Removal of arsenic(III,V) by a granular Mn-oxide-doped Al oxide adsorbent: surface characterization and performance

In order to remove arsenic (As) from contaminated water, granular Mn-oxide-doped Al oxide (GMAO) was fabricated using the compression method with the addition of organic binder. The analysis results of XRD, SEM, and BET indicated that GMAO was microporous with a large specific surface area of 54.26 m^2/g, and it was formed through the aggregation of massive Al/Mn oxide nanoparticles with an amorphous pattern. EDX, mapping, FTIR, and XPS results showed the uniform distribution of Al/Mn elements and numerous hydroxyl groups on the adsorbent surface. Compression tests indicated a satisfactory mechanical strength of GMAO. Batch adsorption results showed that As(V) adsorption achieved equilibrium faster than As(III), whereas the maximum adsorption capacity of As(III) estimated from the Langmuir isotherm at 25 °C (48.52 mg/g) was greater than that of As(V) (37.94 mg/g). The As removal efficiency could be maintained in a wide pH range of 3~8. The presence of phosphate posed a significant adverse effect on As adsorption due to the competition mechanisms. In contrast, Ca²⁺ and Mg²⁺ could favor As adsorption via cation-bridge involvement. A regeneration method was developed by using sodium hydroxide solution for As elution from saturated adsorbents, which permitted GMAO to keep over 75% of its As adsorption capacity even after five adsorption–regeneration cycles. Column experiments showed that the breakthrough volumes for the treatment of As(III)-spiked and As(V)-spiked water (As concentration = 100 μg/L) were 2224 and 1952, respectively. Overall, GMAO is a potential adsorbent for effectively removing As from As-contaminated groundwater in filter application.

     

The implementation of a measurement system for brushless DC motor parameters

Most of the energy conversion in industrial devices and equipment is completed by the motor. The acquirement of motor parameters becomes very important for designing the motor drives. The aim of this paper is to design and implement a motor measurement system. Through the processing of an Advanced RISC Machines (ARM) microcontroller, the various parameters of motors such as input voltage, input current, input power, motor speed, and motor torque can be obtained. Consequently, the torque constant, load torque, viscous friction, and the inertia of the motor are calculated and achieved. The motor parameters can be commanded and displayed in the designed human interface of a PC via USB communication. The hardware system designed in this system includes an ARM microcontroller, an inverter, a voltage sensor, a current sensor, a torque sensor, and power supply. The software programming is developed under the Visual Studio 2012 environment development platform using the C language. Finally, the prototype of the motor measurement system is completed and verified. The experimental results for the motor parameters and torque/speed characteristic are demonstrated and show the feasibility of the complete designed system.     

水泥窑共处置废物过程中重金属的流向分布

为了探索水泥窑共处置危险废物过程中重金属流向分布规律,研究了不同温度条件下Cr、As、Pb在煅烧熟料、颗粒物和尾气中的残留率。在900、1 000、1 100、1 200、1 300和1 450℃温度条件下,将添加Cr、As和Pb化学试剂的生料分别进行煅烧,模拟重金属在水泥窑内不同温度带的煅烧过程。结果表明,6个温度条件下,Cr主要分布在熟料中并且呈现不规则变化;颗粒物中的Cr在1 200℃条件下分布量最大,所占比例为32.79%(w);在900℃和1450℃条件下,烟气中的Cr分布量最大,所占比例为0.24%(w)。6个温度条件下As主要分布在熟料中并且1 000~1 450℃条件下稳定在81%~83%之间;在900℃条件下,As在熟料中的残留率最大,所占比例为97%(w);在1450℃条件下,As在尾气中的分布达到最大值,所占比例为0.0023%(w)。6个温度条件下,Pb在熟料中的残留率随着温度升高而逐渐减少,挥发颗粒物中的含量呈现相反的趋势;尾气中Pb的含量随着温度的升高逐渐增加。     

PCBs污染土壤的CaO诱导低温热处理脱氯研究

研究了低温热处理脱氯技术对废弃电容器封存点附近污染土壤中多氯联苯脱氯的效果,考察反应温度、反应时间及CaO添加比例对PCBs去除率、脱氯率的影响以及反应前后土壤中污染物的组分变化。实验土样中PCBs浓度为107.7 mg/g,属于罕见高浓度PCBs污染土壤。当反应温度为400℃、停留时间4h、CaO添加比例为10%,PCBs的去除率为87.7%,脱氯率为85.3%。土壤样品中五氯联苯和四氯联苯反应后含量降低或未检出,部分反应后样品检出一氯联苯和联苯,说明在CaO诱导PCBs低温热处理脱氯反应中存在逐步脱氯/加氢反应途径。     

絮团粘性分维数的概念及其分析模型

水处理中的絮团具有复杂的形态结构,分维数是描述这种结构的有力工具。通过分析固液体系的粘度与絮团分维数之间的关系,提出了絮团粘性分维数的新概念及粘性分维数测定的数学物理模型,并进行了实验验证。与常用的质量分维数、边界分维数、面积分维数、体积分维数、表面积分维数等相比,絮团的粘性分维数及其测定模型具有易于测量、可同时表征不同类型絮团、可定量分析絮凝产品组成等特点,从而为絮团形态结构的定性及定量研究开辟了新的途径。     

气浮技术在膜生物反应器剩余污泥浓缩过程中的应用

污泥浓缩作为污泥处理的关键环节之一,开发高效的污泥浓缩工艺对于降低污泥含水率、提高脱水设备的运行效率、降低脱水能耗具有十分重要的意义。针对MBR污泥浓度高、污泥粒径小、污泥沉降性能较差等特点,故采用传统的重力浓缩和机械浓缩技术很难有效实现污泥浓缩。因此,尝试采用气浮浓缩技术降低污泥含水率的可行性。从气浮浓缩的中试结果来看,较适宜运行参数为:固体负荷为15 kg/(m2·h),水力负荷为1.5 m3/(m2·h),回流比为1,PAM投配率2‰(w/w干固体),溶气压力为0.4 MPa,气固比为0.03。经过中试设备进行气浮浓缩后,污泥含水率降低至96%左右。此外,还研究了采用气液多相泵系统对剩余污泥的浓缩效率,结果显示,该设备的使用相对于传统溶气气浮工艺,其优点表现在占地小、工程造价低以及运行成本低等方面。     

KOH活化花生壳生物质炭对亚甲基蓝吸附性能研究

以花生壳生物质炭(P-BC)为原料,KOH为活化剂,采用化学活化法制得活化生物质炭(K-BC),通过考察对亚甲基蓝的吸附性能,研究了花生壳生物质炭的最佳活化条件,并利用N2吸附-脱附实验、SEM等对最佳活化条件下的生物质炭进行表征。结果表明,K-BC活化的最佳条件为碱炭比为1.5∶1,活化温度为800℃,活化时间为90 min,此时K-BC的比表面积达到597.93 m2/g,总孔容达到0.76 cm3/g。并考察了亚甲基蓝初始浓度、pH等对K-BC吸附亚甲基蓝的影响,随着初始浓度的增加,吸附平衡时间显著延长,亚甲基蓝去除率显著降低;当pH=6时,K-BC对亚甲基蓝的吸附量最大;K-BC对亚甲基蓝的吸附动力学曲线符合伪二阶动力学模型,吸附平衡时K-BC对亚甲基蓝的吸附能力为80~149.95 mg/g。     

原铝生产流程温室气体排放主要影响因素的关联度分析

铝是国民经济建设和发展的关键基础材料,然而由其生产过程所产生的大量温室气体排放也逐渐成为政府关注的焦点。本研究计算了我国原铝生产不同年度的生命周期能耗和温室气体排放量,并分析了资源消耗和生产工序能耗等影响因素与温室气体排放的关联性。结果表明,在各年原铝生产的温室气体排放总量中,电力和阳极效应导致的排放所占比重分别为68.5%和7.9%,其他影响因素所占比重均低于6%;与温室气体排放关联度最高的3个影响因素依次是电耗、煤气燃烧和石灰石煅烧,其值分别为0.937、0.899和0.893;在目前铝电耗和阳极效应控制水平提升空间有限的情况下,降低煤气的消耗,提高石灰石的使用效率,是实现原铝生产温室气体减排的有效途径。     

CdIn2S4/复合材料的制备及光降解罗丹明B

利用高压静电纺丝技术,制得含有羧基的导电聚合物纤维(聚偏氟乙烯/苯乙烯-马来酸酐共聚物/纳米石墨),高温水热条件下在纤维表面制备CdIn2S4颗粒,得到CdIn2S4/导电聚合物纤维复合材料。运用扫描电子显微镜(SEM)、X射线衍射仪(XRD)、紫外-可见吸收光谱仪(UV-Vis)和热失重分析仪(TGA)对复合材料的结构进行表征。并利用350 W氙灯模拟太阳光进行光催化降解罗丹明B。结果发现,CdIn2S4/导电聚合物纤维复合材料的降解效率高于CdIn2S4粉体和Degussa P25 TiO2粉体,光催化降解3 h,罗丹明B的降解率为96.2%。