负载稀土元素活性碳纤维在微型反应器中净化NO废气

以NH3为还原剂,以活性碳纤维（ACF）、HNO,浸渍的ACF、负载CuO的ACF和负载La2O3的ACF为催化剂,在微型反应器中考察各种催化剂对NO催化还原的活性,并进行了差热-热重、扫描电镜分析。实验结果表明,ACF负载La能有效地改善催化剂的活性,且催化活性中心为非晶态的氧化物;当ACF负载20％的La2O3时具有最好的低温活性,NO的去除率最高可达92％以上。     

生物表面活性剂产生菌犁头霉菌(Absidia orchidis)的筛选及发酵条件优化

采用植物油为唯一碳源,设计选择培养基,从饭店下水道污泥中筛选出生物表面活性剂产生菌.结果分离到12株菌,其中一株能使发酵液的表面张力值从68 mN·m-1降低到34.5 mN·m-1,具有开发潜力,被选出作进一步的研究.该菌株经鉴定为犁头霉菌(Absidia orchidis).通过正交试验对犁头霉菌的培养条件进行优化,其优化培养条件为:植物油3.6 g·L-1,KH2PO412.1 g·L-1,Na2HPO45 g·L-1,(NH4)2SO4 1 g·L-1,NaNO32 g·L-1,酵母浸膏0.1 g·L-1,MgSO4·7H2O 0.15 g·L-1,NaCl 5 g·L-1,CaCl2 0.1 g·L-1,EDTA 1 g·L-1,KI 0.83μg·L-1,H3PO4 0.01μg·L-1,CoCl2·6H2O 0.048μg·L-1,MnSO4·H2O 0.312μg·L-1,Na2 MoO4·2H2O 0.048μg·L-1,ZnCl2 0.287μg·L-1,CuSO4·5H2O 0.125μg·L-1,初始pH值8,接种量6%.发酵70h时可获得生物表面活性剂的最大收获量,此时发酵液中生物表面活性剂的相对浓度达402倍.     

UASB法处理城市生活垃圾焚烧场渗滤液

垃圾焚烧场的渗滤液具有pH低、污染成分复杂、COD_(Cr)浓度高、可生化性好等特点。本研究探索了UASB法处理焚烧场渗滤液时的快速启动方法,考察了水力停留时间、容积负荷对COD_(Cr)去除率的影响及产气量与COD_(Cr)去除率的关系,结果表明,在水力停留时间6d、容积负荷5kg/(m3.d)的情况下,COD_(Cr)去除率可达到93%,每升原水产气量可达22.5L,折合热值492.7kJ。     

伞罩型湿式脱硫除尘塔入口结构优化模拟

利用商用CFD软件Fluent,采用k-ε湍流模型和SIMPLE算法,对新型伞罩型湿式脱硫除尘塔内的三维两相流场进行数值模拟,发现了塔内烟气入口处流场所存在的不均匀性。为将其流场调节均匀从而提高脱硫除尘效率,在数值模拟的基础上提出在入口处加装直导流板、阶梯导流板和弯曲导流板,并分析塔内y=0截面速度的分布,以及z＝0.21 m截面上的颗粒浓度、速度和压力等参数的分布。结果表明：通过加装阶梯导流板和弯曲导流板均可以将流场调节均匀,达到较理想状态,从而实现高效净化气体的目的。模拟结果对设备的优化设计和实际运行有一定的指导作用。     

表面活性剂加强动电技术去除污泥中铜和镉

以实际城市污泥为研究对象,通过采用表面活性剂作为阴极液,并考虑阴极液pH值、表面活性剂类型和电压3种因素对动电技术去除污泥中重金属(铜和镉)的影响,选用正交试验确定最佳试验条件.结果表明,采用表明活性剂作为阴极液加强动电技术去除污泥中重金属足可行的,铜和镉的去除率分别达到11.1%～52.6%和9.1%～46.7%.通过对正交试验结果进行极差和方差分析,试验的最佳条件为:电压为20 V,阴极液加入十六烷基三甲基氯化铵并控制pH值为4～6.表面活性剂的类型对动电技术去除镉具有显著影响.其中,表面活性剂类型对动电过程的影响最大,阴极液pH值次之,电压影响最小.     

Aerobic degradation of bisphenol A by Achromobacter xylosoxidans strain B-16 isolated from compost leachate of municipal solid waste

A novel bacterium designated strain B-16 was isolated from the compost leachate of the municipal solid waste (MSW) in a laboratory reactor. This strain was identified as a gram-negative bacterium, Achromobacter xylosoxidans that could grow on bisphenol A (BPA, a representative endocrine disruptor) as a sole carbon source under aerobic condition. BPA-degrading characteristics of strain B-16 were investigated in liquid cultures. The results show that BPA degradation was influenced by several factors (e.g. inoculum size, substrate concentration, temperature and pH, etc). The half-lives, optimum temperature and pH were found to be 0.58-3.1d, 35 degrees C and 7.0, respectively. BPA-degrading activity and cell growth were inhibited at high substrate concentration. Metabolic intermediates detected during the degradation process were identified as p-hydroxybenzaldehyde, p-hydroxybenzoic acid and p-hydroquinone, respectively. Metabolic pathway of BPA degradation was proposed in this study.     

Characteristic, composition, and sources of TSP investigated by HRTEM/EDS and ESEM/EDS

Total suspended particle (TSP) collected at the fifth floor of House Dust in Hunan University, China, was analyzed in terms of microscopic morphology and chemical composition. The fine particles (50?nm-2?μm) in the TSP were analyzed by a high-resolution transmission electron microscope equipped with an energy-dispersive X-ray analyzer (HRTEM/EDS). Results showed that the particles were in shapes of plate, irregular and agglomerate. Based on EDS results, these fine particulate matter was primarily composed of Fe-rich (35.82-61.29%), Ca-rich (30.18-36.77%) and Si-rich (18.95-32.28%) particles. Other elements mainly including Mg (0.47-4.97%), Al (0.45-14.57%), S (0.45-4.73%), K (1.13-2.13%) and Zn (0.67-3.85%) were also observed. The sources analysis indicated that the HRTEM particles mainly originated from coal combustion, traffic emission, vehicles exhaust emission and fugitive soil or cement particulate matter. The coarse particles (4-50?μm) were detected by environmental scanning electron microscopy coupled with energy-dispersive X-ray detector (ESEM/EDS). Based on a simple algorithm, ESEM particles were categorized into five groups: C-bearing (46.15%, 67% and 86.98%), Si + Ca-bearing (21.48?+?11.80%, 16.51?+?10.81% and 16.32?+?10.62%), Si + Al-bearing (20.06?+?12.40%, 20.16?+?11.22% and 15.31?+?11.25%), Si-bearing (34.40%, 26.92% and 27.15%) particles and aggregates, most of which exhibit obvious crystalline structure, and these ESEM particles mainly derived from vehicles exhaust emission, coal combustion, soil, and biomass burning, while the aggregates are indicative of atmospheric reaction progress. HRTEM/EDS and ESEM/EDS are mutual complementary in analyzing the characteristic and determining the sources of TSP.     

珠江三角洲4种淡水养殖鱼类重金属的残留及食用风险评价

为全面了解珠江三角洲淡水水产品中重金属污染现状,评估其生态风险与食用安全,于2014年8月至2015年8月采集罗非鱼、草鱼、乌鳢及鳜鱼主要养殖鱼类样品共计57份,采用原子荧光光谱仪(AFS),电感耦合等离子体质谱(ICP-MS)仪进行分析测定,并采用单因子污染指数(Pi)、重金属污染指数(MPI)、每周可耐受摄入量(PTWI)以及食入健康风险指标(Ri总)分别评估其污染程度、食用安全性与健康风险。结果表明,样品中Cr、Ni、Cu、Zn、As、Cd、Hg、Pb的含量范围分别为0.020~3.240,0.020~0.800,0.110~1.100,0.190~19.970,0.030~1.480,nd~0.606,0.003~0.118,0.040~0.803 mg·kg-1(湿重),Cr、As、Cd、Pb在水产品中超标率大小依次为As(7.0%),Pb(7.0%),Cd(5.3%),Cr(1.8%)。Pi结果表明,目前珠江三角洲养殖水域水产品中Cu与Zn残留处于正常范围内,Cr和Hg有少量样品为轻度污染,Pb、Cd与As存在重度污染样品,所占比例为2.86%、6.02%和5.74%。MPI结果显示不同水产品污染程度为乌鳢>鳜鱼>罗非鱼>草鱼,总体上各种水产品MPI依然处于较低的水平;食用安全性结果显示,目前成人每周摄入水产品是安全的,但乌鳢Cr,罗非鱼As含量较高分别达到PTWI的37.76%和19.51%,表明水产品中Cr、As残留可能存在一定的食用安全隐患。健康风险模型结果显示,所有样品均未超过国际辐射防护委员会(ICRP)的推荐的最大可接受水平(5×10-6a-1)。综合分析珠江三角洲淡水养殖主要水产品可知,其尚未出现明显的污染安全问题,但As与Cr等元素的潜在风险值得进一步关注。