Hazard property classification of waste according to the recent propositions of the EC using different methods

Hazard classification of waste is a necessity, but the hazard properties (named “H” and soon “HP”) are still not all defined in a practical and operational manner at EU level. Following discussion of subsequent draft proposals from the Commission there is still no final decision. Methods to implement the proposals have recently been proposed: tests methods for physical risks, test batteries for aquatic and terrestrial ecotoxicity, an analytical package for exhaustive determination of organic substances and mineral elements, surrogate methods for the speciation of mineral elements in mineral substances in waste, and calculation methods for human toxicity and ecotoxicity with M factors.In this paper the different proposed methods have been applied to a large assortment of solid and liquid wastes (>1 0 0).Data for 45 wastes – documented with extensive chemical analysis and flammability test – were assessed in terms of the different HP criteria and results were compared to LoW for lack of an independent classification. For most waste streams the classification matches with the designation provided in the LoW. This indicates that the criteria used by LoW are similar to the HP limit values.This data set showed HP 14 ‘Ecotoxic chronic’ is the most discriminating HP. All wastes classified as acute ecotoxic are also chronic ecotoxic and the assessment of acute ecotoxicity separately is therefore not needed. The high number of HP 14 classified wastes is due to the very low limit values when stringent M factors are applied to total concentrations (worst case method). With M factor set to 1 the classification method is not sufficiently discriminating between hazardous and non-hazardous materials. The second most frequent hazard is HP 7 ‘Carcinogenic’. The third most frequent hazard is HP 10 ‘Toxic for reproduction’ and the fourth most frequent hazard is HP 4 “Irritant – skin irritation and eye damage”. In a stepwise approach, it seems relevant to assess HP 14 first, then, if the waste is not classified as hazardous, to assess subsequently HP 7, HP 10 and HP 4, and then if still not classified as hazardous, to assess the remaining properties.The elements triggering the HP 14 classification in order of importance are Zn, Cu, Pb, Cr, Cd and Hg. Progress in the speciation of Zn and Cu is essential for HP 14. Organics were quantified by the proposed method (AFNOR XP X30-489) and need no speciation. Organics can contribute significantly to intrinsic toxicity in many waste materials, but they are only of minor importance for the assessment of HP 14 as the metal concentrations are the main HP 14 classifiers. Organic compounds are however responsible for other toxicological characteristics (hormone disturbance, genotoxicity, reprotoxicity…) and shall be taken into account when the waste is not HP 14 classified.     

Extending the environmental risk assessment for oseltamivir (Tamiflu®) under pandemic use conditions to the coastal marine compartment

In case of an avian-influenza-derived human flu pandemic, an inordinately high use of medicines over several weeks is predicted, in particular for the recommended influenza antiviral oseltamivir (Tamiflu). While the risk of oseltamivir to sewage works and freshwater bodies has already been assessed, the fact that a large percentage of the human population worldwide lives relatively close to the sea raises concern for its environmental compatibility in coastal marine waters. The potential risk of high oseltamivir use to the marine compartment is assessed in this publication, based on the 2003 European Community Technical Guidance Document (TGD) for risk assessment. Subchronic embryo–larval ecotoxicity tests with three marine invertebrates (Pomatoceros triqueter, Annelida; Mytilus edulis, Mollusca; Paracentrotus lividus, Echinodermata) and chronic growth inhibition tests with two different groups of marine microalgae (Isochrysis galbana, Haptophyta; Skeletonema costatum, Heterokontophyta) were performed with the active substance oseltamivir carboxylic acid to derive a dependable marine predicted no-effect concentration (PNEC). This was compared to a predicted environmental concentration (PEC) for oseltamivir in coastal waters, based on the worst-case freshwater PEC. The PEC/PNEC risk characterisation ratio for the marine compartment is well below 1, which in the terminology of the TGD signifies no immediate concern. Further, while oseltamivir may be persistent (P), it is not bioaccumulative (B) nor highly ecotoxic (T) and therefore not a PBT substance. In conclusion, even a high pandemic use of oseltamivir would not lead to a significant risk for the marine compartment, in confirmation of the risk assessment for sewage works and freshwaters.     

Organochlorine and heavy metals in newborns: Results from the Flemish Environment and Health Survey (FLEHS 2002–2006)

To collect regional information on internal levels of pollutants in humans in Flanders, 1196 mother–child pairs were systematically recruited in 2002–2003 via 25 maternities across Flanders. Cd, Pb, PCB congeners 118, 170, 138, 153 and 180, p,p′-DDE — a key metabolite of DDT- and hexachlorobenzene (HCB) were measured in cord blood or plasma. Cd was detected in 64% of the samples (geometric mean 0.21 µg/L cord blood). p,p′-DDE (110 ng/g plasma lipids) and Pb (14.7 µg/L blood), were measurable in nearly all samples. The individual PCB congeners could be detected in 40 to 81% of the newborns (138 + 153 + 180 = 64.4 ng/g plasma lipids). HCB (18.9 ng/g plasma lipids) and dioxin-like compounds measured by DR-CALUX® (23 pg CALUX-TEQ/g lipids) were above detection limit in more than 75% of the samples. Age and smoking habits of the mothers, did not influence the cord blood Pb and Cd levels. The organochlorines increased 4 to 9% per year of the mother's age (partial R² = 0.05 to 0.22). Mothers had 2.6% less PCBs in cord blood (partial R² = 0.02) for each unit increase in pre-pregnancy BMI. Season of delivery, breastfeeding previous children or consumption of local dairy products, were minor determinants. Up to 20% of the variability in organochlorine concentrations was explained by residence area. It was concluded that the place of birth in Flanders is an important determinant of the load of pollutants measured at the start of life. This underlines the validity of human biomonitoring on (relatively) small geographical scale.     

Hydrodynamics of the Segara Anakan lagoon

A hydrodynamic field study of the Segara Anakan lagoon combined with a reconstruction of the recorded data using a three-dimensional numerical model provides insights into the processes driving the hydrodynamics of the lagoon. This includes bathymetry, quantification of water volume fluxes with ADCP measurements, sea level recordings, salinity measurements, water budget and numerical model results for the periods of the field studies. Salinity measurements at the Klaces village show a complete flushing of the western lagoon during neap tide in the rainy season, which is assumed to increase the sedimentation. Mean salinities of the western part are in the order of 10 and 21 g/kg, while the eastern part has a larger mean salinity of 27 and 32 g/kg for the rainy and dry season, respectively. A numerical sensitivity study shows a relationship between the Citanduy discharge and the nett water volume transport between the eastern and western part of Segara Anakan. A nett transport to the west, which differs from neap to spring tides, turns to zero when Citanduy discharges are between 300 and 400 m³/s. The flushing time of the lagoon depends on the monsoon season and is about 1–3 days at the western outlet and increases to 12 days in the central parts.     

Impact of mineral components and selected trace metals on ambient PM10 concentrations

PM10 levels of the mineral components Si, Al, Fe, Ca, Mg and some trace metals were measured at three different sites in the urban area of Vienna (Austria). Observed trace metal concentrations varied between less than 0.1 ng m^?3 (Cd) and approximately 200 ng m^?3 (Zn), mineral components showed enhanced concentrations ranging from 0.01 μg m^?3 (Ca) to 16.3 μg m^?3 (Si). The contribution of the respective mineral oxides to PM10 mass concentrations accounted on average for 26.4 ± 16% (n = 1090) of the PM10 mass, with enhanced rates in spring and autumn (monthly averages of up to 40%) and decreased contributions in the cold season (monthly averages below 10%). The atmospheric occurrence of Al, Ti and Sr could be assigned to crustal sources, whereas for the elements Ba, Ca, Fe, Mg, Mn and V an increased contribution of non-crustal origin was observed. PM10 levels of As, Cd, Co, Cr, Cu, Ni, Pb, Sb, Sn and Zn were predominantly derived from man-made emissions. Intersite comparison indicated that urban PM10 mass concentrations and PM10 levels of As, Pb and Zn were predominantly influenced from the transport of aerosols from outside into the city, whereas for the elements Ba, Mg, Ca, Cu and Fe a distinctly increased impact of local emissions was observed. The contribution of these urban emissions to total PM10 concentrations was estimated by calculating the so-called “urban impact”, which was found to be 32.7 ± 18% (n = 392) in the case of PM10 mass concentrations. The investigated elements accounted on average for 31.3 ± 19% (n = 392) of the observed PM10 mass increase. The mean values for the “urban impacts” of individual elements varied between 25.5% (As) and 77.0% (Ba).     

Wood burning impact on PM10 in three Austrian regions

Anhydrosugars (levoglucosan, mannosan and galactosan) were investigated during one year in three Austrian regions at three types of sites (city-heavy traffic-impacted, city-residential and background) in order to assess the magnitude of the contribution of wood smoke to the particulate matter load and its organic fraction. The annually averaged concentrations of levoglucosan ranged from 0.12 to 0.48 μg m^?3. The levoglucosan concentration exhibited a strong annual cycle with higher concentrations in the cold season. The minor anhydrosugars had a similar annual trend, but their concentrations were lower by a factor of about 5 and about 25 in the cold season for mannosan and galactosan, respectively. Levoglucosan concentrations were higher at the inner-urban as compared to rural sites. The contribution of wood smoke to organic carbon and PM₁₀ levels was calculated using a constant ratio of levoglucosan and OC, respectively PM₁₀ as derived for fire wood typical for Alpine European regions [Schmidl, C., Marr, I.L., Caseiro, A.e, Kotianová, P., Berner, A., Bauer, H., Kasper-Giebl, A., Puxbaum, H., 2008a. Chemical characterisation of fine particle emissions from wood stove combustion of common woods growing in mid-European Alpine regions. Atmospheric Environment 42, 126–141]. The estimated contribution of wood smoke-OC to the OC of PM₁₀ ranged from one third to more than half in the cold season with higher contributions up to 70% in winter (December, January and February) in the smaller cities and the rural background. This indicates, that wood smoke is the predominant source of organic material at rural and small urban sites in central Europe. Consistently, wood smoke was an important contributor to PM₁₀ during the cold season, with contributions of around 10% in the Vienna larger region and around 20% at rural sites in the densely forested regions of Salzburg and Styria during the winter months. In those regions residential sites exhibited highest relative wood smoke contents in PM₁₀ during autumn (September till November), indicating the use of wood stoves for auxiliary heating in the transition of warm to cold season. Using the relationships between the different anhydrosugars the combustion of softwood was found to be dominant for the wood smoke occurrence in ambient air at the investigated sites. Potassium, a commonly used tracer for biomass burning, correlated well to levoglucosan, with a mass ratio of around 0.80 in the cold season.     

Degassing of H/He, CFCs and SF6 by denitrification: Measurements and two-phase transport simulations

The production of N₂ gas by denitrification may lead to the appearance of a gas phase below the water table prohibiting the conservative transport of tracer gases required for groundwater dating. We used a two-phase flow and transport model (STOMP) to study the reliability of ³H/³He, CFCs and SF₆ as groundwater age tracers under agricultural land where denitrification causes degassing. We were able to reproduce the amount of degassing (R² = 69%), as well as the ³H (R² = 79%) and ³He (R² = 76%) concentrations observed in a ³H/³He data set using simple 2D models. We found that the TDG correction of the ³H/³He age overestimated the control ³He/³He age by 2.1 years, due to the accumulation of ³He in the gas phase. The total uncertainty of degassed ³H/³He ages of 6 years (± 2 σ) is due to the correction of degassed ³He using the TDG method, but also due to the travel time in the unsaturated zone and the diffusion of bomb peak ³He. CFCs appear to be subject to significant degradation in anoxic groundwater and SF₆ is highly susceptible to degassing. We conclude that ³H/³He is the most reliable method to date degassed groundwater and that two-phase flow models such as STOMP are useful tools to assist in the interpretation of degassed groundwater age tracer data.     

The value of the environment – Is it a matter of approach?

This paper discusses why estimates of the benefits of reduced air pollution differ in accordance with the approach used. Estimates based on bottom-up studies of the damage costs related to air pollution usually turn out much lower than estimates based on assessments of the utility of reduced air pollution, obtained for instance by willingness to pay assessments. This is usually explained by the fact that the willingness to pay approach includes the utility aspect of non-market values, and for this reason, it is often preferred to the damage cost approach. This is, however, not the whole story. The paper shows why alternative approaches should not be considered as being in conflict, but rather as means to get supplementary information necessary to put a value on environmental quality. Information from bottom-up assessments of damage costs and from studies of the willingness to pay is used in a macroeconomic model to carry out an evaluation of the social costs of energy saving measures in Hungary.     

Development and verification of a toxicokinetic model of polychlorinated biphenyl elimination in persons working in a contaminated building

BACKGROUND: Polychlorinated biphenyls are toxic and slowly degrading substances that have been in widespread industrial use in the 1960s and 1970s. Despite a worldwide reduction, environmental exposure remains an issue; the assessment of an individual's level of exposure at a given time in retrospect requires valid toxicokinetic modeling of the different PCB congeners. OBJECTIVES: To develop and verify a toxicokinetic model of the in vivo-degradation of PCB 28 and 52 in adult humans. METHODS: The plasma concentrations of PCB congeners were measured in 583 persons working in a contaminated building for an average of 14.7+/-9.6 years. The values were adapted to a simple pharmacokinetic model (yt = y0 x (1 - e(-kt))); the steady state concentration y0 was estimated based on the median values of persons working exposed more than 10 years. RESULTS: The steady state concentration of PCB 28 was 0.10 microg/l, that of PCB 52 0.02 microg/l. The half-life of the congeners was estimated based on a logarithmic regression analysis according to the model mentioned above; it was 2.18 (95% CI: 1.91-2.54) years for PCB 28 and 3.95 (95% CI: 3.55-4.45) years for PCB 52, respectively. Stepwise elimination of persons with very long employment duration did not reduce the estimated half-life. CONCLUSIONS: The estimated half-life is higher than previously published data especially for PCB 52. Possible reasons and implications of this finding are discussed.