrile-butadiene-styrene (ABS) blend. A small commercial-type extruder was used, and the extrusion temperature was held constant at 304 degrees C. An emission factor was calculated for each substance measured and is reported as pounds released to the atmosphere/million pounds of polymer resin processed [ppm (wt/wt)]. Scaled to production volumes, these emission factors can be used by processors to estimate emission quantities from similar PC processing operations.     

Napropamide residues in runoff and infiltration water from pepper production

A field study was conducted on a Lowell silty loam soil of 2.7% organic matter at the Kentucky State University Research Farm, Franklin County, Kentucky. Eighteen universal soil loss equation (USLE) standard plots (22 x 3.7 m each) were established on a 10% slope. Three soil management practices were used: (i) class-A biosolids (sewage sludge), (ii) yard waste compost, each mixed with native soil at a rate of 50 ton acre(-1) on a dry-weight basis, and (iii) a no-mulch (NM) treatment (rototilled bare soil), used for comparison purposes. Devrinol 50-DF "napropamide" [N,N-diethyl-2-(1-naphthyloxy) propionamide] was applied as a preemergent herbicide, incorporated into the soil surface, and the plots were planted with 60-day-old sweet bell pepper seedlings. Napropamide residues one hour following spraying averaged 0.8, 0.4, and 0.3 microg g(-1) dry soil in sewage sludge, yard waste compost, and no-mulch treatments, respectively. Surface runoff water, runoff sediment, and napropamide residues in runoff were significantly reduced by the compost and biosolid treatments. Yard waste compost treatments increased water infiltration and napropamide residues in the vadose zone compared to sewage sludge and NM treatments. Total pepper yields from yard waste compost amended soils (9187 lbs acre(-1)) was significantly higher (P < 0.05) than yield from either the soil amended with class-A biosolids (6984 lbs acre(-1)) or the no-mulch soil (7162 lbs acre(-1)).     

Kinship and food availability influence cannibalism tendency in early-instar wolf spiders (Araneae: Lycosidae)

For potentially cannibalistic animals such as spiders, the ability to recognize and avoid kin and/or preferentially cannibalize non-relatives would permit exploiting conspecifics as prey while minimizing loss of inclusive fitness. We investigated the effects of relatedness and availability of alternative food on cannibalism tendency in pairs of juvenile Hogna helluo (Walckenaer), a North American wolf spider (Araneae: Lycosidae). For second-instar spiderlings (dispersing stage), cannibalism was more likely among pairs of non-sibs than pairs of sibs and, interestingly, was also more likely when other prey were available. We found no evidence of increased cannibalism in pairings involving broods of greatest average size disparity, indicating that size differences are unlikely to explain differences in cannibalism tendency. Additionally, the relative number of deaths from cannibalism or other causes did not increase with increasing risk of starvation. For third-instar spiderlings, which had lived independently of their mother and sibs following dispersal, cannibalism rates were very high in all treatments and there were no significant effects of relatedness or food availability. Our results suggest that spiders with predominantly solitary lifestyles may bias cannibalism toward non-kin during the juvenile associative period, and that this effect is lost in the subsequent instar. Results are discussed in the context of several potential mechanisms that might result in differential cannibalism.Communicated by M. Elgar     

A national critical loads framework for atmospheric deposition effects assessment: III. Deposition characterization

Methods are discussed for describing patterns of current wet and dry deposition under various scenarios. It is proposed that total deposition data across an area of interest are the most relevant in the context of critical loads of acidic deposition, and that the total (i.e., wet plus dry) deposition will vary greatly with the location, the season, and the characteristics of individual subregions. Wet and dry deposition are proposed to differ in such fundamental ways that they must be considered separately. Both wet and dry deposition rates are controlled by the presence of the chemical species in question in the air (at altitudes of typically several kilometers in the case of wet deposition, and in air near the surface for dry). The great differences in the processes involved lead to the conclusion that it is better to measure wet and dry deposition separately and combine these quantifications to produce “total deposition” estimates than to attempt to derive total deposition directly. A number of options for making estimates of total deposition to be used in critical loads assessment scenarios are discussed for wet deposition (buckets and source receptor models) and for dry deposition (throughfall, micrometeorology, surrogate surfaces and collection vessels, inference from concentrations, dry-wet ratios, and source-receptor models). The research described in this article has been funded by the US Environmental Protection Agency. This document has been prepared at the EPA Environmental Research Laboratory in Corvallis, Oregon, through contract #68-C8-0006 with ManTech Environmental Technology, Inc., and Interagency Agreement #1824-B014-A7 with the U.S. Department of Energy and at Oak Ridge National Laboratory managed by Martin Marietta Energy Systems, Inc., under Contract DE-AC05-84OR21400 with the US Department of Energy. Environmental Sciences Division Publication No. 3905. It has been subjected to the Agency’s peer and administrative review and approved for publication. Mention of trade names or commercial products does not constitute endorsement or recommendation for use.     

A national critical loads framework for atmospheric deposition effects assessment: I. Method summary

The United States Environmental Protection Agency (EPA), with the assistance of the US Department of Energy (DOE) and the National Oceanographic and Atmospheric Administration (NOAA) is examining the utility of a critical loads approach for evaluating atmospheric pollutant effects on sensitive ecosystems. A critical load has been defined as, “a quantitative estimate of an exposure to one or more pollutants below which significant harmful effects on specified sensitive elements of the environment do not occur according to present knowledge.” Working in cooperation with the United Nations Economic Community for Europe’s (UN-ECE) Long Range Transboundary Air Pollution (LRTAP) Convention, the EPA has developed a flexible, six-step approach for setting critical loads for a range of ecosystem types. The framework is based on regional population characteristics of the ecosystem(s) of concern. The six steps of the approach are: (1) selection of ecosystem components, indicators, and characterization of the resource; (2) definition of functional subregions; (3) characterization of deposition within each of the subregions; (4) definition of an assessment end point; (5) selection and application of models; and (6) mapping projected ecosystem responses. The approach allows for variable ecosystem characteristics and data availability. Specific recognition of data and model uncertainties is an integral part of the process, and the use of multiple models to obtain ranges of critical loads estimates for each ecosystem component in a region is encouraged. Through this intercomparison process uncertainties in critical loads projections can be estimated. The research described in this article has been funded by the US Environmental Protection Agency. This document has been prepared at the EPA Environmental Research Laboratory in Corvallis, Oregon, through contract #68-C8-0006 with Man Tech Environmental Technology, Inc. It has been subjected to the agency’s peer and administrative review and approved for publication. Mention of trade names or commercial products does not constitute endorse ment or recommendation for use.