Verification of diffusive and pumped samplers for volatile organic compounds using a controlled atmosphere test facility

There is a requirement to verify the performance of sorbent-based passive or active samplers and to extend their use, where possible, to monitor volatile organic compounds (VOCs) that are known to be photochemical ozone pre-cursors or are relevant to the activities of the petrochemical industry. We report measurements of the 14-day diffusive uptake rates for the VOCs: i-butane (2-methyl propane), n-butane, i-pentane (2-methyl butane), n-pentane, n-hexane, benzene, toluene, and m-xylene (at environmental level concentrations) for industry standard axial samplers (Perkin–Elmer-type samplers) containing the sorbents Carbopack-X, -Z, -B or Tenax-TA. We also present data on back-diffusion, blank levels, and storage for the above sorbents, and describe the simultaneous use of the sorbent Carbopack-X for pumped sampling of certain VOCs. The results were obtained by dosing samplers in a controlled atmosphere test facility (CATFAC) operating under well-defined conditions of concentration, nominal temperature of 20 °C, wind speed of 0.5 m s^?1, and relative humidities of 0% and 80%. Field measurements were also obtained to provide supplementary data to support the laboratory study. Results are compared to existing published data, where these are available.     

Analysis of 3-year observations of CFC-11, CFC-12 and CFC-113 from a semi-rural site in China

In-situ measurements of atmospheric chlorofluorocarbons (CFCs) can be used to the assess their global and regional emissions and to check for compliance with phase-out schedules under Montreal protocol and its amendments. The atmospheric mixing ratios of CFC-11 (CCl₃F), CFC-12 (CCl₂F₂) and CFC-113 (CCl₂F–CClF₂) have been measured by an automated in-situ GC-ECDs system at the regional Chinese Global Atmosphere Watch (GAW) station Shangdianzi (SDZ), from November 2006 to October 2009. The time series for these three principal CFCs showed large episodic events and background conditions occurred for approximately 30% (CFC-11), 52% (CFC-12) and 56% (CFC-113) of the measurements. The mean background mixing ratios for CFC-11, CFC-12 and CFC-113 were 244.8 ppt (parts per trillion, 10^?12, molar) 539.6 ppt and 76.8 ppt, respectively, for 2006–2009. The enhanced CFC mixing ratios compared to AGAGE sites such as Trinidad Head (THD), US and Mace Head (MHD), Ireland suggest regional influences even during background conditions at SDZ, which is much closer to highly-populated areas. Between 2006 and 2009 background CFCs exhibited downward trends at rates of ?2.0 ppt yr^?1 for CFC-11, ?2.5 ppt yr^?1 for CFC-12 and ?0.7 ppt yr^?1 for CFC-113. De-trended 3-year average background seasonal cycles displayed small fluctuations with peak-to-trough amplitudes of 1.0 ± 0.02 ppt (0.4%) for background CFC-11, 1.3 ± 2.1 ppt (0.3%) for CFC-12 and 0.2 ± 0.4 ppt (0.3%) for CFC-113. On the other hand, during pollution periods these CFCs showed much larger seasonal cycles of 11.2 ± 10.7 ppt (5%) for CFC-11, 7.5 ± 6.5 ppt (2%) for CFC-12 and 1.0 ± 1.2 ppt (1.2%) for CFC-113, with apparent winter minima and early summer maxima. This enhancement was attributed to prevailing wind directions from urban regions in summer and to enhanced anthropogenic sources during the warm season. In general, horizontal winds from northeast showed negative contribution to atmospheric CFCs loading, whereas South Western advection (urban sector: Beijing) had positive contributions.     

Contribution of transition metals in the reactive oxygen species activity of PM emissions from retrofitted heavy-duty vehicles

We assessed the contribution of water-soluble transition metals to the reactive oxygen species (ROS) activity of diesel exhaust particles (DEPs) from four heavy-duty vehicles in five retrofitted configurations (V-SCRT, Z-SCRT, DPX, hybrid, and school bus). A heavy-duty truck without any control device served as the baseline vehicle. Particles were collected from all vehicle-configurations on a chassis dynamometer under three driving conditions: cruise (80 km h^?1), transient UDDS, and idle. A sensitive macrophage-based in vitro assay was used to determine the ROS activity of collected particles. The contribution of water-soluble transition metals in the measured activity was quantified by their removal using a Chelex^® complexation method. The study demonstrates that despite an increase in the intrinsic ROS activity (per mass basis) of exhaust PM with use of most control technologies, the overall ROS activity (expressed per km or per h) was substantially reduced for retrofitted configurations compared to the baseline vehicle. Chelex treatment of DEPs water extracts removed a substantial (≥70%) and fairly consistent fraction of the ROS activity, which ascertains the dominant role of water-soluble metals in PM-induced cellular oxidative stress. However, relatively lower removal of the activity in few vehicle-configurations (V-SCRT, DPX and school bus idle), despite a large aggregate metals removal, indicated that not all species were associated with the measured activity. A univariate regression analysis identified several transition metals (Fe, Cr, Co and Mn) as significantly correlated (R > 0.60; p < 0.05) with the ROS activity. Multivariate linear regression model incorporating Fe, Cr and Co explained 90% of variability in ROS levels, with Fe accounting for the highest (84%) fraction of the variance.     

Information system for monitoring environmental impacts of genetically modified organisms

Background, aim and scope  

European legislation stipulates that genetically modified organisms (GMO) have to be monitored to identify potential adverse environmental effects. A wealth of different types of monitoring data from various sources including existing environmental monitoring programmes is expected to accumulate. This requires an information system to efficiently structure, process and evaluate the monitoring data.     

Evaluating the impact of fractures on the performance of the In Salah CO2 storage site

The In Salah Gas Joint Venture CO₂ storage project has been in operation in Algeria since 2004 and is currently the world's largest onshore CO₂ storage project. CO₂ is injected into the saline aquifer of a gas reservoir several kilometres away from the gas producers. Current focus in the project is on implementing a comprehensive monitoring strategy and modelling the injection behaviour in order to ensure and verify safe long-term storage. A key part of this effort is the understanding of the processes involved in CO₂ migration within relatively low-permeability sandstones and shales influenced by fractures and faults. We summarise our current understanding of the fault and fracture pattern at this site and show preliminary forecasts of the system performance using discrete fracture models and fluid flow simulations. Despite evidence of fractures at the reservoir/aquifer level, the thick mudstone caprock sequence is expected to provide an effective flow and mechanical seal for the storage system; however, quantification of the effects of fracture flow is essential to the site verification.     

Dealing with disjunct concentration measurements in eddy covariance applications: A comparison of available approaches

Using proton transfer reaction mass spectrometry equipped with a quadrupol mass analyser to quantify the biosphere-atmosphere exchange of volatile organic compounds (VOC), concentrations of different VOC are measured sequentially. Depending on how many VOC species are targeted and their respective integration times, each VOC is measured at repeat rates on the order of a few seconds. This represents an order of magnitude longer sample interval compared to the standard eddy covariance (EC) method (5–20 Hz sampling rates). Here we simulate the effect of disjunct sampling on EC flux estimates by decreasing the time resolution of CO₂ and H₂O concentrations measured at 20 Hz above a temperate mountain grassland in the Austrian Alps. Fluxes for one month are calculated with the standard EC method and compared to fluxes calculated based on the disjunct data (1, 3 and 5 s sampling rates) using the following approaches: i) imputation of missing concentrations based on the nearest neighbouring samples (iDEC_nn), ii) imputation by linear interpolation (iDEC_li), and iii) virtual disjunct EC (vDEC), i.e. flux calculation based solely on the disjunct concentrations. It is shown that the two imputation methods result in additional low-pass filtering, longer lag times (as determined with the maximum cross-correlation method) and a flux loss of 3–30% as compared to the standard EC method. A novel procedure, based on a transfer function approach, which specifically corrects for the effect of data treatment, was developed, resulting in improved correspondence (to within 2%). The vDEC method yields fluxes which approximate the true (20 Hz) fluxes to within 3–7% and it is this approach we recommend because it involves no additional empirical corrections. The only drawback of the vDEC method is the noisy nature of the cross-correlations, which poses problems with lag determination – practical approaches to overcome this limitation are discussed.     

A Generic Bio-Economic Farm Model for Environmental and Economic Assessment of Agricultural Systems

Bio-economic farm models are tools to evaluate ex-post or to assess ex-ante the impact of policy and technology change on agriculture, economics and environment. Recently, various BEFMs have been developed, often for one purpose or location, but hardly any of these models are re-used later for other purposes or locations. The Farm System Simulator (FSSIM) provides a generic framework enabling the application of BEFMs under various situations and for different purposes (generating supply response functions and detailed regional or farm type assessments). FSSIM is set up as a component-based framework with components representing farmer objectives, risk, calibration, policies, current activities, alternative activities and different types of activities (e.g., annual and perennial cropping and livestock). The generic nature of FSSIM is evaluated using five criteria by examining its applications. FSSIM has been applied for different climate zones and soil types (criterion 1) and to a range of different farm types (criterion 2) with different specializations, intensities and sizes. In most applications FSSIM has been used to assess the effects of policy changes and in two applications to assess the impact of technological innovations (criterion 3). In the various applications, different data sources, level of detail (e.g., criterion 4) and model configurations have been used. FSSIM has been linked to an economic and several biophysical models (criterion 5). The model is available for applications to other conditions and research issues, and it is open to be further tested and to be extended with new components, indicators or linkages to other models.     

Reduction of Baltic Sea Nutrient Inputs and Allocation of Abatement Costs Within the Baltic Sea Catchment

The Baltic Sea Action Plan (BSAP) requires tools to simulate effects and costs of various nutrient abatement strategies. Hierarchically connected databases and models of the entire catchment have been created to allow decision makers to view scenarios via the decision support system NEST. Increased intensity in agriculture in transient countries would result in increased nutrient loads to the Baltic Sea, particularly from Poland, the Baltic States, and Russia. Nutrient retentions are high, which means that the nutrient reduction goals of 135 000 tons N and 15 000 tons P, as formulated in the BSAP from 2007, correspond to a reduction in nutrient loadings to watersheds by 675 000 tons N and 158 000 tons P. A cost-minimization model was used to allocate nutrient reductions to measures and countries where the costs for reducing loads are low. The minimum annual cost to meet BSAP basin targets is estimated to 4.7 billion €.     

A review of plant–pharmaceutical interactions: from uptake and effects in crop plants to phytoremediation in constructed wetlands

Pharmaceuticals are commonly found both in the aquatic and the agricultural environments as a consequence of the human activities and associated discharge of wastewater effluents to the environment. The utilization of treated effluent for crop irrigation, along with land application of manure and biosolids, accelerates the introduction of these compounds into arable lands and crops. Despite the low concentrations of pharmaceuticals usually found, the continuous introduction into the environment from different pathways makes them ‘pseudo-persistent’. Several reviews have been published regarding the potential impact of veterinary and human pharmaceuticals on arable land. However, plant uptake as well as phytotoxicity data are scarcely studied. Simultaneously, phytoremediation as a tool for pharmaceutical removal from soils, sediments and water is starting to be researched, with promising results. This review gives an in-depth overview of the phytotoxicity of pharmaceuticals, their uptake and their removal by plants. The aim of the current work was to map the present knowledge concerning pharmaceutical interactions with plants in terms of uptake and the use of plant-based systems for phytoremediation purposes.