Mass balances and life cycle inventory of home composting of organic waste

A comprehensive experimental setup with six single-family home composting units was monitored during 1 year. The composting units were fed with 2.6-3.5 kg organic household waste (OHW) per unit per week. All relevant consumptions and emissions of environmental relevance were addressed and a full life-cycle inventory (LCI) was established for the six home composting units. No water, electricity or fuel was used during composting, so the major environmental burdens were gaseous emissions to air and emissions via leachate. The loss of carbon (C) during composting was 63-77% in the six composting units. The carbon dioxide (CO(2)) and methane (CH(4)) emissions made up 51-95% and 0.3-3.9% respectively of the lost C. The total loss of nitrogen (N) during composting was 51-68% and the nitrous oxide (N(2)O) made up 2.8-6.3% of this loss. The NH(3) losses were very uncertain but small. The amount of leachate was 130 L Mg(-1) wet waste (ww) and the composition was similar to other leachate compositions from home composting (and centralised composting) reported in literature. The loss of heavy metals via leachate was negligible and the loss of C and N via leachate was very low (0.3-0.6% of the total loss of C and 1.3-3.0% of the total emitted N). Also the compost composition was within the typical ranges reported previously for home composting. The level of heavy metals in the compost produced was below all threshold values and the compost was thus suitable for use in private gardens.     

Bioconversion of dairy manure by black soldier fly (Diptera: Stratiomyidae) for biodiesel and sugar production

Modern dairies cause the accumulation of considerable quantity of dairy manure which is a potential hazard to the environment. Dairy manure can also act as a principal larval resource for many insects such as the black soldier fly, Hermetia illucens. The black soldier fly larvae (BSFL) are considered as a new biotechnology to convert dairy manure into biodiesel and sugar. BSFL are a common colonizer of large variety of decomposing organic material in temperate and tropical areas. Adults do not need to be fed, except to take water, and acquired enough nutrition during larval development for reproduction. Dairy manure treated by BSFL is an economical way in animal facilities. Grease could be extracted from BSFL by petroleum ether, and then be treated with a two-step method to produce biodiesel. The digested dairy manure was hydrolyzed into sugar. In this study, approximately 1248.6 g fresh dairy manure was converted into 273.4 g dry residue by 1200 BSFL in 21 days. Approximately 15.8 g of biodiesel was gained from 70.8 g dry BSFL, and 96.2 g sugar was obtained from the digested dairy manure. The residual dry BSFL after grease extraction can be used as protein feedstuff.     

Environmental assessment of garden waste management in the Municipality of Aarhus, Denmark

An environmental assessment of six scenarios for handling of garden waste in the Municipality of Aarhus (Denmark) was performed from a life cycle perspective by means of the LCA-model EASEWASTE. In the first (baseline) scenario, the current garden waste management system based on windrow composting was assessed, while in the other five scenarios alternative solutions including incineration and home composting of fractions of the garden waste were evaluated. The environmental profile (normalised to Person Equivalent, PE) of the current garden waste management in Aarhus is in the order of −6 to 8 mPE Mg⁻¹ ww for the non-toxic categories and up to 100 mPE Mg⁻¹ ww for the toxic categories. The potential impacts on non-toxic categories are much smaller than what is found for other fractions of municipal solid waste. Incineration (up to 35% of the garden waste) and home composting (up to 18% of the garden waste) seem from an environmental point of view suitable for diverting waste away from the composting facility in order to increase its capacity. In particular the incineration of woody parts of the garden waste improved the environmental profile of the garden waste management significantly.     

The Properties of Poly(<Emphasis Type="SmallCaps">l</Emphasis>-Lactide) Prepared by Different Synthesis Procedure

Different synthesis methods were applied to determine optimal conditions for polymerization of (3S)-cis-3,6-dimethyl-1,4-dioxane-2,5-dione (l-lactide), in order to obtain poly(l-lactide) (PLLA). Bulk polymerizations (in vacuum sealed vessel, high pressure reactor and in microwave field) were performed with tin(II) 2-ethylhexanoate as the initiator. Synthesis in the vacuum sealed vessel was carried out at the temperature of 150 °C. To reduce the reaction time second polymerization process was carried out in the high pressure reactor at 100 °C and at the pressure of 138 kPa. The third type of rapid synthesis was done in the microwave reactor at 100 °C, using frequency of 2.45 GHz and power of 150 W at the temperature of 100 °C. The temperature in this method was controlled via infrared system for in-bulk measuring. The solution polymerization (with trifluoromethanesulfonic acid as initiator) was possible even at the temperature of 40 °C, yielding PLLA with narrow molecular weight distribution in a very short period of time (less than 6 h). The obtained polymers had the number-average molecular weights ranging from 43,000 to 178,000 g mol⁻¹ (polydispersity index ranging from 1 to 3) according to the gel permeation chromatography measurements. The polymer structure was characterized by Fourier transform infrared and NMR spectroscopy. Thermal properties of the obtained polymers were investigated using thermogravimetry and differential scanning calorimetry.     

Kinetic Study of Biopolymer (PHB) Synthesis in <Emphasis Type="Italic">Alcaligenes</Emphasis> sp. in Submerged Fermentation Process Using TEM

Poly-β-hydroxybuyrate (PHB) is a carbon—energy storage material which is accumulated as intracellular granule in variety of microorganism under nutrient starved conditions. Solid PHB is a biodegradable thermoplastic polymer and is utilizable in various ways similar to many conventional plastics. Ralstonia eutropha (Alcaligenes sp.), a gram negative bacteria accumulates PHB as insoluble granules inside the cells when nutrients other than carbon are limited. In this report effort has been made to analyze PHB granule synthesis inside Alcaligenes sp. NCIM 5085 by transmission electron microscopy and qualitative estimation of PHB was carried out by fourier transform infrared spectroscopy which provide better precision compared to other conventional techniques previously applied for PHB determination. Maximum PHB concentration of 2.20 ± 0.40 g/L and cell biomass of 3.42 ± 0.20 g/L was obtained after 48.0 h of fermentation. Leudking-Piret equation deduced mixed growth associated product formation which varies from earlier reports.     

Effect of Ionizing Radiation on the Morphological,Thermal and Mechanical Properties of Polyvinyl Alcohol/Polyethylene Glycol Blends

Blends of water—soluble polymers based on Poly vinyl alcohol (PVA) and Polyethylene glycol (PEG) have been prepared by the solution casting technique. The effect of various doses of γ-radiation on the structural properties of PVA/PEG polymer blends with all its compositions has been investigated. From the visual observation of all the blend compositions, it was found that, the best compatibility of the blend is up to 40% PVA/60%PEG. The structure–Property behavior of all the prepared blends before and after γ-irradiation was investigated by IR Spectroscopy, thermogravimetric analysis (TGA), mechanical properties and Scanning electron microscope (SEM). The gel content and the swelling behavior of the PVA/PEG blends were investigated. It was found that the gel content increases with increasing irradiation dose and PVA concentration in the blend. Swelling percent increased as the composition of PEG increased in the blend. The results obtained by FTIR analysis and SEM confirm the existence of possible interaction between PVA and PEG homopolymers. TGA of PVA/PEG blend, before and after γ-irradiation, showed that the unirradiated and irradiated PVA/PEG blends are more stable against thermal decomposition than pure PVA. Improvement in tensile mechanical properties of PVA/PEG blends was occurred.     

Biodegradable Water Soluble Copolymer for Antimicrobial Applications

Synthesis and characterization of novel biodegradable, water soluble and optically active DL-malic acid (DMA) and citric acid (CA) copolymers were studied for possible use as antibacterial agents. The copolymers were synthesized by direct bulk melt condensation in the absence of a catalyst above 150 °C. Characterization of obtained copolymers was carried out with the help of infrared absorption spectra, differential scanning calorimetry and thermo gravimetric analysis. The antibacterial activity of copolymers against bacteria was investigated. The results obtained shows the above copolymers possess a broad wound dressing activity against different types of bacteria and may be useful as antibacterial agents.     

In situ chemical oxidation: Lessons learned at multiple sites

This paper compiles a detailed set of in situ chemical oxidation (ISCO) lessons learned pertaining to design, execution, and safety based on global experiences over the last 20 years. While the benefits of a “correct” application are known (e.g., cost effectiveness, speed, permanence of treatment), history also provides examples of a variety of “incorrect” applications. These provide an opportunity to highlight recurring themes that resulted in failures. ISCO is, and will continue to provide, an important remedial tool for site remediation, particularly as a component of a multifaceted approach for addressing large and complex sites. Future success, however, requires an objective understanding of both the benefits and the limitations of the technology. The ability to learn from the mistakes of the past provides an opportunity to eliminate, or at least minimize, them in the future. Over the last 25 years of ISCO application, process understanding and knowledge have improved and evolved. This paper combines a thorough discussion of lessons learned through decades of ISCO implementation throughout all aspects of ISCO projects with an analysis of changes to the ISCO remediation market. By discussing the interplay of these two themes and providing recommendations from collective lessons learned, we hope to improve the future of safe, cost‐effective, and successful applications of ISCO.     

Migration of acidic groundwater seepage from uranium-tailings impoundments, 2. Geochemical behavior of radionuclides in groundwater

In this second paper of a series on groundwater seepage from uranium tailings, the general geochemical behavior of radionuclides is described and then applied to data from the field site, Seepage Area A of the Nordic Main impoundment near Elliot Lake, Ontario. The delineation of radionuclide behavior requires (1) the calculation of total element concentration by the summation of concentrations of each element's isotopes (the isotopic concentrations are calculated from the isotopes' radioactivities), (2) the evaluation of solid-liquid interactions using total element concentrations, and (3), for particular isotopes, the evaluation of the extent to which parental geochemical behavior causes a deviation in the isotope's behavior from that of its total element. A computerized speciation program, WATRAD, is used to evaluate aqueous complexation and mineral saturation indices of radium, actinium, thorium, and uranium. Data from Seepage Area A on isotopes of these four elements plus ²¹⁰Pb show that the geochemical behavior of radionuclides can be best defined on an individual isotopic basis rather than on an elemental basis.     

Probabilistic Flood Inundation Forecasting Using Rating Curve Libraries

One approach for performing uncertainty assessment in flood inundation modeling is to use an ensemble of models with different conceptualizations, parameters, and initial and boundary conditions that capture the factors contributing to uncertainty. However, the high computational expense of many hydraulic models renders their use impractical for ensemble forecasting. To address this challenge, we developed a rating curve library method for flood inundation forecasting. This method involves pre‐running a hydraulic model using multiple inflows and extracting rating curves, which prescribe a relation between streamflow and stage at various cross sections along a river reach. For a given streamflow, flood stage at each cross section is interpolated from the pre‐computed rating curve library to delineate flood inundation depths and extents at a lower computational cost. In this article, we describe the workflow for our rating curve library method and the Rating Curve based Automatic Flood Forecasting (RCAFF) software that automates this workflow. We also investigate the feasibility of using this method to transform ensemble streamflow forecasts into local, probabilistic flood inundation delineations for the Onion and Shoal Creeks in Austin, Texas. While our results show water surface elevations from RCAFF are comparable to those from the hydraulic models, the ensemble streamflow forecasts used as inputs to RCAFF are the largest source of uncertainty in predicting observed floods.