Soil sampling and analysis for volatile organic compounds

Concerns over data quality have raised many questions related to sampling soils for volatile organic compounds (VOCs). This paper was prepared in response to some of these questions and concerns expressed by Remedial Project Managers (RPMs) and On-Scene Coordinators (OSCs). The following questions are frequently asked:

1. Is there a specific device suggested for sampling soils for VOCs?
2. Are there significant losses of VOCs when transferring a soil sample from a sampling device (e.g., split spoon) into the sample container?
3. What is the best method for getting the sample from the split spoon (or other device) into the sample container?
4. Are there smaller devices such as subcore samplers available for collecting aliquots from the larger core and efficiently transferring the sample into the sample container?
5. Are certain containers better than others for shipping and storing soil samples for VOC analysis?
6. Are there any reliable preservation procedures for reducing VOC losses from soil samples and for extending holding times?

Guidance is provided for selecting the most effective sampling device for collecting samples from soil matrices. The techniques for sample collection, sample handling, containerizing, shipment, and storage described in this paper reduce VOC losses and generally provide more representative samples for volatile organic analyses (VOA) than techniques in current use. For a discussion on the proper use of sampling equipment the reader should refer to other sources (Acker, 1974; U.S. EPA, 1983; U.S. EPA, 1986a). Soil, as referred to in this report, encompasses the mass (surface and subsurface) of unconsolidated mantle of weathered rock and loose material lying above solid rock. Further, a distinction must be made as to what fraction of the unconsolidated material is soil and what fraction is not. The soil component here is defined as all mineral and naturally occurring organic material that is 2 mm or less in size. This is the size normally used to differentiate between soils (consisting of sands, silts, and clays) and gravels. Although numerous sampling situations may be encountered, this paper focuses on three broad categories of sites that might be sampled for VOCs:

1. Open test pit or trench.
2. Surface soils (<5 ft in depth).
3. Subsurface soils (>5 ft in depth).

     

Woodstove emission measurement methods: Comparison and emission factors update

On February 26, 1988, the U.S. Environmental Protection Agency promulgated Standards of Performance for residential wood heaters, or woodstoves. Over the past several years, a number of field studies have been undertaken to determine the actual level of emission reduction achieved by new technology woodstoves in everyday use. These studies have required the development and use of particulate and gaseous emission sampling equipment compatible with operation in private houses. Since woodstoves are tested for certification in the laboratory using EPA Methods 5G and 5H, it is of substantial interest to determine the correlation between these regulatory methods and the in-house equipment. Two in-house sampling systems have been used most widely. One is an intermittent, pump-driven particulate sampler which collects particulate and condensable organics on a filter and organic adsorbent resin. Oxygen concentration is measured by a sensor in the sample line. The sampler is controlled by a data logger which also records other parameters of interest. The second system uses an evacuated cylinder as the motive force. Particulate and condensable organics are collected in a condenser and dual filter. The sampler operates continuously whenever the stack temperature is above the set point. Average stack gas concentrations are measured from the evacuated cylinder at the conclusion of the sampling period. Both samplers were designed to operate unattended for 1-week periods. A large number of tests have been run comparing Methods 5G and 5H to both of the field samplers. This paper presents these comparison data and determines the relationships between laboratory certification sampling methods and field samplers.     

Analysing the sensitivity behaviour of two hydrology models

Recently, the New Morris Method has been presented as an effective sensitivity analysis tool for mathematical models. The New Morris Method estimates the sensitivity of an output parameter to a given set of input parameters (first-order effects) and the extent these parameters interact with each other (second-order effects). This method requires the specification of two parameters (runs and resolution) that control the sampling of the output parameter to determine its sensitivity to various inputs. The criteria for these parameters have been set on the analysis of a well-behaved analytical function (see Cropp and Braddock, Reliab. Eng. Syst. Saf. 78:77–83, 2002), which may not be applicable to other physical models that describe complex processes. This paper will investigate the appropriateness of the criteria from (Cropp and Braddock, 2002) and hence the effectiveness of the New Morris Method to determine the sensitivity behaviour of two hydrologic models: the Soil Erosion and Deposition System and Griffith University Representation of Urban Hydrology. In the first case, this paper will separately analyse the sensitivity of an output parameter on a set of input parameters (first- and second-order effects) for each model and discuss the physical meaning of these sensitivities. This will be followed by an investigation into the sampling criteria by exploring the convergence of the sensitivity behaviour for each model as the sampling of the parameter space is increased. By comparing these trends to the convergence behaviour from Cropp and Braddock (2002), we will determine how well the New Morris Method estimates the sensitivity for each model and whether the sampling criteria are appropriate for these models. It will be shown that the New Morris Method can provide additional insight into the functioning of these models, and that, under a different metric, the sensitivity behaviour of these models does converge confirming the sampling criteria set by Cropp and Braddock.     

Application of cryofocusing hydride generation and atomic fluorescence detection for dissolved mercury species determination in natural water samples

The concentration levels of mercury (Hg) species in natural water samples are usually low. Consequently, accurate analysis with low detection limits is still a major problem. In this work, a method was applied for the simultaneous direct determination of dissolved mercury species in water samples by on-line hydride generation (HG), cryogenic trapping (CT), gas chromatography (GC) and detection by atomic fluorescence spectrometry (AFS). The suitability of the method for real samples with different organic matter and chloride contents was evaluated by recovery experiments in synthetic and natural spiked water samples. The HG method was compared with other current available methods for mercury analysis with respect to the different fraction of mercury analysed, i.e. 'reactive', 'reducible' or total. HG derivatization and SnCl2 reduction (with and without previous oxidation with BrCl) were applied to synthetic and natural (spiked and non-spiked) water samples. The influence of chloride and dissolved organic matter concentrations was studied. The results suggest that the HG procedure is suitable for the simultaneous determination of Hg2+ and MeHg+ in surface water samples. Inorganic mercury analysed by HG (i.e. reducible) is close to the total inorganic mercury.     

The efficacy of protoporphyrin as a predictive biomarker for lead exposure in canvasback ducks: Effect of sample storage time

We used 363 blood samples collected from wild canvasback dueks (Aythya valisineria) at Catahoula Lake, Louisiana, U.S.A. to evaluate the effect of sample storage time on the efficacy of erythrocytic protoporphyrin as an indicator of lead exposure. The protoporphyrin concentration of each sample was determined by hematofluorometry within 5 min of blood collection and after refrigeration at 4 °C for 24 and 48 h. All samples were analyzed for lead by atomic absorption spectrophotometry. Based on a blood lead concentration of 0.2 ppm wet weight as positive evidence for lead exposure, the protoporphyrin technique resulted in overall error rates of 29%, 20%, and 19% and false negative error rates of 47%, 29% and 25% when hematofluorometric determinations were made on blood at 5 min, 24 h, and 48 h, respectively. False positive error rates were less than 10% for all three measurement times. The accuracy of the 24-h erythrocytic protoporphyrin classification of blood samples as positive or negative for lead exposure was significantly greater than the 5-min classification, but no improvement in accuracy was gained when samples were tested at 48 h. The false negative errors were probably due, at least in part, to the lag time between lead exposure and the increase of blood protoporphyrin concentrations. False negatives resulted in an underestimation of the true number of canvasbacks exposed to lead, indicating that hematofluorometry provides a conservative estimate of lead exposure.The U.S. Government's right to retain a non-exclusive, royalty-free licence in and to any copyright is acknowledgedDeceased     

Suspended particulates and bioaerosols emitted from an agricultural non-point source

Suspended particulate and bioaerosol levels were measured at three sites downwind of an agricultural non-point source during the wheat harvesting season. Suspended particulates were detected at mean values ranging from 10000 to 2420 micrograms m-3 at distances of from 20 to 60 m downwind of the source, respectively. Airborne viable bacterial counts were recorded at mean values ranging between 10(4) and 10(6) colony forming units (cfu) m-3, whereas, Gram negative (Gram -ve) bacteria varied between 10(3) and 10(5) cfu m-3. Fungi levels were detected at mean values varying between 10(5) and 10(6) cfu m-3. However, streptomycetes were found at lower counts than those recorded for viable bacteria and fungi. Total viable bacteria, Gram -ve bacteria, fungi and streptomycetes associated hay fragments were determined at mean values of 1.5 x 10(6), 1.6 x 10(3), 2.2 x 10(4) and 6 x 10(3) cfu g-1 of hay, respectively. Cladosporium, white and red yeasts as well as Alternaria were the predominant airborne fungi, whereas, Alternaria was the dominant species associated with hay fragments. Pseudomonas, Acinetobacter and Enterobacteriaceae were the dominant Gram -ve bacteria. The most common fungal genera, such as Cladosporium and Fusarium (minor short axis), as well as Streptomyces species have an aerodynamic diameter (dae) of less than 5 microns, which can penetrate and deposit in the alveoli. Farmers and nearby residents are exposed to high levels of organic dust and bioaerosols during the wheat harvesting season. This may cause health problems in exposed persons based on toxic or allergic reactions.     

Control of rumen methanogenesis

During the last decades, considerable research on methane production in the rumen and its inhibition has been carried out. Initially, as methane production represents a significant loss of gross energy in the feed (2–15%), the ultimate goal of such intervention in rumen fermentation was an increase in feed efficiency. A second reason favouring research on methane inhibition is its role in the global warming phenomenon and in the destruction of the ozone layer. In this review, the authors describe briefly several interventions for reducing methane emission by ruminants. The objective can be reached by intervention at the dietary level by ration manipulation (composition, feeding level) or by the use of additives or supplements. Examples of additives are polyhalogenated compounds, ionophores and other antibiotics. Supplementation of the ration with lipids also lowered methanogenesis. More biotechnological interventions, e.g., defaunation, probiotics and introduction of reductive acetogenesis in the rumen, are also mentioned. It can be concluded that drastic inhibition of methane production is not unequivocally successful as a result of several factors, such as: instantaneous inhibition often followed by restoration of methanogenesis due to adaptation of the microbes or degradation of the additive, toxicity for the host animal, negative effects on overall digestion and productive performance. Therefore, methanogenesis and its inhibition cannot be considered as a separate part of rumen fermentation and its consequences on the animal should be taken into account.     

A simple,cost-effective multispecies toxicity test using organisms with a cosmopolitan distribution

Difficulties in making accurate, ecosystem-level predictions of environmental effects of chemicals, mixtures, and effluents based solely on the results of tests on single species have necessitated the development of more environmentally realistic, predictive testing methods. This paper describes a multispecies, community-level toxicity test based on the colonization of artificial substrates by microbial species. Tests examined the colonization of initially barren polyurethane foam artificial substrates by Protozoa from a species source colonized in a natural system. Differences in colonization were examined in microecosystems amended with low levels of cadmium, a very toxic heavy metal, and TFM, an organic biocide used against larval sea lamprey. Tests examined differences in colonization over 28 days. For cadmium, effect levels were estimated to be near 1 g 1^–1, in the low range of effect levels determined from chronic single species tests. For TFM, effect levels were estimated to be between 1 and 10 ppm, overlapping the concentrations used in environmental applications. The colonization response, which depends on naked microbial cells reproducing and migrating through toxicant amended water to new substrates, is very sensitive. Tests based on colonization can be adapted to use species from a target receiving system or can use species from a designated natural source. Field validation of these tests can employ nearly identical methods to those used in laboratory studies to assess the accuracy of predictions based on test system data.     

The analysis of monitoring data with the aid of time-series analysis

Methods derived from time-series analysis are proposed for processing monitoring data. The necessity for the use of these methods is demonstrated. In a case study time-series analysis was applied to assess the impact of the closure of the Grevelingen estuary (S. W. Netherlands) in 1971 on a local wintering population of Oystercatchers (Haematopus ostralegus) in the adjacent Oosterschelde estuary.Communication No. 328 of the Delta Institute for Hydrobiological Research.     

A study on the behaviour of pesticides and their transformation products in the Scheldt estuary using liquid chromatography-electrospray tandem mass spectrometry

Off-line solid-phase extraction (SPE) combined with liquid chromatography-electrospray tandem mass spectrometry (LC-ESI-MS-MS) was used to study the estuarine behaviour of the polar pesticides, atrazine, chloridazon, diuron and metolachlor, and their transformation products (TPs), hydroxyatrazine (HA), desisopropylatrazine (DIA), desethylatrazine (DEA), 3,4-dichlorophenylmethylurea (DPMU) and monuron. The compounds were identified by comparing their LC retention times and product-ion spectra with those of standard solutions. In all but one case the detection limits of the method were sufficient to determine the compounds of interest over the entire salinity range in the estuary. The concentrations of the dissolved pesticides ranged from 70 ng l-1 for chloridazon to 1350 ng l-1 for diuron. The levels of TPs were 3-8% of the levels of their parent pesticide. The mixing plots of polar pesticides and their TPs indicated that TPs, which are present in fresh river water, are conservatively transported to the sea and that no additional amounts of TPs are formed during their transport through the estuary. The one exception was HA, of which approximately 10% of the amount transported to the North Sea is formed in the lower part of the estuary by photochemical oxidation of atrazine. The latter was concluded from the ratios of each analyte over the sum total of the parent pesticide and all TPs along the salinity gradient, which proved to be a useful tool for identifying such estuarine transformations.