Effects of fly ash addition on physical properties of porous clay-fly ash composites via polymeric replica technique

The porous composites of clay and fly ash have the potential to be used in many fields, such as catalyst support and gas adsorbents. In this study, various ratios of fly ash (1–2) with different percentage of suspension (50–70 wt%) were applied to produce porous clay-fly ash composites via polymeric replica technique. Fabrication process starts by mixing clay and fly ash in distilled water to form slurry. The process is followed by fully immersing polymer sponge in slurry. The excess slurry is then removed through squeezing. Finally, the sponge coated with slurry is sintered at 500 and 1250 °C for 1 h. It is found that the compressive strength of porous composites improves significantly (0.178–1.28 MPa) when the amount of clay-fly ash suspension mixture (50–70 wt%) increases. The compressive strength of porous composites is mainly attributed to the mullite, quartz and amorphous phase formations. These results are supported by X-ray diffraction analysis. On the other hand, increase in the amount of suspension reduces the apparent density (from 2.44 to 2.32 g/cm³) and porosity (from 97 to 85 %). The reduction in apparent density is believed to be caused by the presence of high fly ash content in porous composites. The melted fly ash cenospheres have closed the internal pores and increased density of samples. Higher suspension level not only reduces porosity, but also increases close pores of the porous composites. The results are justified through the observation from the structures of porous clay-fly ash composites.     

Conversion of CCA-treated wood to ethanol: a method to reduce leaching of metals from disposed treated wood prior to disposal

The objective of this paper is to evaluate the feasibility of producing ethanol from CCA-treated wood that is highly leachable. Following the initial tests, CCA-treated wood was hydrolysed and fermented and the results showed not only that ethanol was produced during the fermentation process but that metals were taken up by the yeast. Toxicity characteristic leaching procedure tests of the hydrolysed wood leached less than 4 mg/L of As while minimal amounts of Cr and Cu remained in the hydrolysed wood which makes landfilling of hydrolysed wood acceptable and less hazardous. A slightly lower amount of ethanol from CCA-treated than untreated wood was produced (6 and 7 g/L, respectively). In general, it suggests that production of ethanol as a source of energy from a hazardous waste (CCA-treated wood) is feasible.     

Contaminant mass flux and forensic assessment of polycyclic aromatic hydrocarbons: Tools to inform remediation decision making at a contaminated site in Canada

Polycyclic aromatic hydrocarbons (PAHs) and metal(loid) mass flux estimates and forensic assessment using PAH diagnostic ratios were used to inform remediation decision making at the Sydney Tar Ponds (STPs) and Coke Ovens cleanup project in eastern Canada. Environmental effects monitoring of surface marine sediments in Sydney Harbor indicated significantly higher PAH concentrations during the first year of remediation monitoring compared to baseline. This was equivalent to PAH loadings of ～2,000 kg over a 15‐month period. Increases in sediment PAH concentrations raised serious concerns for regulators, who requested cessation of remediation activities early in the $400 M (CAD) project. Historically, the STPs were reported as the primary source of PAH contamination in Sydney Harbor with estimated discharges of 300 to 800 kg/year between 1989 and 2001. Mass flux estimates of PAHs and metal(loid)s and PAH diagnostic ratios were used to evaluate if increases in PAH concentrations in marine sediments were the result of the STPs remediation activities. PAH mass flux estimates approximated that 17 to 97 kg/year were discharged from the STPs during three years of remediation and were corroborated by an independent PAH flux estimate of 119 kg in year 1. PAH fluxes to the Sydney Harbor were mostly surface water derived, with groundwater contributing negligible quantities (0.002–0.005 kg/year). Fluxes of metal(loid)s to harbor sediments were stable or declining across all years and were mirrored in sediment metal(loid) concentrations, which lacked temporal variation, unlike total PAH concentrations. Flux results were also corroborated using PAH diagnostic ratios, which found a common source of PAHs. Coal combustion was likely the principal source of PAHs and not migration from the STPs during remediation. Although short‐term residual sediment PAH increases during onset of remediation raised concerns for regulators, calls for premature cessation of remediation early in the project were unwarranted based on only one year of monitoring data. Mass flux estimates and forensic assessments using PAH diagnostic ratios proved useful tools to inform remediation decision making that helped environmental protection and reduced costs associated with lost cleanup time.     

Towards an international standard: The ISO/DIS 18504 standard on sustainable remediation

Sustainable remediation is the elimination and/or control of unacceptable risks in a safe and timely manner while optimizing the environmental, social, and economic value of the work. Forthcoming International Organization for Standardization (ISO) Standard on Sustainable Remediation will allow countries without the capacity to develop their own guidance to benefit from work done over the past decade by various groups around the world. The ISO standard has progressed through the committee draft (ISO/CD 18504) and draft international standard (ISO/DIS 18504) stages. The risk‐based approach to managing the legacy of historically contaminated soil and groundwater has been incorporated into policy, legislation, and practice around the world. It helps determine the need for remediation and the end point of such remediation. Remediation begins with an options appraisal that short lists strategies that could deliver the required reduction in risk. A remediation strategy comprises one or more remediation technologies that will deliver the safe and timely elimination and/or control of unacceptable risks. The ISO standard will help assessors identify the most sustainable among the shortlisted, valid alternative remediation strategies. Practitioners presenting case studies claiming to constitute sustainable remediation should now report how they have aligned their work with the new standard. Indicators are used to compare alternative remediation strategies. The simplest metric that allows a characteristic to act as an indicator should be chosen. Weightings indicators can become a contested exercise and should only be undertaken where there is a clear desire for it by stakeholders and a clear need for it in identifying a preferred strategy. The simplest means of ranking alternative remediation strategies should be adopted.     

Prenatal diagnosis of cystinosis utilizing chorionic villus sampling

The prenatal diagnosis of cystinosis is currently based on the increased amount of free-cystine present in amniotic fluid cells. Amniocyte cultures must be grown for at least 2 weeks to obtain sufficient cells for such measurements. Thus, the diagnosis cannot be made until close to 20 weeks gestational age by this method. We report a case in which chorionic villi were used for direct cystine measurement resulting in the in utero diagnosis of cystinosis at 9 weeks gestational age. The diagnosis was confirmed by the study of cultured chorionic villus cells, and of the 10-week abortus.     

Biomonitoring of heavy metals by pollen in urban environment

Abstract Industrial development and consumption of petroleum products leads to increase air pollution levels especially in urban and industrial areas. Heavy metal components associated with air pollutants have far reaching effects with respect to economic and ecological importance of pollens. The pollens are male reproductive organs of the plant and travel through air from flower to flower for pollination purpose. During this period they are exposed to air pollutants. Present investigation thus pertains to study of effect of air pollutants on pollens especially biosorption and bioaccumulation of heavy metals. The pollens of three commonly occurring plants namely Cassia siamea, Cyperus rotundus, Kigelia pinnata have been studied from the NH-6 of Nagpur city, India. The pollens exposed to polluted air showed the presence of higher concentrations of Ca, Al and Fe as compared to unexposed pollens. Higher concentration of these metals was observed in Cyperus rotundus followed by Cassia siamea and Kigelia pinnata. These results indicate that pollens act as good indicator of air pollution giving results in short time of exposure of 5–10 h. Apart from this, it is also reported that some of these metals play crucial role in the metabolic activity in pollens for example Calcium is necessary for growth of pollen tube and other metabolic activities in pollens. The presence of these metals in pollens may also enhance the allergenicity of the pollens. Similarly accumulation of heavy metals may also deteriorate the quality of pollen for their economical use. The viability of pollen is also affected by these pollutants in sensitive species leading to impairment of their fertility.     

Soil contamination of heavy metals in the Katedan Industrial Development Area, Hyderabad, India

Studies on quantitative soil contamination due to heavy metals were carried out in Katedan Industrial Development Area (KIDA), south of Hyderabad, Andhra Pradesh, India under the Indo-Norwegian Institutional Cooperation Programme. The study area falls under a semi-arid type of climate and consists of granites and pegmatite of igneous origin belonging to the Archaean age. There are about 300 industries dealing with dyeing, edible oil production, battery manufacturing, metal plating, chemicals, etc. Most of the industries discharge their untreated effluents either on open land or into ditches. Solid waste from industries is randomly dumped along roads and open grounds. Soil samples were collected throughout the industrial area and from downstream residential areas and were analysed by X-ray Fluorescence Spectrometer for fourteen trace metals and ten major oxides. The analytical data shows very high concentrations of lead, chromium, nickel, zinc, arsenic and cadmium through out the industrial area. The random dumping of hazardous waste in the industrial area could be the main cause of the soil contamination spreading by rainwater and wind. In the residential areas the local dumping is expected to be the main source as it is difficult to foresee that rain and wind can transport the contaminants from the industrial area. If emission to air by the smokestacks is significant, this may contribute to considerable spreading of contaminants like As, Cd and Pb throughout the area. A comparison of the results with the Canadian Soil Quality Guidelines (SQGL) show that most of the industrial area is heavily contaminated by As, Pb and Zn and local areas by Cr, Cu and Ni. The residential area is also contaminated by As and some small areas by Cr, Cu, Pb and Zn. The Cd contamination is detected over large area but it is not exceeding the SQGL value. Natural background values of As and Cr exceed the SQGL values and contribute significantly to the contamination in the residential area. However, the availability is considerably less than anthropogenic contaminants and must therefore be assessed differently. The pre- and post-monsoon sampling over two hydrological cycles in 2002 and 2003 indicate that the As, Cd and Pb contaminants are more mobile and may expect to reach the groundwater. The other contaminants seem to be much more stable. The contamination is especially serious in the industrial area as it is housing a large permanent residing population. The study not only aims at determining the natural background levels of trace elements as a guide for future pollution monitoring but also focuses on the pollution vulnerability of the watershed. A plan of action for remediation is recommended.     

Air quality and deposition of trace elements in Didouche Mourad, Algeria

Total suspended particulate matter and deposition fluxes of particles were investigated in the town of Didouche Mourad which is located 13 km north of Constantine. Samples of air particulate matter were collected at one site located in the heart of the town and situated 3 km north of a cement plant. Samples were collected from 2 November 2002 to 28 April 2003 every 3 days using a high volume air sampler. Sampling intervals were 24 h in all cases. During the same period, samples of dust fallout were collected at the same site. Samples were collected at 30-day intervals. Lead, chromium, manganese, nickel, copper, cobalt and cadmium deposition fluxes were measured and both the soluble and insoluble fractions were determined. Furthermore, the information gathered by this study was correlated with the corresponding hourly weather data provided by a weather station installed at the study station. The possible sources for dust and trace metals were analyzed by comparing average contributions of wind aspects to the concentrations and depositions of mass and chemical species with the average frequencies of wind direction. The mean concentration was 300 μg/m³. The average dust deposition rate through the period of study was 221 mg/(m².day). Results indicate that anthropogenic sources contribute greatly to trace elements. An exposure assessment to the heavy metals taking into account the inhalation route and soil dust ingestion was carried out and allowed direct comparison of trace metal intakes via these routes.     

Indoor and outdoor PM mass and number concentrations at schools in the Athens area

Simultaneous indoor and outdoor PM₁₀ and PM_2.5 concentration measurements were conducted in seven primary schools in the Athens area. Both gravimetric samplers and continuous monitors were used. Filters were subsequently analyzed for anion species. Moreover ultrafine particles number concentration was monitored continuously indoors and outdoors. Mean 8-hr PM₁₀ concentration was measured equal to 229 ± 182 μg/m³ indoors and 166 ± 133 μg/m³ outdoors. The respective PM_2.5 concentrations were 82 ± 56 μg/m³ indoors and 56 ± 26 μg/m³ outdoors. Ultrafine particles 8-h mean number concentration was measured equal to 24,000 ± 17,900 particles/cm³ indoors and 32,000 ± 14,200 particles/cm³ outdoors. PM₁₀ outdoor concentrations exhibited a greater spatial variability than the corresponding PM_2.5 ones. I/O ratios were close or above 1.00 for PM₁₀ and PM_2.5 and smaller than 1.00 for ultrafine particles. Very high I/O ratios were observed when intense activities took place. The initial results of the chemical analysis showed that accounts for the 6.6 ± 3.5% of the PM₁₀ and for the 3.1 ± 1.4%.The corresponding results for PM_2.5 are 12.0 ± 7.7% for and 3.1 ± 1.9% for . PM_2.5 indoor concentrations were highly correlated with outdoor ones and the regression line had the largest slope and a very low intercept, indicative of no indoor sources of fine particulate . The results of the statistical analysis of indoor and outdoor concentration data support the use of as a proper surrogate for indoor PM of outdoor origin.     

Whole body vibration exposure in heavy earth moving machinery operators of metalliferrous mines

As mining operations get mechanized, the rate of profit generation increases and so do the rate of occupational hazards. This study deals with one such hazard - occupational vibration. The present study was carried out to determine the whole body vibration (WBV) exposure of the heavy earth moving machinery (HEMM) operators in two types of metalliferous mines in India, when they were engaged in the mining activity. Cross-comparison was done of the vibration dose value (VDV) for HEMM operators as well as each type of mine. The VDV for the shovel operator in bauxite mine was observed to be 13.53 +/- 5.63 m/s(7/4) with 25% of the readings higher than the prescribed limit whereas in iron ore mine VDV for dumper operator was 10.81 +/- 3.44 m/s(7/4) with 14.62% readings on the higher side. Cross-comparison of the VDV values for bauxite and iron ore mines revealed that it was 9.57 +/- 4.93 and 8.21 +/- 5.12 m/s(7/4) with 21.28 and 14.95% of the readings on the higher side respectively. The Student's t test level was found to be insignificant for both type of mines, indicating that the WBV exposure is not dependent on the type of mine but is dependent on the working condition and type of HEMM in operation.